POST YOUR E6850 with OC PERFORMANCE

**M3kk** · 09-17-2007, 03:18 AM

4 Ghz @ 1.45 Orthos Air

**Infa** · 09-17-2007, 05:40 AM

I ALSO WANT those LOW VID bastards!

**Tuvok-LuR-** · 09-17-2007, 07:43 AM

E6850 SLA9U L724B056
422x9 (3800 Mhz) @ 1.5v
Aircooled Zalman CNPS 9700
Asus P5K-E - Cellshock Value PC5300
7h 23m Orthos Blend

**miesso** · 09-17-2007, 04:18 PM

is there any known temp-related bug with this cpu?
my temps are way too low...actually, at this very moment my cores idle @12 and 13°C (everest)...very strange for aircooling (Tt Beetle, max rpm)

(both logs were done under orthos)

**rge** · 09-17-2007, 07:12 PM

24/7 E6850 3.9 w/F6 1.475V bios
With my high ambient of 25C, and my ultra in my loop (found out it increases load temps 6-7C by temporarily unplugging power and using old video card), I think this is going to be my best for 24/7. Though did manage to decrease load temps permanently by 3-4C by adding push fans to my PA120.3 (nexus pull fans already maxed at 740-820 RPM, dang nexus fans with incorrect specs were supposed to be 1000rpms)

**HousERaT** · 09-17-2007, 07:26 PM

Cooled with a Tuniq Tower

**giorgos th.** · 10-14-2007, 05:07 AM

a quick 1m and 32m with 22C room temp and 1.67Vcore @ load.

**EfterlysT** · 10-14-2007, 11:27 PM

Orthos@4.2Ghz@1.56v

http://i18.photobucket.com/albums/b1...dat/orthos.jpg

Cooling: Modded Prometeia Mach

**eva2000** · 10-19-2007, 04:01 AM

My new 2nd hand purchased E6850 L720A489 on air!

System

Intel Core 2 Duo E6850 L720A489 Retail
Thermalright Ultra 120 Extreme + 120x38mm Panaflo 103cfm fan + Artic Cooling MX-2 TIM
Asus Blitz Formula 1101 bios
128MB Gainward FX5200 PCI
2x1GB Team 6400C3 Micron D9GMH in white dimm slots
Memory cooling = 120x25mm Thermaltake 81cfm fan
80GB Hitachi 7K80 SATA on Promise SATA300 TX4 PCI 32bit/66Mhz controller - to allow higher PCI-E frequency for 3dmark benching in the future.
Pioneer DVR-08 Burner
Sony FDD
620W Corsair HX620 PSU
WinXP Pro SP2

@3600Mhz at 1.312v load
Definitely, best core 2 duo cpu I have owned to date

**M3kk** · 10-19-2007, 04:07 AM

Try 3600 with lower vCore, or 3800 with this vCore

.

4000 MHZ Prime @ 1.392v @ watercooled

.

**~~emoners~~** · 10-19-2007, 04:17 AM

@M3kk: What's your VDIMM on that?

**M3kk** · 10-19-2007, 04:21 AM

2.2-2.3V i dont know exactly

.

**Machinus** · 10-22-2007, 08:44 PM

I thought my L725A was nice...but now I see there are 6850's hitting 4Ghz under 1.4v

What's the method for getting such low voltage performance?

**hotshot100** · 10-24-2007, 02:46 AM

L26
1.66250 vcore
24/24 7/7
watercooling max temp 56 idle temp 27

**lazy** · 10-28-2007, 09:56 AM

Originally Posted by M3kk

Try 3600 with lower vCore, or 3800 with this vCore

.

4000 MHZ Prime @ 1.392v @ watercooled

.

im sorry but, does cpu-z even report the correct voltage for the cpu?

**Garrett** · 10-28-2007, 10:11 AM

Yes 1.41 most certainly reports the actual (and correct) voltage

I gotta say, 4ghz with <1.4 vcore is very impressive

PS M3kk what stepping is that? and what waterblock or did I read over it...

**lazy** · 10-28-2007, 10:23 AM

Originally Posted by Garrett

Yes 1.41 most certainly reports the actual (and correct) voltage

I gotta say, 4ghz with <1.4 vcore is very impressive

PS M3kk what stepping is that? and what waterblock or did I read over it...

so im guessing its a vdroop problem for me then?

CPU-Z and UGuru reports about the same until i open a tab for the uguru, which then shows what i set on bios, which is 1.585 instead of the 1.55 being reported

**M3kk** · 10-28-2007, 10:49 AM

lazy, yet is is real. And yes, for you is a drop problem

. 1.55 is the ~real voltage.
Garrett, stepping G0, but you want to know the fpo

L720A745 , and Nexxxos XP block.

**Garrett** · 10-28-2007, 12:09 PM

Well I have a nexxxos xp block too, and a 9w laing pump complete with a pa120.3 with 6 fans push/pull but I'll never manage 40c stressed... more like 50c lol... unless it's very cold in your room lol...
I have the G0 too, L720A696 IIRC... did you lap your cpu or what

again: impressive job

**camouflage** · 10-29-2007, 05:05 AM

Originally Posted by Machinus

I thought my L725A was nice...but now I see there are 6850's hitting 4Ghz under 1.4v

What's the method for getting such low voltage performance?

Pick up a good chip..........:

**M3kk** · 10-29-2007, 05:18 AM

That screen is bull...

I can tun 3dmark06 cputest at 4000 mhz with 1.35v

.

**Zeus** · 10-29-2007, 06:22 AM

Originally Posted by Garrett

Well I have a nexxxos xp block too, and a 9w laing pump complete with a pa120.3 with 6 fans push/pull but I'll never manage 40c stressed... more like 50c lol... unless it's very cold in your room lol...
I have the G0 too, L720A696 IIRC... did you lap your cpu or what

again: impressive job

There's 3 reasons to this:

1) your pumping power is girly, get the DCC+
2) lap your cpu, don't bother trying to take off the IHS in a frying pan (lol)
3) M3kk is wearing 3 coats due to freezing ambiant temps, or is he?

Btw, Garrett, mines goes up to 48C load and it's a B2 on a PA 120.2 with 1.408V.

**M3kk** · 10-29-2007, 06:45 AM

Nope

.

The ambient temp was 15-20 oC, but near 20

.
I have an Eheim 1046 pump ( 300 L/h

, but 1.2M lift up and dead silent :P ), in the loop i have the VGA ( 7900GT @ 1.55v ), one unused chipset block, the nexxxos XP platinum block and the nexxxos extreme III radiator, with 2 coolers

.

**Garrett** · 10-30-2007, 08:30 AM

and a low VID chip too

1.2750v

Ah well tonight I'm gonna pick up the DDC+ pump and prepare my build further, in another PC71

PS M3kk did you or did you not lap that cpu?

**M3kk** · 10-30-2007, 10:15 AM

Nope, its out of box, without lapping and stuff.

Thread: POST YOUR E6850 with OC PERFORMANCE

Thread Tools

Search Thread

Rate This Thread

Display

Bookmarks

Bookmarks

Posting Permissions