Dede99 looks like you have the new Tracer and are settings won't work for you, any chance of swapping them for the old ones?
Code:CPU Feature Page Thermal Management Control................Disabled PPM (EIST) Mode...........................Disabled Limit CPUID MaxVal........................Disabled CIE Function..............................Auto Execute Disable Bit.......................Disabled Virtualization Technology.................Enable Core Multi-Processing.....................Enabled Main BIOS Page Exist Setup Shutdown......................Mode 2 Shutdown After AC Loss....................Disabled O. C. Fail Retry Counter..................0 CLOCK VC0 Divider.........................Auto CPU Clock Ratio...........................9x CPU Clock.................................451 MHz Boot Up Clock.............................Auto DRAM Speed................................400/1066 PCIE Clock................................110 MHz PCIE Slot Config..........................1X 1X CPU Spread Spectrum.......................Disabled PCIE Spread Spectrum......................Disabled SATA Spread Spectrum......................Disabled Voltage Setting Page CPU VID Control...........................1.50V CPU VID Special Add.......................Auto DRAM Voltage Control......................2.430V SB Core/CPU PLL Voltage...................1.760V NB Core Voltage...........................1.530V (realvolt=1.48v) CPU VTT Voltage...........................1.448V (realvolt=1.43v) VCore Droop Control.......................Disabled Clockgen Voltage Control..................3.45V GTL+ Buffers Strength.....................Strong Host Slew Rate............................Weak GTL REF Voltage Control...................Disabled CPU GTL1/3 REF Volt.......................N/A CPU GTL 0/2 REF Volt......................N/A North Bridge GTL REF Volt ................N/A DRAM Timing Page Enhance Data Transmitting.................Fast Enhance Addressing........................Fast T2 Dispatch...............................Enabled Clock Setting Fine Delay..................Listed Below CAS Latency Time (tCL)....................5 RAS# to CAS# Delay (tRCD).................5 RAS# Precharge (tRP)......................4 or 5 for Prime95 Precharge Delay (tRAS)....................9 or 15 for Prime95 All Precharge to Act......................4 REF to ACT Delay (tRFC)...................30 or 35 for Prime95 Performance Level.........................7 or 8 for Prime95 Read Delay Phase Adjust...................Listed Below MCH ODT Latency...........................Auto Write to PRE Delay (tWR)..................10 Rank Write to Read (tWTR).................10 ACT to ACT Delay (tRRD)...................3 Read to Write Delay (tRDWR)...............8 Ranks Write to Write (tWRWR)..............4 Ranks Read to Read (tRDRD)................5 Ranks Write to Read (tWRRD)...............4 Read CAS# Precharge (tRTP)................3 ALL PRE to Refresh........................4 Read Delay Phase Adjust Page Channel 1 Phase 0 Pull-In.................Enabled Channel 1 Phase 1 Pull-In.................Enabled Channel 1 Phase 2 Pull-In.................Enabled Channel 1 Phase 3 Pull-In.................Enabled Channel 1 Phase 4 Pull-In.................Enabled Channel 2 Phase 0 Pull-In.................Enabled Channel 2 Phase 1 Pull-In.................Auto Channel 2 Phase 2 Pull-In.................Enabled Channel 2 Phase 3 Pull-In.................Enabled Channel 2 Phase 4 Pull-In.................Enabled Clock Setting Fine Delay Page Ch1 Clock Crossing Setting................More Aggressive Ch2 Clock Crossing Setting................More Aggressive Ch1Ch2 CommonClock Setting................More Aggressive Ch1 RDCAS GNT-Chip Delay..................Auto Ch1 WRCAS GNT-Chip Delay..................Auto Ch1 Command to CS Delay...................Auto Ch2 RDCAS GNT-Chip Delay..................Auto Ch2 WRCAS GNT-Chip Delay..................Auto Ch2 Command to CS Delay...................Auto
Reply With Quote
Originally Posted by Dede99
1240mhz@2.02v 
since they look very good inside my RIG!
Bookmarks