The Maximus Formula Thread - Help/OCing/Guide/Rampage conversion

[icecpu]

This is my setting for now , and it does boot , I'm testing the ram now , but maybe sometime it hang at DET DRAM again , just pray now

Extreme Tweaker
Ai Overclock Tuner : Manual
OC From CPU Level Up : AUTO
CPU Ratio Control : Manual
- Ratio CMOS Setting : 9
FSB Frequency : 465
FSB Strap to North Bridge : 333
PCI-E Frequency: 105
DRAM Frequency: DDR2-1109
DRAM Command Rate : 2T
DRAM Timing Control: Auto
CAS# Latency : 5
RAS# to CAS# Delay : 5
RAS# Precharge : 5
RAS# ActivateTime : 18
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time : AUTO
Write Recovery Time : AUTO
Read to Precharge Time : AUTO

Read to Write Delay (S/D) : AUTO
Write to Read Delay (S) : AUTO
Write to Read Delay (D) : AUTO
Read to Read Delay (S) : AUTO
Read to Read Delay (D) : AUTO
Write to Write Delay (S) : AUTO
Write to Write Delay (D) : AUTO
DRAM Static Read Control: Auto
Ai Clock Twister : Auto
Transaction Booster : disabled
Relax level: 0

CPU Voltage : 1.4312
CPU PLL Voltage : AUTO
North Bridge Voltage : 1.51
DRAM Voltage : 2.20
FSB Termination Voltage : 1.50
South Bridge Voltage : 1.050
Loadline Calibration : Enabled
CPU GTL Reference : 0.63X
North Bridge GTL Reference : 0.67X
DDR2 Channel A REF Voltage : AUTO
DDR2 Channel B REF Voltage : AUTO
DDR2 Controller REF Voltage : DDR2-REFF
SB 1.5V Voltage : 1.5

[binormalkilla]

This is my setting for now , and it does boot , I'm testing the ram now , but maybe sometime it hang at DET DRAM again , just pray now

Extreme Tweaker
Ai Overclock Tuner : Manual
OC From CPU Level Up : AUTO
CPU Ratio Control : Manual
- Ratio CMOS Setting : 9
FSB Frequency : 465
FSB Strap to North Bridge : 333
PCI-E Frequency: 105
DRAM Frequency: DDR2-1109
DRAM Command Rate : 2T
DRAM Timing Control: Auto
CAS# Latency : 5
RAS# to CAS# Delay : 5
RAS# Precharge : 5
RAS# ActivateTime : 18
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time : AUTO
Write Recovery Time : AUTO
Read to Precharge Time : AUTO

Read to Write Delay (S/D) : AUTO
Write to Read Delay (S) : AUTO
Write to Read Delay (D) : AUTO
Read to Read Delay (S) : AUTO
Read to Read Delay (D) : AUTO
Write to Write Delay (S) : AUTO
Write to Write Delay (D) : AUTO
DRAM Static Read Control: Auto
Ai Clock Twister : Auto
Transaction Booster : disabled
Relax level: 0

CPU Voltage : 1.4312
CPU PLL Voltage : AUTO
North Bridge Voltage : 1.51
DRAM Voltage : 2.20
FSB Termination Voltage : 1.50
South Bridge Voltage : 1.050
Loadline Calibration : Enabled
CPU GTL Reference : 0.63X
North Bridge GTL Reference : 0.67X
DDR2 Channel A REF Voltage : AUTO
DDR2 Channel B REF Voltage : AUTO
DDR2 Controller REF Voltage : DDR2-REFF
SB 1.5V Voltage : 1.5

Try setting the trans booster relax level to 1 or increasing the NBV. You need to turn the DRAM voltage down to 2.16-2.18 because the board overvolts it. On mine I get 2.22V when I set it to 2.18V. I used to run Ballistix, and they're known to die from overvolting.....so you want to be careful.
You should be able to run 5-5-5-15 4 42 6 4 secondary 8 3 5 4 6 4 6 @ 2.18V (for now, might want to bump down to 2.16V 24/7)
Take the NBV up to 1.65V just for now, as you can test lower settings after you're stable. Just make sure that the temps stay around 45C and you're fine.