CellShock DDR3-1800 8-7-6-21 Testing!

[SeLecT]

Has anybody seen a Performance Level = 4 (my latest archivement) on them yet?....

http://www.hipro-tech.com/images/hip..._860_990_1.png

Rams are at 1T like Memset shows but cpu-z 1.42 can't track them.....Though V. 1.41 works just fine...

.

Great!

When i try to use PL = 5 my system will freeze But i will test it in the enext days

Here another 32M-Run by me with 4150Mhz, but my CPU is at the limit with watercooling...

11.40.672 / SeLecT / E6850 / Intel / 4158MHz / 1.598v / Gigabyte P35T DQ6 / 2x1024MB Cellshock DDR31800 @ 924Mhz 7-6-5-15 / Wakü

[hipro5]

Volts?

I always work them at 2.35Volts....and (if I remember right) 1.91V VMCH.....

[BenchZowner]

I haven't played a lot ( had some issues again ) but the lowest Performance Level I've got was Performance Level 2 with 200MHz Strap, and low FSB although.
At higher frequencies like the tested ones I'm usually at PL6.
I haven't tried more than 1.75V yet on the MCH, had no time to play...gotta finish all these reviews that should already been done

[metro.cl]

I always work them at 2.35Volts....and (if I remember right) 1.91V VMCH.....

Who should i believe? CPU-Z right? because if not those are some high volts for Memset MHz on RAM.

I'll upload some tests of a kit i have here that is pretty good i'm 100% sure im chipset limited, im at 1.81v only couse the NB goes crazy hot.

[saaya]

for memspeed, yeah, trust cpuz or setfsb.
if your nb gets so hot then why dont you add another fan or change the nb heatsink? :P

[SeLecT]

my latest results:


1M:

11.516s / SeLecT / Intel C2D E6850 @ 4374Mhz / 486*9 / VCore @ 1.776V / 2x1GB Cellshock DDR3-1800 @ 972 MHz 7-6-5-15 (2T) @ 2,14 V / Gigabyte P35T-DQ6 / Wakü /




32M:

11m 31.312s / SeLecT / Intel C2D E6850 @ 4205Mhz / 467*9 / VCore @ 1.776V / 2x1GB Cellshock DDR3-1800 @ 934 MHz 7-6-5-15 (2T) @ 2,14 V / Gigabyte P35T-DQ6 / Wakü /

[metro.cl]

for memspeed, yeah, trust cpuz or setfsb.
if your nb gets so hot then why dont you add another fan or change the nb heatsink? :P

Removing NB fan is taking SB fan also and i dont have a good replacement, plus i have to return the Maximus Extreme

I do have a fan on it but it's NB cooling is not so good

[saaya]

hmmmm well dont you have any deltas?

[camouflage]

Got a nice forward boost in 32M ranking with this RAM......... :

http://www.xtremesystems.org/forums/...d.php?t=122098

[metro.cl]

hmmmm well dont you have any deltas?

No deltas for sale here, i got a silverston 120x120 but is over the VGA pushing air but temps are still close to 50ºC maybe is the TIM that sucsks

[saaya]

Got a nice forward boost in 32M ranking with this RAM......... :

http://www.xtremesystems.org/forums/...d.php?t=122098

nice!

metro, on the maximus board?
yeah, the thermal compound there sucks... the heatsink is glued to the nb ihs with some strange thermal glue. one guy at oc team denmark dropped his board 5cm to the table and the waterblock heatsink just popped off

and some other people reported the waterblock popped off quite easily too and the thermal glue was spread very badly, so there was bad contact.

can you replace the thermal glue and put thermal paste?
If yes then do it, and you should look for a thick 40 or 50mm delta on ebay
they call them "screamers" for a reason but they are unbeatable when it comes to nb cooling

[BenchZowner]

I have a "crush" with these for NB cooling ( or just small spot cooling ):



Geez, you remember GlobalWin guys ?

AFAIR this was a Delta OEM fan for GW...it's a little...whiner... ~7700RPM and...lots of CFM

---p.s. more testing will take place today

[camouflage]

Little update now - 1T stable 7-6-5-15 at 950 Mhz:



Nice to see DDR3-1900 1T finally.........

[camouflage]

956MHz 1T stable at 7-6-5-15 :



Maybe I should try to break 11 min.

[SeLecT]

Use CopyWaza and you will break the 11min

Nice time btw!

[camouflage]

Use CopyWaza and you will break the 11min

Nice time btw!

Yep - think it's time to give it a try..............

[saaya]

very nice camou!
what vdimm?

[camouflage]

very nice camou!
what vdimm?

Up to 950 MHz 2.16 - 956 needs 2.18.

OT: I still do not have any money from the little sucker bought my prommy - do You remember? Went bankrupt and spending some time in jail yet - there is still nothing to get out of his pockets.........

SRY for OT.........

[railmeat]

"956MHz 1T stable at 7-6-5-15"

stable as in 32m pi is nice,but any prime or occt screenies?nice setup btw.

ps
camo,watch your sig,no links are allowed anymore in anyones sigs...

[Infa]

To achieve 956Mhz you have to get the cpu to 4.3Ghz, i hardly think his cpu are stable at that speed, the mem are surely stable, but not the cpu, so no Prime there i think... just wait until Wolfdale, then you will see 956+ stable of people/us

regards.

[camouflage]

"956MHz 1T stable at 7-6-5-15"

ps
camo,watch your sig,no links are allowed anymore in anyones sigs...

Thx - just deleted it. Didn't know about...........

[saaya]

Up to 950 MHz 2.16 - 956 needs 2.18.

OT: I still do not have any money from the little sucker bought my prommy - do You remember? Went bankrupt and spending some time in jail yet - there is still nothing to get out of his pockets.........

SRY for OT.........

yeah, i asked around but nobody heard from him again... :/

[BenchZowner]

Finally decided on what to do with the round-up, and started the main tests today.

Here are some findings for this kit:

Mainboard: Asus P5K3 Deluxe ( BIOS 0810 )

Tightest stable timings for DDR3-1800 1.8V ( Stock Main Timings & Freq ):
[ in BIOS order ]
1T Command Rate
8-7-6-21-1-48-4-4-1-E-D-E(0)

Tightest stable timings for max 5-5-4-15 tests @ 2.25V & DDR3-1535:
[ in BIOS Order ]
1T Command Rate
5-5-4-15-1-36-3-4-1-E-D-E(0)

[SeLecT]

Just a small 4Gig-test with Cellshock. More will come in the next days. It is on WinXP 64bit. I will test with Vista too, but not in the christmas time!

4096 MB Cellshock DDR3-1800 @ 800Mhz @ 7-6-5-15 @ 1,97V (maybe they run with lower voltage.... i will test it )

Merry Christmas!

[saaya]

what vmch?