"ASUS P5Q Deluxe discussion".

[cadaveca]

P5QL-E: (0602):
1. Revision opens the phenomenon unable to open EIST at the same time after C-State
2. Phenomenon that will not shut down automatically after revision matches four key CPU and uses CrashFree
3. Promote the compatibility with Prescott series CPU
4. Promote and exceed the sex frequently

[Kartoff]

[yenclas]

Hello.

I'm Spanish. Sorry by my bad English.

I buy this great motheboard this week and I cannot leave stable at 500*8. With my old motheboard I have this settings totally stable (10 hours dual prime stable).

My system is:

P5Q Deluxe, Intel 8400, and GSKILL 2x2Gb DDR 1000

JumperFree Configuration Settings:

AI Overclock tuner: Manual
CPU Ratio Setting: 8
FSB Strap to North Bridge: 333
FSB Frequency: 500
PCI-E Frequency: 100
DRAM Frequency: 1000Mhz
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual

1st Information :

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: 55
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information :

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information :

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: Disabled
MEM. OC Charger: Enabled
AI Clock Twister: Lighter
AI Transaction Booster: Manual
Common Performance Level [10]
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED

CPU Voltage: 1.40000
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.58
FSB Termination Voltage: 1.32
DRAM Voltage: 2.04
NB Voltage: 1.32
NB GTL Reference: AUTO
SBridge Voltage: 1.20
PCIE SATA Voltage: 1.60

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Auto
NB Clock Skew : Auto

Advance CPU Settings
CPU Ratio Setting: 8
CPU VID: Default
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled


What can I do ?

[yenclas]

Hello.

I'm Spanish. Sorry by my bad English.

I buy this great motheboard this week and I cannot leave stable at 500*8. With my old motheboard I have this settings totally stable (10 hours dual prime stable).

My system is:

P5Q Deluxe, Intel 8400, and GSKILL 2x2Gb DDR 1000

JumperFree Configuration Settings:

AI Overclock tuner: Manual
CPU Ratio Setting: 8
FSB Strap to North Bridge: 333
FSB Frequency: 500
PCI-E Frequency: 100
DRAM Frequency: 1000Mhz
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual

1st Information :

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: 55
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information :

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information :

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: Disabled
MEM. OC Charger: Enabled
AI Clock Twister: Lighter
AI Transaction Booster: Manual
Common Performance Level [10]
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED

CPU Voltage: 1.40000
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.58
FSB Termination Voltage: 1.32
DRAM Voltage: 2.04
NB Voltage: 1.32
NB GTL Reference: AUTO
SBridge Voltage: 1.20
PCIE SATA Voltage: 1.60

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Auto
NB Clock Skew : Auto

Advance CPU Settings
CPU Ratio Setting: 8
CPU VID: Default
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled


What can I do ?

Leeghoofd,

What do you think about my problem ?

[JHS]

Hmm. had to drop performance level from 8 to 10 with bios 1102 compared to 803


Anyone else noticed something similiar?

[Leeghoofd]

Leeghoofd,

What do you think about my problem ?

try these plz :

DRAM Read Training: Disabled
MEM. OC Charger: Enabled
AI Clock Twister: AUTO
AI Transaction Booster: AUTO

CPU Voltage: 1.40000
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.52
FSB Termination Voltage: 1.26
DRAM Voltage: 1.96
NB Voltage: 1.28
NB GTL Reference: AUTO
SBridge Voltage: AUTO
PCIE SATA Voltage: AUTO

It's weird that the testing programs beahve so erratically... prime failing within minutes and OCCT going on for hours... I don't need as high voltages on my chipsets nor rams... try to alter one setting at a time... to find out where it could be... but again 1.4vcore is prety high with LLC enabled... CPu temps not an issue (although 45Nm is a pos to readout)

If this is stable then you can start to tweak again... but first you need to get this CPU stable sir

Hmm. had to drop performance level from 8 to 10 with bios 1102 compared to 803
Anyone else noticed something similiar?

With which FSB ? ram speed ? Rams used ? I didn't notice any changes with my hardware, all my previous settings and pl levels booted fine liek before...

[JHS]

try these plz :
With which FSB ? ram speed ? Rams used ? I didn't notice any changes with my hardware, all my previous settings and pl levels booted fine liek before...

Looks like it just needed bit more voltage than 8.03. Now I just have to find out which setting it was. I'm running pretty low voltages overall

oh and FSB = 447 atm
I set ram to auto/under normal values to make sure it was not DRAM issue


I raised
NB 1.12 -> 1.14
FSB terminate 1.12->1.14
CPU PLL 1.52->1.54


Still running in safe waters but I want to test what actually allowed me to boot with lower PL..

[Leeghoofd]

Looks like it just needed bit more voltage than 8.03. Now I just have to find out which setting it was. I'm running pretty low voltages overall

oh and FSB = 447 atm
I set ram to auto/under normal values to make sure it was not DRAM issue


I raised
NB 1.12 -> 1.14
FSB terminate 1.12->1.14
CPU PLL 1.52->1.54


Still running in safe waters but I want to test what actually allowed me to boot with lower PL..

Well most of run 1.2plus volts for Nb... I use 1.22 for 450 and 1.26 for 500FSB... FSB term voltage I go with 1.2-1.26 range for all my CPU's