Water Cooled Case Gallery

[biftek.]

Hey Raxxath, mind posting some pics of the A05 internals?

[The[R]eaper]

Hey, Bugkalot, what tubing is that?

Looks great +1 to more pics.

[rafwlkp]

bugkalot Malik style ^^
Show more pics mate


EDIT:

Hey, Bugkalot, what tubing is that?

Looks great +1 to more pics.

This is Feser One blue tube

[The[R]eaper]

^^ thanks looks great

[Sugar4o]

Awesome tubing!!!
Can I make one suggestion. I’m not sure if it is possible but I would swap the 2 tubes on the north bridge to avoid the knee between the processor outlet and chipset inlet.
The other option is to rotate the chipset block.

[xTKxhom3r]

Awesome tubing!!!
Can I make one suggestion. I’m not sure if it is possible but I would swap the 2 tubes on the north bridge to avoid the knee between the processor outlet and chipset inlet.
The other option is to rotate the chipset block.

yup thats a very good suggestion and the tubing is real nice...

[atlxkevinx]

Wow!!! So many very clean builds! I wish I can mod like some of you guys, very jealous. I have a few questions.

1. Right now I have my pump > cpu > radiator > reservoir and I see most people run from pump > cpu first. Is that going to be a big difference in temp?
2. And also, I am using a D-tek cpu block and MCR320 (brass body & tubes) so is it okay just to distilled water + PT Nuke or will I need anti-corrosion protection? What type of mix is the most simple + safe? Distilled water + PT Nuke?
3. What type of tubes do you guys recommend? I am currently using the Masterkleer 7/16" ID.

Here are some pics of my quick build. I am moving out soon so I will rebuild it when I move out and get new tubes.





Any recommandations or tips to help me improve my system?

[ls206]

Looks good, but what's that strange twist in the tubing, rad -> res O_o

[atlxkevinx]

Haha, yeah.. I like it. The reason I did that was because I did not want the tubes to rest on top of the other tubes, and it looks bad. I wouldn't think performance would be affected by it.

[Aldy402]

looks good, just get some neoprene or something under the pump to reduce vibrations to the drive cage..

[Bubbaxm2]

Few pics of my Thermaltake Armor.
First one is what it used to look like. The rest are current.

[CyberDruid]

@Raxxath: Superb cable management. That's a very thoughtful build.

[WheelMan]

Just a little teaser. Far from done yet

*huge-ish picture*

I like your work ^_^

Keep it up!

[MomijiTMO]

1. Right now I have my pump > cpu > radiator > reservoir and I see most people run from pump > cpu first. Is that going to be a big difference in temp?
2. And also, I am using a D-tek cpu block and MCR320 (brass body & tubes) so is it okay just to distilled water + PT Nuke or will I need anti-corrosion protection? What type of mix is the most simple + safe? Distilled water + PT Nuke?
3. What type of tubes do you guys recommend? I am currently using the Masterkleer 7/16" ID.

1. For your loop it doesn't matter. People have done that for pressure reasons on a multi block loop that has several large restriction points.
2. Nothing can corrode in your loop.
3. That tubing is fine. Most people here use Tygon tubing as it doesn't suffer from the plasticiser leech [well as much as other tubing]. You might find that 1/2" ID might give you a better flow rate and subsequently better temperatures but it is best if you read one of the stickied threads on tubing size and the effect on temperature.

Cheers.

[Kaister]

So I am about this fire this baby up.

My goals were:
Looks good, great sidewindow appeal but not tacky.
All has to be inside, no external rads.
No wire clutter.
Must run cool and especially quiet, yet allowing for a decent overclock.

the only challenge: How to mount a Thermochill RAD 120.3 into the Lian Li armorsuite without drilling to many 120mm holes into the bottom. I wanted the vertical arrangement to allow the air from the front 3 14cm fans to be utilized.
It is a bit tough to get to the drive bays.....I get there from the front of the case.

See for yourself. Sorry for the wires of the GPU....as I said...not quite finished yet.

http://picasaweb.google.com/kaispeth...54498097357186
http://picasaweb.google.com/kaispeth...54362105619186
http://picasaweb.google.com/kaispeth...54436848700002

Lian Li armorsuite, TT 1200W PSU, Asus Striker II Extreme, E8500, 4GB of Patriot Viper, 2 eVGA 8800GTX with DD blocks, D-tek Fusion, Aquastream XT Ultra, 2 Raptors @ 150GB each (Raid0), 3 Seagates @1TBea (Raid 5), 3ware PCI-e RAID controller...Thermochill Rad PA 120.3

[bundymania]

Radiator on Fire

[MomijiTMO]

Damn that rad and the shrouds are just awesome.

[Burn]

What radiator shrouds are those?

[eXa]

thats the Feser ones.

[Burn]

Can we get them separately? Or do they have to be purchased with the radiator? I would love to get 3 for mine.

[Fr3ak]

You can get them separately in the colors gree, blue and red.

Looks really nice, I will post some pics very soon too

[Arni]

That looks like truck on gta 3 "she's on fire and she's burning" : : D

[bundymania]

...some more disco feeling







...and a teaser from my upcoming project

[Fr3ak]

The shourds dont just look good, they result in a better airflow => 1-2C better temps

Nice pictures!

[disruptfam]

very slick bundy!