Gettin started on Wc build ( 56k beware )

**Waterlogged** · 11-09-2007, 10:10 PM

Thanks for the link disruptfam.

Tells me half of what I need to know before buying. Now, just need to wait for you to get your SM's and tell us what you think.

**disruptfam** · 11-09-2007, 10:32 PM

Originally Posted by Waterlogged

Thanks for the link disruptfam.

Tells me half of what I need to know before buying. Now, just need to wait for you to get your SM's and tell us what you think.

yeah mate... I'll be getting my gear early next wk petra sent out my order 2day...

Update ya then

**asterix34** · 11-12-2007, 02:41 AM

Sexy case,great work ı want to continue.

**disruptfam** · 11-12-2007, 06:32 AM

Originally Posted by asterix34

Sexy case,great work ı want to continue.

cheers mate more update's this week..when i get my petra order...

**disruptfam** · 11-12-2007, 07:38 PM

update!!!

Got my Petra order 2day...check it out.....

Was looking forward to getting this beauty !!

Eddy i commend you on this beautiful block!!

Scythe's new slip stream series fan...

good ol yate loon d12sm _12

Wanted to test this against my new scythe ultra's kazes and scythe slip stream fan's

scythe fan's i got from petra... 2 x 80mm and 1 slip stream...

That all for now fellaz

Will be mounting gpu loop block next.... finishing drilling/cutting case etc....and testing fan's More pic's to come soon...

ENJOY!!!

**rbsmontemor** · 11-12-2007, 07:59 PM

Your project makes mine looks like shi* hahaha.

Congratz...can't wait to see that box finished

Rbs.

**disruptfam** · 11-12-2007, 08:07 PM

Originally Posted by rbsmontemor

Your project makes mine looks like shi* hahaha.

Congratz...can't wait to see that box finished

Rbs.

lol that's not my aim with my build.... none of our rig's are shi...

thanks mate hopefully be finished in a week or so.....

**disruptfam** · 11-12-2007, 08:16 PM

question fellaz:

with the mounting if the ek block... i put the o-ring then distancer than barb? is that correct???

and the un-used hole's i put the plug in???

don't want to mount it incorrectly

cheers guys

**disruptfam** · 11-12-2007, 08:52 PM

ok mounted the ek block... took about 45mins lol very fiddly....abit of pita really but it looks great... post pic's soon

cheers

**Waterlogged** · 11-12-2007, 10:44 PM

I don't care 'bout no stinkin' EK block!

I don't care 'bout no stinkin' slipstream fans!

I don't care 'bout no stinkin' 80mm fans either!

I want test results comparing the YL to the Ultra Kaze's....NOW DAMMIT!

**Jedda** · 11-13-2007, 02:53 AM

Barbs on copper side = no spacer.
Barbs on delrin or acrylic side = use spacer. Spacer o-ring seals to block, barb 0-ring seals to spacer.
What you're doing is ensuring the barbs' threads don't protrude into the water chamber. So everything depends on what barbs are used and where.
Bloody amazing how fast Quoc can get stuff to us in Oz. Faster than many locals do.

**Patriote** · 11-13-2007, 05:55 AM

Awesome

Waiting for pics!

BTW: I told ya! Those block are a bit of a pita to hook on a 8800GTX.

**Jedda** · 11-13-2007, 06:06 AM

Originally Posted by Patriote

Awesome

Waiting for pics!

BTW: I told ya! Those block are a bit of a pita to hook on a 8800GTX.

Trick seems to be not over-tightening the outer screws.
I got a much better mount second time round, after getting a good look at the first's TIM distribution.

**disruptfam** · 11-13-2007, 06:33 AM

Originally Posted by Waterlogged

I don't care 'bout no stinkin' EK block!

I don't care 'bout no stinkin' slipstream fans!

I don't care 'bout no stinkin' 80mm fans either!

I want test results comparing the YL to the Ultra Kaze's....NOW DAMMIT!

Patience mate patience will test them 2morow morning for you!

**disruptfam** · 11-13-2007, 06:35 AM

Originally Posted by Jedda

Barbs on copper side = no spacer.
Barbs on delrin or acrylic side = use spacer. Spacer o-ring seals to block, barb 0-ring seals to spacer.
What you're doing is ensuring the barbs' threads don't protrude into the water chamber. So everything depends on what barbs are used and where.
Bloody amazing how fast Quoc can get stuff to us in Oz. Faster than many locals do.

cheers mate cleared that up for me.... had the spacer both side's lol will fix...
Yeah Petra is awesome ordered Friday got Tuesday... now that's service!!!

Thanks guys @ Petra's!!!

EDIT: fixed the block... will take off 2morow to check tim distribution then back on again

**disruptfam** · 11-13-2007, 06:37 AM

Originally Posted by Patriote

Awesome

Waiting for pics!

BTW: I told ya! Those block are a bit of a pita to hook on a 8800GTX.

Cheers mate...

more pic's soon!!!

