Board flashed and up and running again. No visible differences in BIOS that I can see but have to admit that I have only glanced through it after flashing. Started some OC'ing to see if 0501 BIOS is more FSB friendly for my Quad but initial findings seems to indicate less clockability. Will experiment more lately and try some more Volts. Please prove me wrong...![]()
After some more testing it seems that there is nothing wrong with BIOS 0501 as compared to 0401, which I found very stabile. It also seems that at least SuperPI is benchable on higher MHz with 0501 than 0401 as I now managed to run 1 Mill. at 4,909,5 and also managed to CPU-Z verify at a higher frequency as well (4.983MHz). All runs on my 24/7 machine with aloads of processes running in the background and with no tweaking of disk or Vista Ultimate what so ever.
http://valid.x86-secret.com/show_oc.php?id=373611
Some my results with E7200 on max FSB tried so this mobo it's very very impressive for FSB
Pi1M@581FSB (7.5x multi)
Pi32M@581FSB (7x multi)
E7200@4.4GHz(550FSB)
![]()
Sorry For My English
OverclockZone Team
THAILAND
These are my settings with the 0115
For later bioses you must NOT set the fsb strap to Auto.
With these settings i can use the 2/3 and the 5/8 dividers(1744 - 1857)
And here are fresh results :p
![]()
On my setting and boost from bios
CPU Ratio : 7.5
FSB Strap : 266
FSB Freq : 581
PCIE Freq : 101
DRAM Static Read : Auto
DRAM Dynamic Write : Auto
AI Clock Twister : Auto
AI Transaction : Auto ( Maybe Manual and setting = 9 )
CPU Voltage : 1.7500
CPU GTL : 0.63x
CPU PLL : 1.64
FSB : 1.44
DRAM : 2.08
NB : 1.55
NB GTL : 0.61x
SB : 1.20
Clock Over : 0.7
Load-Line : Performance
CPU Spread : Disable
PCIE Spread : Disable
For Sub-Timing i setting follow SPD showing but have something not goodit's Performance Level = 9 if change to 8 it not boot if setting CL6 perf lvl will good it'll boot at 6 too
Thanks![]()
Last edited by ZoLKoRn; 06-11-2008 at 03:13 AM.
Sorry For My English
OverclockZone Team
THAILAND
why do you use 201 bios?![]()
you can set the strap manually with the old bios![]()
Up and runningMy first DDR3 board so a lot of work to be done. Started testing mem vdimm 1.96v bios. What you guys use to read vdimm in windows?
![]()
# Sav,
My experiences with my 2x2GB Corsair memory (1800 Dominator, see sig) with respect to running them at DDR1800 are:
1) It is mandatory to use the BLACK slots.
2) Use the 333 FSB strap to NB.
3) I advice to use Memtest 86+ v. 2.01 to test when tweaking for the right settings - errors will come fast (especially test 5) and you have a good idea what is causing the errors.
4) 1N is possible.
5) You need 1.5+ NB voltage (and I suggest active or watercooling on NB).
I have spent a LOT of time (and godwill from xt0m, thanks) trying to run DDR1800 stable. I wasted a lot of time Priming (e.g. 7 h stable blend test that suddenly would give an BSOD at ordinary use) at settings that made errors within few minutes in Memtest. Therefore I will not yet brag about beeing stable at that speed. However, now I have found settings at 9x450, DDR1800 cabable of completing at least 2 full passes. Tomorrow I will tell if it is truely stable in Memtest and then I will Prime to see whether the settings are stable in Windows when the CPU is loaded as well.
I'm sure you can't wait until tomorrow to se my settings so here they are (even though I can not claim they are truely stable yet or the voltages can not be lowered):
BIOS 0501
Multi: 9
FSB strap: 333
FSB: 450
PCIE: 100
DRAM: 1800
CMD: 1N
Primary timings: 8-8-8-25, the rest Auto
2nd and 3rd timings: All Auto
Dynamic and static read/write control: both Disable
CPU: 1.4625
CPU GTL: 0.65
PLL: 1.5
FSB TV: 1.4
NB: 1.55
NB GTL: 0.61
SB: Auto
C O-C V: Auto
LLC: Performance
Hope this will help you and others struggeling with 2x2GB memory.
****UPDATE: The above settings are Memtest 86+ v. 2.01 stable for 8 h+ (18 full passes) so at least the memory is stable. Priming at the moment with the same settings.****
Last edited by Holmer; 06-11-2008 at 11:07 PM.
CPU: QX9650 @4.25.
MB: Asus P5E64 WS Evolution (BIOS 0702).
WC: Swiftech GTZ, XSPC X20 Delta, EK FC4870X2 CF, 2x Laing DDC 18W w. XSPC Top, HW-labs GTS 360 Xflow, Swiftech MCR120-RES.
HDD: Intel X25-M 160 G2 + Mtron Mobi 32 GB SSD + 2x 1 TB Samsung Spinpoint F1.
GFX: Club3D 4870X2 @790/915 (Asus TOP).
RAM: 2x2 GB Corsair TW3X4G1800C8DF G (8-7-7-18-1T-PL6 @1700 MHz).
PSU: Corsair HX1000W.
Case: Coolermaster Cosmos S.
Speakers: Logitech Z-5500 digital 5.1.
Soundcard: Auzen X-Fi Prelude 7.1.
DVD: Samsung Super Writemaster SATA DVD burner.
LCD: Dell U2410.
OS: Windows 7 Ultimate 64.
The settings that were stable in Memtest was not stable in Prime95. Right now I am Priming with the following settings (changes in bold):
Multi: 9
FSB strap: 333
FSB: 450
PCIE: 100
DRAM: 1800
CMD: 1N
Primary timings: 8-8-8-25, the rest Auto
2nd and 3rd timings: All Auto
Dynamic and static read/write control: both Disable
CPU: 1.4625
CPU GTL: 0.63x
PLL: 1.5
FSB TV: 1.36
NB: 1.55
NB GTL: 0.67
SB: Auto
C O-C V: Auto
LLC: Performance
***UPDATE the above settings are at least 12 hours Prime95 (small FTT) stable, now testing Prime95 blend.***
Last edited by Holmer; 06-12-2008 at 10:40 PM.
CPU: QX9650 @4.25.
MB: Asus P5E64 WS Evolution (BIOS 0702).
WC: Swiftech GTZ, XSPC X20 Delta, EK FC4870X2 CF, 2x Laing DDC 18W w. XSPC Top, HW-labs GTS 360 Xflow, Swiftech MCR120-RES.
HDD: Intel X25-M 160 G2 + Mtron Mobi 32 GB SSD + 2x 1 TB Samsung Spinpoint F1.
GFX: Club3D 4870X2 @790/915 (Asus TOP).
RAM: 2x2 GB Corsair TW3X4G1800C8DF G (8-7-7-18-1T-PL6 @1700 MHz).
PSU: Corsair HX1000W.
Case: Coolermaster Cosmos S.
Speakers: Logitech Z-5500 digital 5.1.
Soundcard: Auzen X-Fi Prelude 7.1.
DVD: Samsung Super Writemaster SATA DVD burner.
LCD: Dell U2410.
OS: Windows 7 Ultimate 64.
you re welcome
the 0115 have an issue with the 1/2.
be aware from this divider :p
Bookmarks