D-tek nozzles

**IanY** · 10-19-2007, 04:25 PM

Well, its been two days, and its still under 2 C. Of course, in the NY area, its a wet, humid and unseasonably stuffy night.

Anyone else has quad nozzle findings to report, no matter how preliminary ?

**nimrod_o** · 10-20-2007, 09:25 AM

Just initial impression,
I added the q6600 nozzle and the gasket supplied between the middle and upper plates.
I also added a NB swifty water block and a crappy MIPS Mosfet block to my loop on my IP-35.
But even with the increased restriction from added blocks (which by the way are coming out - due to very bad performance from the MIPS mosfet block) - I am still getting 2 degrees lower on my CPU under load. (I would also like to mention that the ambient temp have increased this week in my country - only to strengthen the validity of result.)
This is by no means a through test...just my individual findings.
This result was consistent on 3 different mountings.

iadstudio · 10-20-2007, 10:12 AM

I didn't install it, but the 3.5 nozzle for the dual cores looks awfly narrow. I don't doubt the results, but it's just hard for me to imagine that it doesn't cause serious restriction. I guess spray plpacement and turbulance has a greater effect than I thought.

I'll post my results this weekend. Sorry I don't have a quad to test with.

**pak** · 10-20-2007, 10:24 AM

Has anyone tried putting a non quad nozzle on a quad?

--pak

**Talonman** · 10-20-2007, 12:01 PM

Well you are all going to be jealous, but when I ordered my D-tek Fusion, 5 Scythe fans, and 10' 1/2" Tygon hose from Petra, I received a blue pen, and a hand made PTS Monster!!

There was a note that he was guarding my fans during shipping, and that he probably would be hungry by the time he made it to my house...

Thanx Alex!

**Evil-Vincent** · 10-20-2007, 01:04 PM

I have a socket 939 3800x2 and I am busy with assembling watercooling, and I have a D-tek Fuzion. Will it work for that cpu too?

**rafrag** · 10-20-2007, 02:15 PM

Originally Posted by Talonman

Well you are all going to be jealous, but when I ordered my D-tek Fusion, 5 Scythe fans, and 10' 1/2" Tygon hose from Petra, I received a blue pen, and a hand made PTS Monster!!

There was a note that he was guarding my fans during shipping, and that he probably would be hungry by the time he made it to my house...

Thanx Alex!

pictures of the monster

please

**nealh** · 10-20-2007, 03:40 PM

Originally Posted by Talonman

Well you are all going to be jealous, but when I ordered my D-tek Fusion, 5 Scythe fans, and 10' 1/2" Tygon hose from Petra, I received a blue pen, and a hand made PTS Monster!!

There was a note that he was guarding my fans during shipping, and that he probably would be hungry by the time he made it to my house...

Thanx Alex!

Not fair ..Alex just taunted me with pens...............

**Talonman** · 10-20-2007, 04:17 PM

Originally Posted by rafrag

pictures of the monster

please

Ask, and you shall receive!!

I'm sure these are hard to come by too!!!

**rafrag** · 10-20-2007, 05:15 PM

Originally Posted by Talonman

Ask, and you shall receive!!

I'm sure these are hard to come by too!!!

turning green

**Lu523** · 10-20-2007, 05:50 PM

My FuZion and nozzels showed up today. So far I am seeing about a 2 C lower on idle and load. I am like some of the others , need to let the AS5 cure.
And as for PTS. They are the best. Their packing is top notch. Great service all the way around.

**step** · 10-21-2007, 08:42 AM

Haha that monster is a rort, someone has too much time on their hands! :P

**Martinm210** · 10-21-2007, 10:34 AM

Man...I've recieved several pens and notes, but that monster is cool!

**Talonman** · 10-21-2007, 10:56 AM

Well, I don't know if it was the PTS Monster, or just the killer selection of products, but I just placed another order with Petra's.....

I am now an official repeat customer.

**Monk0101** · 10-21-2007, 06:12 PM

I see that Petra is out of the nozzles again. Any idea when the next boat arrives?

iadstudio · 10-21-2007, 06:42 PM

say in stock for me.

**IanY** · 10-21-2007, 07:40 PM

Well, I don't see any more improvements over here. Maybe I need to remount once more? So far, my wife's cpu has gained 2 C and I think its plenty good... great.. Quad nozzle on a QX6700 at stock speed and stock voltage. System temp is still a tad high, but that's because its a "silent" type of computer and there's a general lack of good airflow.

**Monk0101** · 10-21-2007, 07:55 PM

Originally Posted by iadstudio

say in stock for me.

If you add it to your cart, is says "The D-Tek FuZion Accelerator Nozzle Kit is not currently available. Please contact us for availability of this item. "

**situman** · 10-21-2007, 08:40 PM

No improvement for me.

**IanY** · 10-21-2007, 08:41 PM

Originally Posted by situman

No improvement for me.

No.. as in absolutely none at all ? That's strange.. you have a Q6600 G0 right ? Maybe because you are already pushing it that hard with San Aces on full blast.

**Talonman** · 10-22-2007, 05:48 AM

Originally Posted by situman

No improvement for me.

Were you already running with an O-ring before installing the kit?

**Aldy402** · 10-22-2007, 06:32 AM

none for me either using quad nozzle and mx2

**IanY** · 10-22-2007, 06:33 AM

Originally Posted by Aldy402

none for me either using quad nozzle and mx2

You are getting no improvement as well ?

Maybe you MX2 users should allow some time to cure as well, contrary to what the specs say.

**Aldy402** · 10-22-2007, 06:55 AM

Originally Posted by IanY

You are getting no improvement as well ?

Maybe you MX2 users should allow some time to cure as well, contrary to what the specs say.

it's been about 48 hours and the temps are pretty much within 1-2c of each other between 4 mounts

**IanY** · 10-22-2007, 07:05 AM

Originally Posted by Aldy402

it's been about 48 hours and the temps are pretty much within 1-2c of each other between 4 mounts

Well, that's all you are going to see. There's got to be at least 1 C improvement.

Thread: D-tek nozzles

Thread Tools

Search Thread

Rate This Thread

Display

Bookmarks

Bookmarks

Posting Permissions