Water Cooled Case Gallery

**Doc PL** · 06-12-2007, 06:38 AM

Answer to no. of loops.
There is only one loop and it goes like this :
Bottom Laing -> Radiator -> NB -> Mosfet 1 -> Mosfet 2 -> RAM - > HDD -> Flow meter - Top Radiator -> Top Laing -> CPU -> GPU -> SB -> Bottom Laing
Mhmmm I tend to mix NB and SB - correct me if I am wrong.

**burton** · 06-12-2007, 07:27 AM

Here is my build

edit i just saw the pic sorry for it being blurry battery was dying

**ANP !!!** · 06-12-2007, 08:09 AM

Nice build Burton

Can u post more pics ??

**victor89** · 06-12-2007, 10:26 AM

Hi!
I want to present you my super-hiper-extra liquid cooling. All cooling system costs me ~200zl (1$=3,5zl). So I payed for ALL this cooling components only 57$

Pump designed for aquariums, on cpu frost2slim by realitynet.pl, gpu homemade prison v2 by our polish constructor Kyniek, reserviour homemade by... i don`t know who

And tubing - cellfast 10 milimeters /13 milimeters - costs 1,2zł for one meter

Oh, and radiator - good old opel rekord with schroud and two thermaltake fans on 12v

So, that was short introduction to this build. Now you can watch photos of my LC - one picture can say more than hundret of words

Enjoy!
[click on photo to entlarge and then, one more time if you wanna larger pics ;P)

(mmm, my cappuccino cup

)

And temps?
Cpu Pentium D 805 @ v-boost mod 1,55v @ 3,7Ghz full stress 62*C @ zalman stg1
GPU Ati x800GT 600/800(DDR) in full load - 37*C

I hope you like it... maby

**burton** · 06-12-2007, 10:33 AM

Originally Posted by ANP !!!

Nice build Burton

Can u post more pics ??

ill take some more later

**afireinside** · 06-12-2007, 02:11 PM

Working on my 900... Moving the water internal soon.

**UncleDavid218** · 06-12-2007, 08:49 PM

**Ad1tya** · 06-12-2007, 08:53 PM

^^ Very neat and nice!

Great Cable management too!

**carholmes** · 06-12-2007, 09:07 PM

Clean setup uncle david. I remember your worklog at dfi-street, didn't you have a Lian Li v2000? btw do you still post over at diy-street, it seems pretty dead over there.

**Okda** · 06-13-2007, 01:53 AM

what about load/idle temps using a single 120.1 rad ?

**UncleDavid218** · 06-13-2007, 05:58 PM

Originally Posted by SaFrOuT

what about load/idle temps using a single 120.1 rad ?

I'm assuming you're talking to me? Well, I'll tell you even if you're not

Ambient room emperatures are about 27 degrees celsius.
The CPU idles (at 1.4v) at around 30 degrees celsius.
Load temperatures typically do not exceed 45c.

**afireinside** · 06-13-2007, 06:13 PM

Is that a coretemp reading during orthos? What voltage? Your loop is very clean

**whoodiestyle** · 06-13-2007, 06:21 PM

Originally Posted by afireinside

Working on my 900... Moving the water internal soon.

wow that is bright

**njkid32** · 06-13-2007, 06:42 PM

I guess I can finally post in this thread since I just recently went to water

I am doing a review on this waterkegIII which has some amazing performance.

Once I drill the holes this will be the final resting place for the unit.

**coolrmaster** · 06-13-2007, 06:51 PM

older exterior pic

current crapola interior pic (sorry but battery died that's it for now)

**UncleDavid218** · 06-13-2007, 09:57 PM

Originally Posted by afireinside

Is that a coretemp reading during orthos? What voltage? Your loop is very clean

Thanks

That's a software reading (ITE Smart Gaurdian which has proved largely accurate) after a few hours of Orthos.

**Bail_w** · 06-13-2007, 10:25 PM

Originally Posted by UncleDavid218

Thanks

That's a software reading (ITE Smart Gaurdian which has proved largely accurate) after a few hours of Orthos.

ITE smart guardian usually 10-15 degree off durning idle temp, and load temp are usually around the same compare to coretemp.

**newls1** · 06-14-2007, 04:25 AM

Originally Posted by njkid32

I guess I can finally post in this thread since I just recently went to water

I am doing a review on this waterkegIII which has some amazing performance.

Once I drill the holes this will be the final resting place for the unit.

Hmmmm...Looks familiar

**funkflix** · 06-15-2007, 03:08 AM

My AMD system.

**fbmbirds** · 06-15-2007, 03:23 AM

[QUOTE=funkflix;2253906]My AMD system.

hey what about that one power plug in do u need to have a 4pin power plug to go in there for the mobo to work? just wondering i have a Asus a8n32-sli deluxe and i have a 4 pin like that and i have it powerd just wondering thats all

**Grinch** · 06-15-2007, 03:45 AM

[QUOTE=fbmbirds;2253916]

Originally Posted by funkflix

My AMD system.

hey what about that one power plug in do u need to have a 4pin power plug to go in there for the mobo to work? just wondering i have a Asus a8n32-sli deluxe and i have a 4 pin like that and i have it powerd just wondering thats all

I think it's for SLI..

**fbmbirds** · 06-15-2007, 03:51 AM

o ok thank i have dual 8800 so im good

**Steffen** · 06-15-2007, 04:23 AM

Older picture of my machine

GPU Cooler

The card

System will be upgraded soon. Triple Thermochill etc.

**Grinch** · 06-15-2007, 04:46 AM

Originally Posted by Steffen

Older picture of my machine

GPU Cooler

The card

System will be upgraded soon. Triple Thermochill etc.

Welcome to xtremesystems..

VERY nice looking setup!

**Sparky** · 06-15-2007, 09:09 AM

Originally Posted by Burn

Where did you/are you getting the UV LED arrays from? I am looking for some and don't like the UV CFFL's because they put out too much "light" and not enough UV.

Which UV cathodes are you using? I have logisys ones and they make my UV glow well but there isn't much excess non-UV light coming from them at all.

Thread: Water Cooled Case Gallery

Thread Tools

Search Thread

Display

Bookmarks

Bookmarks

Posting Permissions