**Official DFI LanParty UT P35-T2R Review/Overclock/Guide Thread**

[Darkmind]

I can tell you, just fine.

Fill a brother in homie lol. I'm building a new water cooled unit based on a CM stacker 830 Evo, DFI LP UT P35-T2R, Q9450 (planned), so on so on.

[Brother Esau]

So much for "DFI doesn't make good intel boards". I can't recall exactly who but i read that quote more then once in this forum not too many months ago.

Bite yer tongue The P35 is the Intel Expert Board

[mad_skills]

Fill a brother in homie lol. I'm building a new water cooled unit based on a CM stacker 830 Evo, DFI LP UT P35-T2R, Q9450 (planned), so on so on.

What do you want to be filled about? You've got 125pages and ~3100 posts so get to work....
Seriously, what do you need?

[jimmyz]

Fill a brother in homie lol. I'm building a new water cooled unit based on a CM stacker 830 Evo, DFI LP UT P35-T2R, Q9450 (planned), so on so on.

I am using a qx 9650 right now. it is absolutely stable on this board with the latest beta bios. earlier bios's had some issues.

[mrcape]

heh, decided to do the copper plate and transpiper out the back but flipped the elbowed heatpipe to leave clearance for a fan. I love how physically configurable the that part of the board is.

Booted up first time no problem. I'm not sure if the bios temps are accurate, but this is what I have on stock everything in bios -

CPU Core - 16C
PWM - 39C
Chipset - 37C

Does that seem right for idling in the bios with stock bios/settings?

[mad_skills]

Use CoreTemp. What are your ambiental temps?

[Darkmind]

What do you want to be filled about? You've got 125pages and ~3100 posts so get to work....
Seriously, what do you need?

Incoming PM as this discussion may be long and run off topic at some point, as to not thread jack.

[mrcape]

Use CoreTemp. What are your ambiental temps?

I will as soon as I install windoze. My ambients are pretty cold plus I have the case open and some mega san ace fans blowing through ultra 120 and out top and back.

[mad_skills]

I will as soon as I install windoze. My ambients are pretty cold plus I have the case open and some mega san ace fans blowing through ultra 120 and out top and back.

Then i guess they are all right. But as the cpu temps can't be lower than ambiental than i assume your room is very cold.

[ultimeus]

Here they are:

I appreciate man, I have quite same settings but can't reach to 4 ghz, my max screenable is 3.8ghz

[nzbleach]

he just has a fine piece of silicone thats all.

[mad_skills]

he just has a fine piece of silicone thats all.

Ain't that what we all seek....

[C-N]

Ain't that what we all seek....

Every man to his own an all but I prefer the real thing lol

[ultimeus]

never say never, I give more volts an TADA 4 ghz

[Seanie's Show]

Is it just me or has anyone elese noticed since 12/24 bios, smart guardian is much more accurate, voltages are still out, but the temps are bang on.

[mad_skills]

Every man to his own an all but I prefer the real thing lol

What do you mean by the real thing?

never say never, I give more volts an TADA 4 ghz

That is too much vcore on quad for 24/7 usage.

[Praz]

That is too much vcore on quad for 24/7 usage.

LOL. From the looks of that screenshot it's not stable enough to use anyway.

[mad_skills]

LOL. From the looks of that screenshot it's not stable enough to use anyway.

I think even 1.55V is too much for Kentsfield on 24/7 basis, perhaps only on liquid cooling it's safe, on air i don't think so.

[WoZZeR999]

I had just bought the LT version of the board, and saw that the transpiper can be bought separately. Does the PWM area get warm on the LT version if there's an exhust fan right by it?

Also, if I'm using a 6750 for now, is the latest beta bios stable, or should I go for the latest official?

[mad_skills]

I had just bought the LT version of the board, and saw that the transpiper can be bought separately. Does the PWM area get warm on the LT version if there's an exhust fan right by it?

Also, if I'm using a 6750 for now, is the latest beta bios stable, or should I go for the latest official?

If your case has enough air inside circulating, you'll be ok.
Use either 10/05 beta or 12/24 official.

[ultimeus]

I think even 1.55V is too much for Kentsfield on 24/7 basis, perhaps only on liquid cooling it's safe, on air i don't think so.

Yes I know it's not stable it was just for me, I can't even do a 3dmar06 @ 4 ghz.

My daily setting is 3.6 ghz @ 1.4V

[WoZZeR999]

I've been trying to read all 124 pages, but I only have so many hours a day that I can sit down and read through all of the pages. I'm exited to get my board, ans my P5K is becoming a P0S. What is the standard droop on this board with and without Vdampner enabled, I have as much to .06v droop without the droop mod.

[mad_skills]

Yes I know it's not stable it was just for me, I can't even do a 3dmar06 @ 4 ghz.

My daily setting is 3.6 ghz @ 1.4V

That is more than enough quad core cpu power for any tasking.

[WoZZeR999]

If your case has enough air inside circulating, you'll be ok.
Use either 10/05 beta or 12/24 official.

Also, do the chips around the HS, where there isn't anything on top get hot as well? Do you think it would help if I used ramsink on the additional PWM resisters and chips around the CPU area?

[Weelkoo]

Hi guys!

I recieved sample of RETAIL E8200 BOX for review and I have small problem because I'm loosing stability near FSB 500MHz (1:1 divider). No matter what votages I set (PLL/VTT/NB/SB) the platform is crashing during SPI (NON EXACT IN ROUND) or Orthos Blend/Large FFT so it seems to be memory problem (playing with GLT doesn/t help at all). But - this particular memory kit (2x1GB OCZ Alpha PC-8000 CL4) is working well with ~600MHz CL5 at lower FSB. What's more VTT Voltage is way lower than I set in BIOS - f.e. 1,2V in BIOS = 1.12V measured, 1.6V in BIOS = 1,38V measured. BIOS DC24 and DB07. Quick try - CPU is booting into OS with FSB 530MHz...

Now I put my E6600 and at FSB 500MHz it's stable with only 1,41V on NB and 1,3V VTT (first try, so maybe it's stable with lower voltages also - but I think it's quite good as this CPU has FSB Wall at 520MHz). VTT set in BIOS is almost exact to measured VTT.

Do You have any ideas how to solve this problem? Or is it just FSB Wall?

PS. Forgive me my english as I'm self-educated in this language.