ASUS Maximus Formula SE

[safan80]

Son of a..

430x9 unstable
435x9 unstable
440x9 unstable

Could have been my backup power supply causing these problem? because right now the Antec is getting replaced for a 3rd time because it can't power my 8800GTX, so I'm using a older power supply, a 680W

what voiltages in the bios are you using? Also are you running the beta occt? prime stable doesn't mean a thing with this board.

[Warboy]

what voiltages in the bios are you using? Also are you running the beta occt? prime stable doesn't mean a thing with this board.

I'm running beta OCCT, I can't get anything stable in it, no matter what.

right now I'm using

Extreme Tweaker
Ai Overclock Tuner : Manual
OC From CPU Level Up : AUTO
CPU Ratio Control : Manual
- Ratio CMOS Setting : 9
FSB Frequency : 430
FSB Strap to North Bridge : AUTO
PCI-E Frequency: 100
DRAM Frequency: DDR2-1033
DRAM Command Rate : 2T
DRAM Timing Control: Auto
DRAM Static Read Control: AUTO
Ai Clock Twister : Strong
Transaction Booster : AUTO

CPU Voltage : 1.550
CPU PLL Voltage : 1.60
North Bridge Voltage : 1.65
DRAM Voltage : 2.22
FSB Termination Voltage : 1.50
South Bridge Voltage : AUTO
Loadline Calibration : Enabled
CPU GTL Reference : x67
North Bridge GTL Reference : x67
DDR2 Channel A REF Voltage : AUTO
DDR2 Channel B REF Voltage : AUTO
DDR2 Controller REF Voltage : AUTO
SB 1.5V Voltage : AUTO

NB LED Selection : NB Volt
SB LED Selection : SB Volt
CPU LED Selection : CPU VOlt
Voltiminder LED : Disabled

CPU Spread Spectrum : Disabled
PCIE Spread Spectrum : Disabled

Advanced CPU Configuration
CPU Ratio Control : Manual
- Ratio CMOS Setting : 9
C1E Suppport : Disabled
CPU TM Function : Disabled
Vanderpool Technology : Disabled
Execute Disable Bit : Disabled
Max CPUID Value Limit : Disabled

[safan80]

I'm running beta OCCT, I can't get anything stable in it, no matter what.

right now I'm using

Extreme Tweaker
Ai Overclock Tuner : Manual
OC From CPU Level Up : AUTO
CPU Ratio Control : Manual
- Ratio CMOS Setting : 9
FSB Frequency : 430
FSB Strap to North Bridge : AUTO
PCI-E Frequency: 100
DRAM Frequency: DDR2-1033
DRAM Command Rate : 2T
DRAM Timing Control: Auto
DRAM Static Read Control: AUTO
Ai Clock Twister : Strong
Transaction Booster : AUTO

CPU Voltage : 1.550
CPU PLL Voltage : 1.60
North Bridge Voltage : 1.65
DRAM Voltage : 2.22
FSB Termination Voltage : 1.50
South Bridge Voltage : AUTO
Loadline Calibration : Enabled
CPU GTL Reference : x67
North Bridge GTL Reference : x67
DDR2 Channel A REF Voltage : AUTO
DDR2 Channel B REF Voltage : AUTO
DDR2 Controller REF Voltage : AUTO
SB 1.5V Voltage : AUTO

NB LED Selection : NB Volt
SB LED Selection : SB Volt
CPU LED Selection : CPU VOlt
Voltiminder LED : Disabled

CPU Spread Spectrum : Disabled
PCIE Spread Spectrum : Disabled

Advanced CPU Configuration
CPU Ratio Control : Manual
- Ratio CMOS Setting : 9
C1E Suppport : Disabled
CPU TM Function : Disabled
Vanderpool Technology : Disabled
Execute Disable Bit : Disabled
Max CPUID Value Limit : Disabled

if your getting error code 1 in occt you need to up the vcore.

[Warboy]

if your getting error code 1 in occt you need to up the vcore.

I'm not getting a error code I'm getting lockups and reboots

[dennismagic]

I'm not getting a error code I'm getting lockups and reboots

DRAM Static Read Control: AUTO
Ai Clock Twister : Strong
Transaction Booster : AUTO

try to disable or lower the above setting to see any improvement !

[dMITIj]

DRAM Static Read Control: AUTO
Ai Clock Twister : Strong
Transaction Booster : AUTO

try to disable or lower the above setting to see any improvement !

In your sig your REV i wrong... 802 is the BIOS number the REV will be 1.02g ore 1.03g

[Malik]

I have question about this function. When i change from peg/pci to pci/peg - my video card dont load, but the system is runing - why ?
For what is this function, and how i must set this ?