Im ditching my water setup and going back to air, looking for something to cool down the 2900. So far the best thing ive found is the HR-03 / R600 but no where to be bought? Is it not out yet? Is there something else?
**NOTE** I dont want to have to mod any cpu coolers or anythin gof that nature, just straight install.
i9-10900k@5.3ghz//MSI MEG z490 Unify//32GB Gskill TridentZ b.die@DDR4666//RTX 2080ti(+150/+700) kingpin bios//Samsung 970 Pro//Corsair AX1200i
Custom Loop: Dual DDCs->Dual EK XE360 w/GT's -> HK IV CPU -> HK IV GPU ->EK X3 Res controlled by Aquaero 6
Then I think you'll have to start looking for HR-03Originally Posted by Circaflex
The R600 HR-03 isnt even out yet
Yep....The R600 HR-03 isnt even out yet
I BLEED TOXIC GREEN
i thought that his's fully coper 2900 hs was one starting to get to be one of the best cooling layouts without liquid
what about shoving a high output fan over the stock one to suppercharge it untill some giant 3pci slot cooler comes out
5930k, R5E, samsung 8GBx4 d-die, vega 56, wd gold 8TB, wd 4TB red, 2TB raid1 wd blue 5400
samsung 840 evo 500GB, HP EX 1TB NVME , CM690II, swiftech h220, corsair 750hxi
The R600 HR-03 isnt even out yet
Its starting to ship this week.
Oh nice, any dates on when it will arrive?
why not just take off the red plastic cover and just strap on a panaflo?
I believe they arrive tomorrow... Some places may get them earlier though.
will the hr-03 realy cool better it looks like its a similar design design and the same amount of material but in an aluminum, or nickel coating
5930k, R5E, samsung 8GBx4 d-die, vega 56, wd gold 8TB, wd 4TB red, 2TB raid1 wd blue 5400
samsung 840 evo 500GB, HP EX 1TB NVME , CM690II, swiftech h220, corsair 750hxi
In this world, anything is better than stock. Dont you forget that
to ati standard cooler.......unless I missed something on HIS's WWW
- E6700@3600 (450x8)@1.425v//3450 (383x9)@1.425v
- P5B dlx
- Zalman 9700Cu
- Corsair Twinx 2Go Pc6400c4 4-4-4-12@2.15v
- Enermax Infiniti 720W
- hd 2900 xt (850cs/1050ms)
- 75Go WD raptor/400Go Seagate;
- Sound Blaster X-FI audio
- XP pro sp2
Keep the stock and run higher fan speeds with ATI tool........at 100% you should be down 10°C from stock
The problem with HR-03 etc is cooling of the Rams.........small heatsinks stuck to them just don't cut it (remember your thermodynamic classes)
Other than that its back to Liquid and danger den..........
- E6700@3600 (450x8)@1.425v//3450 (383x9)@1.425v
- P5B dlx
- Zalman 9700Cu
- Corsair Twinx 2Go Pc6400c4 4-4-4-12@2.15v
- Enermax Infiniti 720W
- hd 2900 xt (850cs/1050ms)
- 75Go WD raptor/400Go Seagate;
- Sound Blaster X-FI audio
- XP pro sp2
If you put good heatsinks on them, its fine. Dont use the crappy sinks that coem with the HR03 and its ok
Keep the stock cooler, hot exaust air leaves the case and thats a good thing.
I'm not sure of the R600 edition, but there's 3 chips on the 8800 GTX that have less than a 1/4 in room before the heatpipes start smacking into them. Too bad those pipes don't go up @ an angle.If you put good heatsinks on them, its fine. Dont use the crappy sinks that coem with the HR03 and its ok
No point in exhausting the air out if it's not cooling the GPU well...
Bend them to fit
Where is the HR-03 R600? I found it on one African retailer of all places lol
In germany the HR-03/R600 is in stock
http://www.pc-cooling.de/VGA-Chipset...ml?language=de
They delayed it a week.. Should show this week for sure.
Do what I did, and make a 120mm duct ducted to the PCI slots.
I BLEED TOXIC GREEN
Where?!!? Lol that will help me
920 c0
6gig Mushkin 1600 6-7-6-18 (Many thanks to TheGoatEater)
285gtx
Dfi x58 t3eh6
http://www.sybaritic.co.za/store/pro...ducts_id=13443Where?!!? Lol that will help me
Enjoy
Posting Permissions
Reply With Quote
Bookmarks