DFI first DDR3 motherboard, UT X48-T3R Heatsink by Thermalright

[Roger_D25]

I'm pretty sure both the T2R and T3R come with actual Thermalright heatsinks (and ability to add the HR NB block, even comes with mounting hardware to make the HR work)! I just ordered one myself and looking forward to getting it!

EDIT REASON: Idiot!

[Praz]

The heatsink assemblies are the same on the DDR2 and DDR3 UT boards.

[disruptfam]

ok cool so you get the hr 05 on the nb and the hr 05 that hangs out the case?


i wasn't sure because all the x48 tr2's look like this




cheers guys!!!

[AriciU]

ok cool so you get the hr 05 on the nb and the hr 05 that hangs out the case?


i wasn't sure because all the x48 tr2's look like this




cheers guys!!!

That's the LT version. It does not come with the heatpipe cooling solution and the external heatsink. Those are only for the UT versions and i don't know if DFI has an UT X48 T2R... not in my country anyway.

[disruptfam]

ahhhhhk i get ya there are lt and ut variants.

edit: there are no Ut dfi x48's in Aus

[biftek.]

Didn't Thermalright make the X48 LT NB heat sink also though?
I'm pretty sure i remember reading that in my owners booklets and stuff.

[SquidgyB]

As far as I know, there is no UT variant of the T2R, so you have to live with that "minotaur" heatsink assembly. The T3R comes with a "hedgehog" style heatsink for the northbridge, you'd have to buy a HR-05 to put there if you wanted one, though if you had a TRUE120, you'd probably need an HR-05 SLI so it would fit.

[quake6]

Yes,there is UT T2R version and they are available at my place...

[Praz]

As far as I know, there is no UT variant of the T2R

Really doubt that I have the only UT DDR2 board made.

[Praz]

Thanks goes to Fiery. All voltages, fans and temps are now displayed. A couple of the voltage readings are off though. It is being worked on.

Everest Ultimate Beta

[SquidgyB]

Really doubt that I have the only UT DDR2 board made.

My apologies, I've only been following DDR3 boards with any interest.

[Matias23]

What is the difference between X48 UT T3R and X48 UT T3RS ?

[emoners]

Really doubt that I have the only UT DDR2 board made.

coz DFI loves you

anyway, just got my UT T2R





hoping to have some free time soon...

[AriciU]

What is the difference between X48 UT T3R and X48 UT T3RS ?

I'm interested in that as well. Better capacitors?

[SquidgyB]

I think the UT versions have a digital PWM while the LTs have an analogue one, but going on my track record with info I wouldn't quote me

[quake6]

Nope,he asked about T3RS and T3R.Probably in number of SATA connector,that was difference with DK series and difference about UT and LT is only in cooling,nothing more

[SquidgyB]

Told you my info was untrustworthy. Add to that the fact that I apparently can't read and you get to where my post was

[Praz]

DFI LP UT X48-T3RS, 06/09 BIOS
E8400
480x8.5, Memory 1600MHz
2x2GB OCZ PC3-12800 1600MHz Platinum EB
2x2GB PCZ PC3-10666 1333MHz ReaperX
XFX8800 GTS (G92)
tRD - 8.3, Memset Misreads The Value When Set Manually
Memory Speed - 1600MHZ, CPU-Z Misreports The Divider


click for larger image


click for larger image


click for larger image


click for larger image

CPU Feature Page
Thermal Management Control................Enabled
PPM (EIST) Mode...........................Disabled
Limit CPUID MaxVal........................Disabled
CIE Function..............................Disabled
Virtualization Technology.................Disabled
Core Multi-Processing.....................Enabled

Main BIOS Page
Exist Setup Shutdown......................Mode 2
Shutdown After AC Loss....................Disabled
O. C. Fail Retry Counter..................0
CLOCK VC0 Divider.........................Auto
CPU Clock Ratio...........................8.5x
CPU N/2 Ratio.............................Enabled
CPU Clock.................................480 MHz
Boot Up Clock.............................Auto
CPU Clock Amplitude.......................800mV
CPU Clock0 Skew...........................0ps
CPU Clock0 Skew...........................0ps
DRAM Speed................................400/1333
PCIE Clock................................100MHz
PCIE Slot Config..........................1X 1X

CPU Spread Spectrum.......................Disabled
PCIE Spread Spectrum......................Disabled
SATA Spread Spectrum......................Disabled

