ASUS P5Q-E (P45) pre-view

[thehinge1]

Will do, been preoccupied with other things today, but I should have a while to play with it tomorrow... can get just short of good mem scores at 550fsb 1:1 on bios 1103 but got kinda frustrated after hitting DDR1224 on the now-gone P5K with great bandwidth (at only 461fsb though). I may concentrate on 533fsb 1:1 as I'm about to go 4GB 2x2GB Reapers on the P5Q-E and bios 1201 is ready to go

Here is a functional 550fsb setting in the meantime:
ASUS P5Q-E Template :

*Note*: I lost my original 550fsb setting that definitely had some tighter timings and lower voltages in places, but this setup is bomber thus far. I will update again when I find some sweeter spots

Cpu Frequency with this setup is 3.85GHz, initial SuperPI 1M time is 13.235 sec - I think very low 13's or even lower may be possible.

CPU is M0 stepping E7200 retail boxed, air cooled w/TRUE120 & 1500rpm Scythe/Sony FDB SFF21F 120mm
P5Q-E rev. 1.01G on bios 1103
RAM used: OCZ Reaper PC2-9200/DDR1150
No fans over 900rpm in case to keep things nice and quiet

JumperFree Configuration Settings
AI Overclock tuner: MANUAL
CPU Ratio Setting: 7.0
FSB Frequency: 550
PCI-E Frequency: 100
FSB Strap to North Bridge: AUTO
DRAM Frequency: 1000 (BIOS says DDR2-1102)
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: MANUAL

1st Information : 5-5-5-18-11-36-6-11

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 18
RAS# to RAS# Delay : 11
Row Refresh Cycle Time: AUTO (for this RAM is 36)
Write Recovery Time: 6
Read to Precharge Time: 11

2nd Information : 11-5-5-4-5-5-6

READ to WRITE Delay (S/D): 11
Write to Read Delay (S): 5
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): 5
WRITE to WRITE Delay (D): AUTO

3rd Information : 14-13-1-5-5

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: Disabled
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: AUTO (I think it is PL-13 at this clock freq)

CPU Voltage: 1.33750
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.66
FSB Termination Voltage: 1.28
DRAM Voltage: 2.04
NB Voltage: 1.34
NB GTL Reference: AUTO
SBridge Voltage: AUTO
PCIE SATA Voltage: AUTO

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Delay 400ps
NB Clock Skew : Delay 200ps
CPU Margin Enhancement: Optimized

Advance CPU Settings
CPU Ratio Setting: 7.0
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled

Anyone out there please feel free to warn me if you think I'm at 'danger level' on any of these voltages.

@ thehinge1
Please submit your impression about bios 1201 compared to 1103 if you are going to flash it.