I am thinking of getting this board along with 2x2Gb Dominators PC8500 and a 45nm quad. Anyone have any experience/issues with this setup? I have seem that many of you run very high PL in memory settings. Is this a board standard? In MF1 common PL was 6 or 7. Does the EK NB-Smax fit on the NB?
Grnfinger show me some good results of O/C cause i still cant make my mind over MF2 or RE
Intel i7 3770K (4.8Ghz@1.36v) ~ Asus Maximus V Gene ~ 8Gb G.Skill Ripjaws X 2133 C9 (@2400 C10) ~ Asus GTX 670 DCUII (1230/7000) ~ Samsung 840 Pro 128Gb ~ WD Black 1Tb ~ Corsair AX 850W ~ X-Fi Titanium Fatal1ty ~ Epoz Aktimate Mini ~ Ducky Shine Blue Led /w MX Red ~ Logitech G700 ~ Samsung S27A850D 27" (2440x1600) ~ SilverStone TJ07B-W
WaterCooled by XSPC Raystorm ~ TC PA 120.3 + 3xAP 15 ~ MCP655 with EK-D5 X-Top Rev.2 ~ EK Multi 250
Powered by APC Smart-UPS SC 1500 ~ MGE ellipse premium 500
I
I have:
FSB: 400
FSB Termination vontage: 1.25v
PLL: 1.51
NB: 1.20
SV: 1.10
and my NB have 90º... what is the problem?
MY SYSTEM: BENQ 27" LED XL2720Z | PHANTEKS ENTHOO PRIMO BLACK | EATON ELLIPSE ECO 800VA | ENERMAX PLATIMAX 750W | ASUS Z270 MAXIMUS IX HERO | INTEL i7 6700K | NOCTUA NH-D15S | CORSAIR VENGEANCE LPX DDR4 3200MHZ 16GB | MSI GTX980 GAMING 4GB | ASUS XONAR ESSENCE STX II | LOGITECH Z-5500 | SAMSUNG SSD 850 EVO 500GB | 2x WESTERN DIGITAL GREEN 4TB SATA III | ROCCAT RYOS MK PT | STEELSERIES RIVAL 300 | STEELSERIES 4HD | LOGITECH GAMEPAD F510
get the heatsink off , reapply paste (arctic ceramique) and put a washer to put more pressure on the springs so the NB is really tied down... it has bad contact mate at the moment and is not good to continue to use the board under these conditions... you will smoke itOriginally Posted by psychopath
Question : Why do some overclockers switch into d*ckmode when money is involved
Remark : They call me Pro AsusSaaya yupp, I agree
your NB block has a bad contact with the nb chip.. i had the same problem. you can fix this by taking off the whole nb heatsink, then clean off the thermal paste and put new layer of it to the heatsink.. then when you put your heatsink back to your board, put 2 washers where the 2 heatsink holes are located, fasten all the screws and your ready to rock
Evga X58 sli under cascade
http://www.xtremesystems.org/forums/...d.php?t=219788
Evga X58 Sli ultimate overclocking/ overview/ discussion thread
http://www.xtremesystems.org/forums/...d.php?t=221082
proud owner of E8600 Q822A435
Hey guys
How's this board with the Q6600's I'm on the settings of my signature on a P5K deluxe...
Do you think it's a good board to go for ?
I was lookin' at the rampage and the P5Q deluxe but this one seems very good
Cheers
Sergio
Intel Core i9-7980XE@ 4.8GHz 18C/18TH (Direct Die Contact)
ASRock X299 OC Formula
ADATA XPG SPECTRIX D80 (4x8GB) DDR4-3800C17 B-Die
1x Intel Optane SSD 905P 480GB
4x HP EX950 NVMe 2TB on ASRock ULTRA M.2 CARD
EVGA RTX 2080TI KINGPIN 2190/8000 Stock Cooling AIO 240
SilverStone ST1500W-TI TITANIUM
Alphacool Custom Water Cooling
Wel i could not get much higher then 3.6Ghz stable.But on this bord it did need less voltage like less vtt less nb and less vcore.On my mf1 it was 1.42 vtt , 1.51 Nb , and 1.41vcore.With mf2 it was vtt 1.34 Nb 1.41 and vcore 1.38.Now i use E8600 8.5x 500 with very low voltage.So for me this bord was a good buy.
Reply With Quote
Bookmarks