Voltage Setting Page 
CPU VID Control...........................1.36250V
CPU VID Special Add Limit.................Enabled
CPU VID Special Add.......................Auto
DRAM Voltage Control......................1.874V
SB Core/CPU PLL Voltage...................1.510V
NB Core Voltage...........................1.630V
CPU VTT Voltage...........................1.200V
VCore Droop Control.......................Disabled
Clockgen Voltage Control..................3.45V
GTL+ Buffers Strength.....................Strong
Host Slew Rate............................Weak
GTL REF Voltage Control...................Disabled
CPU GTL 1/2 REF Volt......................113
CPU GTL 0/3 REF Volt......................100
North Bridge GTL REF Volt ................100

DRAM Timing Page
Enhance Data Transmitting.................Fast
Enhance Addressing........................Fast
T2 Dispatch...............................Disabled
Clock Setting Fine Delay..................Listed Below
CAS Latency Time (tCL)....................7
RAS# to CAS# Delay (tRCD).................6
RAS# Precharge (tRP)......................6
Precharge Delay (tRAS)....................20
All Precharge to Act......................7
REF to ACT Delay (tRFC)...................60
Performance Level.........................9
Read Delay Phase Adjust...................Listed Below
MCH ODT Latency...........................Auto
Write to PRE Delay (tWR)..................18
Rank Write to Read (tWTR).................13
ACT to ACT Delay (tRRD)...................4
Read to Write Delay (tRDWR)...............8
Ranks Write to Write (tWRWR)..............Auto
Ranks Read to Read (tRDRD)................Auto
Ranks Write to Read (tWRRD)...............Auto
Read CAS# Precharge (tRTP)................5
ALL PRE to Refresh........................7

Read Delay Phase Adjust Page
Channel 1 Phase 0 Pull-In.................Enabled
Channel 1 Phase 1 Pull-In.................Enabled
Channel 1 Phase 2 Pull-In.................Enabled
Channel 1 Phase 3 Pull-In.................Enabled
Channel 1 Phase 4 Pull-In.................Enabled

Channel 2 Phase 0 Pull-In.................Auto
Channel 2 Phase 1 Pull-In.................Auto
Channel 2 Phase 2 Pull-In.................Auto
Channel 2 Phase 3 Pull-In.................Enabled
Channel 2 Phase 4 Pull-In.................Enabled

Clock Setting Fine Delay Page
DRAM Default Skew Model...................Model 3

Fine Delay Step Degree....................50ps


Ch1 Clock Crossing Setting................Auto
DIMM 1 Clock fine delay...................Current 489ps
DIMM 2 Clock fine delay...................Current 489ps
DIMM 1 Control fine delay.................Current 434ps
DIMM 2 Control fine delay.................Current 473ps
Ch 1 Command fine delay...................Current 550ps

Ch2 Clock Crossing Setting................Auto
DIMM 3 Clock fine delay...................Current 686ps
DIMM 4 Clock fine delay...................Current 686ps
DIMM 3 Control fine delay.................Current 607ps
DIMM 4 Control fine delay.................Current 654ps
Ch 2 Command fine delay...................Current 700ps

Ch1Ch2 CommonClock Setting................Auto

Ch1 RDCAS GNT-Chip Delay..................Auto
Ch1 WRCAS GNT-Chip Delay..................Auto
Ch1 Command to CS Delay...................Auto

Ch2 RDCAS GNT-Chip Delay..................Auto
Ch2 WRCAS GNT-Chip Delay..................Auto
Ch2 Command to CS Delay...................Auto

Common CMD to CS Timing...................2N

click for larger image

[Praz]

Vista 64 Bit SP1


click for larger image



click for larger image



click for larger image



click for larger image






3dx Max w/V-ray
Time to render: 15min 36sec

click for larger image



click for larger image

[jugeen]

I think the UT versions have a digital PWM while the LTs have an analogue one, but going on my track record with info I wouldn't quote me

both have digital pwm

[karlpox]

is there a problem between this board and quad fire 3870x2? got 2 3870x2's running, but my lcd wont display anything on the pci-e 1 but the pci-e 3 works though.

[AriciU]

Still no max FSB Praz?

[NinjaZX6R]

Hey Guys!

*SUBSCRIBED!*

Mine will be here tomorrow hopefully. Does this come with just the cooler that sticks out the back of the case, or does it come with the large HR-05-like NB cooler as well? Newegg's picture only showed the rear heatsink.

Anyway, I'll be testing max FSB with the E8600 E0 I got today. Should be VERY exciting and I'll definitely post as soon as I can.

Still haven't seen anyone posting 550+ FSB with this, though.

-Collin-

[p0tter]

Heatpipes done correctly.

Go DFI!

[Praz]

Heatpipes done correctly.

Go DFI!

For sure. Compare board voltage to temperatures. I removed the finned upper portion of the NB heatsink and put a MCW30 on it.