**Official DFI LanParty UT P35-T2R Review/Overclock/Guide Thread**

[Brother Esau]

Set Ram at 333/667 Divider and thata 1:1

[SmokeyTheBandit]

Well did a bit of testing but there sure is something special about the 10/5 bios compared to the 9/13 and it got something to do with the memory bandwith

Tested 9/13 bandwith in everest -> 9300 Mb/s
Tested 10/5 bandwith in everest -> 10080 Mb/s
This is done with exactly the same settings nothing changed apart from a bios flash

I'm keeping the 10/5 thats for sure

[Brother Esau]

oh yea huh

[emoners]

Well did a bit of testing but there sure is something special about the 10/5 bios compared to the 9/13 and it got something to do with the memory bandwith

Tested 9/13 bandwith in everest -> 9300 Mb/s
Tested 10/5 bandwith in everest -> 10080 Mb/s
This is done with exactly the same settings nothing changed apart from a bios flash

I'm keeping the 10/5 thats for sure

so the 10/05 beta is doing good?

[jimmyz]

oh yea huh

he may be right, I flashed the day i saw it and my rig seems smoother with 4-4-4-9 @1000but i don't remember what my everest numbers were for these settings before.

[Brother Esau]

I'm gonna flash now be back soon.......Muuh hhahahhh

[Cascades]

Hmmm.... What's the link for the 10/05 BIOS? I might as well give it a try

[emoners]

I'm gonna flash now be back soon.......Muuh hhahahhh

hahaha now that got me intrigued....might do so as well

[emoners]

Hmmm.... What's the link for the 10/05 BIOS? I might as well give it a try

http://www.dfi.com.tw/Support/Downlo...FLAG=B&SITE=US

[Cascades]

Thanks....

[emoners]

Just flashed the 10/05 bios via Windows, then in the middle of updating, the computer froze then suddenly reseted itself...now the Diagnostic LED shows C0 then C1 then stopped. Tried clearing CMOS & doing safe boot but nothing happens. Just C0 then C1

What should i do????

[Brother Esau]

I'm Back ....Well Flash went good but for me in Sandra no change in memory performance not even by a hair Too soon to say anything but will say whats what in a day or so

[emoners]

Just flashed the 10/05 bios via Windows, then in the middle of updating, the computer froze then suddenly reseted itself...now the Diagnostic LED shows C0 then C1 then stopped. Tried clearing CMOS & doing safe boot but nothing happens. Just C0 then C1

What should i do????

BUMP

[Brother Esau]

Just flashed the 10/05 bios via Windows, then in the middle of updating, the computer froze then suddenly reseted itself...now the Diagnostic LED shows C0 then C1 then stopped. Tried clearing CMOS & doing safe boot but nothing happens. Just C0 then C1

What should i do????

Why do people continue to use that sh*t program Win Flash? I swear if I had $10.00 for every time I have heard this crap over and over again and every single incident always revolves around people Flashing from Windows!

Sorry Kid bad news for sure maybe after this you will spend $6.00 and buy a Floppy drive and never Flash From WINDOWS AGAIN.......

[emoners]

sorry....so does that mean my board is dead?

[Brother Esau]

Probably Yes! Pull the Battery and place Clear C'mos Jumper in Clear Postion for 24 hrs // Replace in reverse order after 24hrs and use only a PS2 Keyboard Upon Power on Hold the Insert and Home Key down and maybe you may get lucky and it will clear it up!

[M3kk]

And try with just 1 memory stick.

[Brother Esau]

Whoops yea that too almost forgots....up wait I did forgets

[cuhaos]

along with doing battery/jumper, i suggest unplugging the power supply to totally cut power to the board. that method seems to revive the board from tons of bad stuff but im not sure about bad bios flashes

all you can do is try

[Brother Esau]

Well did a bit of testing but there sure is something special about the 10/5 bios compared to the 9/13 and it got something to do with the memory bandwith

Tested 9/13 bandwith in everest -> 9300 Mb/s
Tested 10/5 bandwith in everest -> 10080 Mb/s
This is done with exactly the same settings nothing changed apart from a bios flash

I'm keeping the 10/5 thats for sure

@SmokyTheBandit ....hey you have that Cooler Master Gemini in a Case or on the Bench? If in the Case how does it fair Blowing air on Motherboard being confined in case?

[Brother Esau]

along with doing battery/jumper, i suggest unplugging the power supply to totally cut power to the board. that method seems to revive the board from tons of bad stuff but im not sure about bad bios flashes

all you can do is try

I am assuming that goes without saying but better safe than sorry I suppose

Worst Case scenario you will have to buy a Bios Chip Flashed with 9/13/07 and replace the old one with the new But you will need a Bios Chip extractor tool along with the new chip. Don't contact DFI cuz you are on Beta Buddy and you know what that means.

[Brother Esau]

Bios is good so far! Heres a Suicide Run and too bad I'm a Starving White Man cuz Daddy needs some Water Cooling

[Brother Esau]

2MB SuperPi

[M3kk]

So its better than 913 ?

[Brother Esau]

Kinda hard to say Figuring this Board out is like opening a 3 lock Pandoras Box

First time I have gotten frisky with this chip got it up to 4170 and it BSOD Giddy Up!!!! So I am thinking with Phase Change and the desire to Blow Sh*t Up it will do beyond 4.1GHZ: