POST YOUR E6850 with OC PERFORMANCE

[NKD]

yea where did u order it from, almost everyone have them, unless u live outside the U.S

[hlonipha]

can u test with prime 25.3, i bet it will stress ur cpu more. it runs small fft's up to 64k, stresses ur L2 cache more, where orthos just does 8k

Actually my first few test runs were using ORTHOS blend and Prime 25.3 and I stopped them both at the 9 hr mark when I got back from work a few days ago. then someone asked me to do an ORTHOS small fft's and I did this run last night. Mine is rock solid stable no matter what stress proggy I run (SO FAR). I will start to increase my FSB to try and tweak for 4.0 GHZ on air over the weekend as my Delta to T is around 15c (that is assuming that intel specs are, 100 tjuntion instead of the reporting 85 on coretemp) I have about 11 more degrees that I might be able to play with before throttling begins. hopefully luck is on my side

[NKD]

well so far running for about 10mins at 4g, will update periodically, i havnt touched the vcore, i have seen on my board, as i up the FSB, more VTT voltage becomes available, 3950 i upped it to 1.41, and at 4G i turned the vtt up to 1.45, and i didnt touch the vcore at all, vtt voltage seems to help alot. vtt voltage on ip-35 pro seems to doing miracle so far. yea ur right no matter what stress program u use, if its stable on etiher one ur computer wont crash. because i dont think anything out there will nearly stress ur computer like either of these.

before i had the vcore at 1.67 and tried to run 4ghz and it would restart within two minutes.

[hlonipha]

well 1mb pi screenshot. as somone asked.

I'm running 12sec on 1M Spi. You might want to try and tweak your ram a bit more to lower your Spi score time.

I'm running CMD RATE 1T on my ram. You might want to try that.

Good luck
Hlo..

[NKD]

I'm running 12sec on 1M Spi. You might want to try and tweak your ram a bit more to lower your Spi score time.

I'm running CMD RATE 1T on my ram. You might want to try that.

Good luck
Hlo..

well i am waiting for the corsair dominators, my ram has issues with tighter timings and sometimes i start getting c1 errors, but as long as leave the timings loose it works fine, though this ram worked great with my evga 680i( filled with problems) board. i could run this ram at 4-4-4-12 up to 960 on my evga board, i am getting the dominators cuz they are listed as fully compatible with the boards. my board wont let me run at 1t there is no option available, however the new beta lets u choose what speed u want to run it at, but this bios is perfectly stable for me, and when they release the final version i will update. but my ram is rated only at 2t i havent tried 1t yet but i dont think that will work.

i will try tightning the ram timings after i find the max stable overlock at this vcore. so far 4.0ghz is looking good.

30min stable at 4GHz and counting.

[neonflx]

i cna't get my memory to run at 1200 i know it can do it cause i used to run i ta t that on my P5N32-E with 2.150 v and never had issues anything over 1000 i can get it stable any suggestions

[NKD]

i tried tighter timings and my computer restarted after 45minutes, and i loosen the timings a bit and its been priming now for about 2 hours. i am running my pc2-6400 in 1:1 ratio, thats why i have to loosen the timings, i am waitings for the dominators which is listed as fully compatible with my mobo, and so i can run it 1:2 and release some pressure on the northbridge and tighten up those timings.

[NKD]

my final speed that i will be running 24/7 is 3950, my memory seems to have issues anything higher than that, once i got it stable at 4ghz for about 4 hours prime stable, once 2 hours but i get random reboots, i think the max my memory can do is what is does at 3950, cant wait till i get my dominators so i can shoot for max fsb

[nugzo]

my final speed that i will be running 24/7 is 3950, my memory seems to have issues anything higher than that, once i got it stable at 4ghz for about 4 hours prime stable, once 2 hours but i get random reboots, i think the max my memory can do is what is does at 3950, cant wait till i get my dominators so i can shoot for max fsb

Thats a great 24/7. I am on water too and i'm 90% sure my 24/7 will be 4000 1.575 bios 1.56 windows 1.53 loaded. 50-55c loaded.

[nugzo]

My next toy .. Just got the good news a few minutes ago. I want a L723A for this too...

[michaLcoughliN]

You jsut gave everyone ur serial for windows..h0w do you feel?

[NKD]

its alright didnt pay for it. LOL.

[Gamer]

Where did you order it from!

hardwareversand.de

[mucker]

E6850 will be my next cpu........

[webwilli]

4 GHz Primestable

1.464 Volt

[hausner]

4 GHz Primestable

1.464 Volt

stepping/batch code?

[dinos22]

you really should look at the screenshot again i think

[nugzo]

4 GHz Primestable

1.464 Volt

You definitely have a good chip. I wouldn't consider 2hours prime stable though. I was 2 hours at same voltage but consistently failed after 4hours or so. I'm now 8+ hours at 1.575 bios, 1.56 windows 1.54 loaded. L723A.

[0DIGy]

you should also try Small FFTs test

but still it's definitely a good chip

my L719B174 runs at 3900@1.4V but i have my FSB wall around 500FSB (it's an E6750) so i can't get 4G stable :'(

[Peepaw]

Here's the results of my first morning with mine.
And before you ask, NO it's not Orthos stable.

[NKD]

finally got my dominators, trying 2000FSB right now. running prim for 10 mins and on. will update if its stable or not.

[NKD]

half an hour so far at 500fsb

[NKD]

1 and half hour at 500fsb

[scwam]

Does this have any significance? Not knowlegable about benching, but I know Lost planet is amazing on this system.

[NKD]

i am able to get my ram stable at 1000mhz with 4-4-4-9, it was tested with memtest at those settings. this was done at cpu speed 3979 with the above memory timings and with 497fsb=1988.