**disruptfam** · 11-13-2007, 07:58 AM

Pre-min fan result's

Fan's tested

Yate loon D12SM-12 33dba 70cfm
Scythe slip stream 33dba 88cfm
Scythe ultra kazes 32.91dba 87cfm
Xurillian fan 32dba 70cfm

D12SM: the quietest @ high,med and low out the 4 fan's tested pushes more than the Xurillian but less than the scythe's... surprised how quiet it was

Xurillian: Pushes the least air, @ all setting's has annoying rattling noise @ all setting's
Scythe slip stream: Pushes more air than the d12sm and xurillian @ all setting's Inaudible @ low very quiet @ med and noticeable but not to bad @ high
Scythe ultra kasez: Pushes equal or a tad more compared to slip stream inaudible @ low quiet @ med Pushed most air , loudest out all four fan's tested @ high.... by a fair bit slight whining noise and rattling noise (might be faulty fan will test another 1 to be sure)

Results after a very quick test... looks like a 3 horse race here d12sm,slip stream and scythe ultra kaze more to continue tomorrow

**Waterlogged** · 11-13-2007, 10:53 AM

Originally Posted by disruptfam

Patience mate patience will test them 2morow morning for you!

You do know I was just messing with you...right?

Originally Posted by disruptfam

...Yeah Petra is awesome ordered Friday got Tuesday... now that's service!!!

I wish ground was that fast.

I ordered last Thursday and won't get mine until this Thursday. If I order UPS ground from anyone else, I get it in 3 days. I'm not spending another ~$8-9 (I can't afford) to get my stuff 2 days faster. This is about the only area I see that Petra needs to improve upon.

Originally Posted by disruptfam

Pre-min fan result's

Fan's tested

Yate loon D12SM-12 33dba 70cfm
Scythe slip stream 33dba 88cfm
Scythe ultra kazes 32.91dba 87cfm
Xurillian fan 32dba 70cfm

D12SM: the quietest @ high,med and low out the 4 fan's tested pushes more than the Xurillian but less than the scythe's... surprised how quiet it was

Xurillian: Pushes the least air, @ all setting's has annoying rattling noise @ all setting's
Scythe slip stream: Pushes more air than the d12sm and xurillian @ all setting's Inaudible @ low very quiet @ med and noticeable but not to bad @ high
Scythe ultra kasez: Pushes equal or a tad more compared to slip stream inaudible @ low quiet @ med Pushed most air , loudest out all four fan's tested @ high.... by a fair bit slight whining noise and rattling noise (might be faulty fan will test another 1 to be sure)

Results after a very quick test... looks like a 3 horse race here d12sm,slip stream and scythe ultra kaze more to continue tomorrow

Hmm, from these results, it looks like I stay with the SM's. I'll wait for full results before deciding for certain though.

**disruptfam** · 11-13-2007, 05:09 PM

SMALL UPDATE:

Mounted ek block got and got my d-tek fitting and alot of tubing!! 25ft to be exact

25ft of masterkleer so cheap

that all for now...

Next fan result's and modding of my v2000 case enjoy!!!

**Jedda** · 11-13-2007, 05:34 PM

You know its just a couple of drill holes and some filing to make your own single slot end plate.
I bought one in a pile of stuff but its very easy to make from a spare blanking plate.

**Nate P.** · 11-13-2007, 05:36 PM

25ft on tubing...

**Patriote** · 11-13-2007, 06:13 PM

Originally Posted by Nate P.

25ft on tubing...

So what? I have 60ft of different Brand\sized Tubing for my XETM Project! ROFL

But Hey, Small question m8, you actually used the kinda metal O-ring (Which include a black plastic O-ring) right? What is it used for? Protecting the Acrylic from cracking when mounting the barbs on the acrylic side of the block?

I didn't used them on my past loop. Did i do wrong?

**Nate P.** · 11-13-2007, 06:23 PM

Originally Posted by Patriote

So what? I have 60ft of different Brand\sized Tubing for my XETM Project! ROFL

No no, just envious...

**disruptfam** · 11-13-2007, 06:29 PM

Originally Posted by Patriote

So what? I have 60ft of different Brand\sized Tubing for my XETM Project! ROFL

But Hey, Small question m8, you actually used the kinda metal O-ring (Which include a black plastic O-ring) right? What is it used for? Protecting the Acrylic from cracking when mounting the barbs on the acrylic side of the block?

I didn't used them on my past loop. Did i do wrong?

Yes i did use it.... As jedda explained beforehand...

Barbs on copper side = no spacer.
Barbs on delrin or acrylic side = use spacer. Spacer o-ring seals to block, barb 0-ring seals to spacer.
What you're doing is ensuring the barbs' threads don't protrude into the water chamber. So everything depends on what barbs are used and where.

I didn't know this would turn into who's the got the biggest/most tubing competition hahahaha

**shazza** · 11-13-2007, 06:56 PM

Good stuff, disruptfam ... am enjoying your progress and looking forward to the pics when you load everything in the case.

Thread: Gettin started on Wc build ( 56k beware )

Thread Tools

Search Thread

Rate This Thread

Display

Bookmarks

Bookmarks

Posting Permissions