my second email to asus h

This email has been forwared to Engineering.

Best Regards,

Rob T.
Level 3 Support Engineer
Asus Technology
Http://usa.asus.com
Phone: (812)-282-2787
RMA: (510)739-3777 opt. 2


Thank You for using our technical support deparment. Our goal is 100% customer satisfaction from our valued customers. Please take just a moment to fill out our customer service survey. With these results we can improve our customer satisfaction and provide you with better service on your next call. Thank you for taking your time to complete this survey.
http://sip.asus.com/Survey/Questionn...063023308.aspx



---------- Original Message ----------
From : @yahoo.com
Sent : 9/3/2007 1:04:10 AM
To : "tsd@asus.com.tw"
Subject : Motherboard L1N64-SLI WS



[CASEID=WTM20070903054247048]



Apply date : 9/3/2007 12:54:24 AM
[Contact Information]
*Name : carter
*Email Address : @yahoo.com
Phone Number :
City : ny
*Country : United States

[Product Information]
*Product Type : Motherboard
*Product Model : L1N64-SLI WS
*Product S/N :
Place of Purchase : NEWEGG
*Date of Purchase : 2007/7/1

[Motherboard Specification]
*Motherboard Revision : 1.01g
*Motherboard BIOS Revision : 0505

[VGA Card Specification]
*VGA Card Vendor : ati
*VGA Card Model : aiw ve
*VGA Card Chipset : radeon
*VGA Card Driver : 6.11

[CPU Specification]
*CPU Vendor : amd
*CPU Type : fx70
*CPU Speed : 2.6

[Memory Specification]
*Memory Vendor : crucial
*Memory Model : tracer 1066
*Memory Capacity :

[HDD Specification]
HDD Vendor :
HDD Model :
HDD Capacity :

[Add-on Card Specificatio]
Add-on Card Vendor :
Add-on Card Type :
Add-on Card Model :

*Operating System : WinXP

[Problem Description]
i was wonder for the next bios ver. can you add timings to adjust drive strengths on the memory . i
use a program called memset in windows but it only changes the timings for cpu 0 and not cpu 1 also.
also can you enable cool&quiet to work with other multipliers instead of must the stock one.

these are the timings that would be most helpful changeable at the bios level\


DRAM Configuration Settings:

Memclock Tri-Stating............. - Disabled
Memory Hole Remapping............ - Enabled
Auto Optimize Bottom IO.......... - Enabled

DRAM Drive Strength.............. - Level 12
RAM Drive Weak/Normal Mode....... - Auto
CLK Enable Drive Strength........ - Auto
Chip Select Drive Strength....... - Auto
MEM Address Drive Strength....... - Auto
MEM Clock Drive Strength......... - Auto
Memory Data Drive Strength....... - Auto
Data Strobe Drive Strength....... - Auto
CS/ODT Pin Fine Delay............ - Auto

SLI-Ready Memory................. - Disable
Timing Mode...................... - Manual
Memory Clock Value/Limit......... - 400Mhz
Command Per Clock (1/2T)......... - Enable
CAS Latency Control (Tcl)........ - 003 CLK
Min RAS Active Time (Tras)....... - 005 CLK
RAS to CAS Delay................. - 004 CLK
Row Precharge Time (Trp)......... - 003 CLK
RAS to RAS Delay (Trrd).......... - 003 CLK
Row Cycle Time (Trc)............. - 011 CLK
DIMM 1 Row Refresh (Trfc0)....... - Auto
DIMM 2 Row Refresh (Trfc1)....... - 105 ns
DIMM 3 Row Refresh (Trfc2)....... - Auto
DIMM 4 Row Refresh (Trfc3)....... - 075 ns
Read Precharge Time (Trtp)....... - 003 CLK
Write Recovery Time (Twr)........ - 005 CLK
Read to Write Delay (Trwt)....... - 004 CLK
Write to Read Delay (Twtr) ...... - 003 CLK
Refresh Period (Tref)............ - 03.9 us
Max Asynch Latency............... - 006 ns
Bank Interleave.................. - Enabled
DRAM On-Die Termination.......... - 075 ohm
Read Delay From Rx FIFO.......... - 2.5 CLK
Read/Write Queue bypass.......... - 08 time
Bypass Maximum................... - 04 time
32 Byte Granularity.............. - Auto
Idle Cycle Limit................. - 04
Dynamic Counter.................. - Enable
Read DQS Skew.................... - Auto


thank you so much for your time