Heres what I get with 2800mhz up to 2846mhz same settings

DFI LANPARTY UT 790FX-M2R (BIOS 4/15/2008 "Beta")

AMD Phenom 9850 Black Edition "B3"

Tuniq Tower 120

OCZ Reaper HPC (PC2-8500) 5-5-5-18 2X2GB

POWERCOLOR AX3870 X2 CROSSFIRE CATALYST 8.3

Auzentech XPlosion

Areca 1231 ML {Intel IOP 341} ~ 6 ~ 250gb Hitachi Sata II Raid 6 ~2~WD 74gb Raptors ~ Raid 0 ~

Plextor 750A

SilverStone OP1000

CM Stacker STC-T01

Code:
>HT Link Control:
 
HT Link Width......................... - 16 bit
HT Frequency.......................... - 2GHZ MHz
IH Flow Control Mode.................. - Disabled
HT Link Tristate...................... - Disabled
2x LCLK Mode.......................... - Disabled
Unit Id Clumping...................... - Disabled
 
>CPU Feature:
 
CPU DID.............................. - 1
CPU FID.............................. - 0C
CPU-NB DID........................... - 1
CPU-NB FID........................... - 06
AMD CPU stepping..................... - P0

>DRAM Configuration:

MCT Memory Timing.................... - Manual
2T Mode.............................. - Auto
Cas Latency Time..................... - 5
Pre Charge Delay (tRAS).............. - 18
DRAM RAS# Precharge.................. - 5
DRAN RAS# to CAS# Delay.............. - 5
Bank to Bank Cmd (TRRD).............. - Auto
TRC.................................. - 23T
TRTP................................. - Auto
Write Recovery (TWR)................. - Auto
Write-Read Command (TWTR)............ - Auto
TRFC0................................ - 195ns
TRFC1................................ - 195ns
TRFC2................................ - 195ns
TRFC3................................ - 195ns
Trdrd................................ - Auto
TrwtT0............................... - Auto
Twrrd................................ - Auto
Twrwr................................ - Auto
CS/ODT Pin Fine Delay................ - Enabled
Bank Swizzle Mode.................... - Enabled
Auto Tweak Performance............... - Enabled
Optimal Performance Mode............. - Enabled

>ODC Control Mode:

DRAM Drivers Weak Mode.............. - Normal
Output Drivers Comp................. - Normal
>Channel A:
CPU On-die Termination.............. - 300 ohms +/- 20%
DQS Drive Strength.................. - 1.00x
Data Drive Strength................. - 1.00x
MEMCLK Drive Strength............... - 1.00x
Addr/Cmd Drive Strength............. - 1.50x
CS/ODT Drive Strength............... - 1.50x
CKE Drive Strenght.................. - 1.50x
>Channel B:
CPU On-die Termination.............. - 300 ohms +/- 20%
DQS Drive Strength.................. - 1.00x
Data Drive Strength................. - 1.00x
MEMCLK Drive Strength............... - 1.00x
Addr/Cmd Drive Strength............. - 1.50x
CS/ODT Drive Strength............... - 1.50x
CKE Drive Strenght.................. - 1.50x


>PWM Settings:
 
PWM Control.......................... - Enabled
CPU VID Control...................... - 1.2500v
CPU Vid Special Add.................. - Auto
CPU NB Vlotage Control............... - Auto
CPU NB Vid Special Add............... - Auto
DRAM Voltage Control................. - 1.80v
SB PLL 1.2V Voltage.................. - 1.20v
NB Core Voltage...................... - 1.250v
NB PCI-E Voltage..................... - 1.120v
NB HT Voltage........................ - 1.270v

 
Genie BIOS Settings:
 
Timing Mode.......................... - Manual
Memory Clock value or Limit.......... - DDR 1066
PCIE 3,4 State....................... - Auto
PCIE 2 State......................... - x2
CPU TLB Cache Fix.................... - Disabled
AMD K8 Cool & Quiet control.......... - Disabled
CPU Clock Ratio...................... - Auto
Spread Spectrum...................... - Disabled
CPU Host/HTT Clock................... - 200mhz
CPU Host/HTT Boot Up Clock........... - 200mhz
CPU Host/HTT Adjustment Gap.......... - 5mhz
PCIE Clock........................... - 100mhz