POST YOUR E6850 with OC PERFORMANCE

[LivingL@rGe81]

Mines a L719B018 with a VID of 1.35v. Here's a few screenies..
Just can't hit the 4gig mark, think the motherboard might be holding me back!

Thats alot of volts mate I have that exact stepping & can bench at 4200Mhz with that voltage!!!!

Try tweaking your ram settings & giving your vMCH some more volts

By the way i'm using a Turiq Tower with a 60CFM sunon fan inside! Still building my watercooling loop

[TheGoat Eater]

What batch?

L719B095

[michaLcoughliN]

I tried last nigt @ 4ghz with 1.55vcore.. failed withing 5 seconds. kind of a piss off really .. Any ideas? Im thinking it needs 1.6 or higher to get 4 ghz on this =[

[peterpiper]

Thats alot of volts mate I have that exact stepping & can bench at 4200Mhz with that voltage!!!!

Try tweaking your ram settings & giving your vMCH some more volts

By the way i'm using a Turiq Tower with a 60CFM sunon fan inside! Still building my watercooling loop

I've played around a lot, temps hit 54 degrees while running orthos blend, and just short of that running orhos cpu only (speedfan). Now I'm also runnin Vista 64, and from what I'm reading there's a fair amount of confusion over accurate temps from the various programs. It appears even the VID can change with different versions of coretemp. I get different readings from coretemp, everest and speedfan? that aside I agree there may be a limit with the memory, but I think it's either the fact that it's 4 gigs as opposed to 2. More heat and stress on memory controller, or it's the motherboard. 2gigs of the same memory can hit higher speeds according to custompc magazine in a P5K Deluxe!

[famich]

E 6850 L 719A741 4005@1,45VC under load

[peterpiper]

Can 2 processors from the same batch, with the same stepping have different VID's? sorry if it's an ignorant question..

[mashakos]

can you guys mention what cooling you're using cause the 4Ghz overclocks don't sound like they're being done on air. kthx

[tomati]

Can 2 processors from the same batch, with the same stepping have different VID's? sorry if it's an ignorant question..

yes

I get a Q6600 with same stepping as a friends his one git VID of 1.25v as mine is 1.2625v, so I guess it would be the same for E6850.

[peterpiper]

Thats alot of volts mate I have that exact stepping & can bench at 4200Mhz with that voltage!!!!

Try tweaking your ram settings & giving your vMCH some more volts

By the way i'm using a Turiq Tower with a 60CFM sunon fan inside! Still building my watercooling loop

Do you know what the VID of yours is? also what are your voltages? mine are
Vcore 1.5750
Vmem 2.35
Vfsb 1.400
Vnb 1.55
Vsb 1.50
Vich 1.215

any suggestions, anyone?

[dogsx2]

DFI P965-s only can run 1:1 on memory so the time is not so great.
TR 120 Ultra
L722A496

[Leeghoofd]

yeah right you must be kidding me 12.5 secs on 1m with a CPU at 2.7Ghz, so if you use that rig and pull it up to 3.6 you will beat a world record while others need 4-5ghz to obtain a time like that or it's EIST dropping back multi back to 6x...

What is your real CPU speed ?

[michaLcoughliN]

can you guys mention what cooling you're using cause the 4Ghz overclocks don't sound like they're being done on air. kthx

35c idle and 55c load at 1.525vcore with my Zalman 9700

[TheGoat Eater]

can you guys mention what cooling you're using cause the 4Ghz overclocks don't sound like they're being done on air. kthx

swiftech H20-120 compact - 4 now - I plan on buying a waterkeg cooling setup as it suits my needs so that is another 540~USD out of my pocket

[hlonipha]

35c idle and 55c load at 1.525vcore with my Zalman 9700

You might want to check this temps with core temp 95.4 cause those seem a little on the low side specially if you are talking about Orthos small ftts full load.
no way no how you are at 55c with 1.52v.

[dogsx2]

yeah right you must be kidding me 12.5 secs on 1m with a CPU at 2.7Ghz, so if you use that rig and pull it up to 3.6 you will beat a world record while others need 4-5ghz to obtain a time like that or it's EIST dropping back multi back to 6x...

What is your real CPU speed ?

or it's EIST dropping back multi back to 6x... It's 9x456. I don't know why it never shows (6-9) on cpu-z. I guess I should disable it so some guys don't get confused

[Supertim0r]

32M...single channel

[Lu(ky]

DFI P965-s only can run 1:1 on memory so the time is not so great.
TR 120 Ultra
L722A496

I have the same setting but CPU at 4.1GHz and memory at 456x2=912 4-3-3-8 2t 2.0 and get SuperPi 1M at 12.594 something is wrong there on his score?? How can he get better with a lower CPU speed?

[dogsx2]

I have the same setting but CPU at 4.1GHz and memory at 456x2=912 4-3-3-8 2t 2.0 and get SuperPi 1M at 12.594 something is wrong there on his score?? How can he get better with a lower CPU speed?

I got a 24 inch LCD and I can't read what yours says. I think it says we are both at 4100MHz but am not sure. Read the post before yours. LOL

[Supertim0r]

I have the same setting but CPU at 4.1GHz and memory at 456x2=912 4-3-3-8 2t 2.0 and get SuperPi 1M at 12.594 something is wrong there on his score?? How can he get better with a lower CPU speed?

just remove norton and you're 1 sec faster

[dogsx2]

Wish the 4:5 worked. 1.58v load. Really runs cool with TR 120 Ultra.

[aasmaukr]

I'll recieve some sweet stuff pretty soon E6850, Corsair HX620W and two 1gig Crucial 10th anniversary sticks. I'll post results by friday.

[Infa]

Check this out :P

32M Super PI @ 4300MHZ Cas 4-4-4-6



And This is My best Super PI 1M @ 4320Mhz Cas 4-4-3-4



And, Max Validation is 4401.

http://valid.x86-secret.com/show_oc.php?id=234398


Orthos Stable is coming....ETA, Couple of days.

[webwilli]

My SuperPI 32M

Asus P5K Deluxe
2x1024MB G.Skill 8500 GBHK @ 600 5-5-4-8
Water

[Infa]

OMG 1 minute ALL IN THE RAM, i cant even get 4:5 on my Freakin 965 BOARD!
Not even in 450fsb...
now im sad!

[Grinch]

Check this out :P

32M Super PI @ 4300MHZ Cas 4-4-4-6



And This is My best Super PI 1M @ 4320Mhz Cas 4-4-3-4



And, Max Validation is 4401.

http://valid.x86-secret.com/show_oc.php?id=234398


Orthos Stable is coming....ETA, Couple of days.

what's the batch/stepping of your cpu?