another 03...
01
no LOD used in either run, 165 drivers and gpu's @ 625/1000
a 1m -1 core switched off...
another 03...
01
no LOD used in either run, 165 drivers and gpu's @ 625/1000
a 1m -1 core switched off...
Last edited by Raja@ASUS; 05-05-2007 at 12:55 AM.
the NB chipset is the key to doing 500fsb, most will run 480 or so with a few doing 500 and higher. My board will do 480 no problem...500 no way but with the strap change at 500 that goes a lot looser why would i want too?.
raja hinted at 450fsb...sync mode, trust me thats where you want to run the board
you guys are all fixated with 500+fsb, you really should be looking at where the boards make the best speed and buy the cpu to suit.
Last edited by Tony; 05-05-2007 at 01:41 AM.
Got a problem with your OCZ product....?
Have a look over here
Tony AKA BigToe
Tuning PC's for speed...Run whats fast, not what you think is fast
fully agree man, the latency that you can hit easily at 1900-1920 just simply rocks in sync mode. I am finding myself getting into the top 30 on the bot with stock gpu clocks...
regards
Raja
http://www.thetechrepository.com/showthread.php?t=163
Tony's guide....
btw sync clocking is sweeter on the reaper pc9200 than my cellshock cas 4
Last edited by Raja@ASUS; 05-05-2007 at 02:29 AM.
Also it is not sync clocking. I learned along time ago that OCZ is doing something with their SPD to run 1T different.Originally Posted by raju
http://www.thetechrepository.com/showthread.php?t=163
Tony's guide....
btw sync clocking is sweeter on the reaper pc9200 than my cellshock cas 4
Flash SPD from an OCZ stick on your cellshock and it will increase.
Most of my sets were dieing around 960-970 sync, then I flashed OCZ SPD and got another 100-130 mhz.
http://img213.imageshack.us/img213/3...1trockscm2.jpg
Trick is 7:9 strap is very fast and very stable. That is the only bandwidth shot I can find. Sandra bandwidth of 9000 is pretty good, I believe I got up to 9,300 when I was really tweaking it though.
Last edited by Yoxxy; 05-05-2007 at 05:09 AM.
this is boot from bios, about to bench so more later...
QX6700
this board is all about gtl ref tuning for quads...
If that is Mr. Wu's result on fixing the quadcore issues on the 680i boards, I'm sold. I am tired of working on this IN9 32Xthis is boot from bios, about to bench so more later...
QX6700
this board is all about gtl ref tuning for quads...
DFI 680i LT
Intel Q6600 @ 3.2 Quad Prime Stable @1.3675 and climbing. VRM Temps issues now.
Apogee GT, Laing D5, BI Stealth 240, EK 8800GTX WB
EVGA 8800GTX @ 625/1000 Load Temps 49c
2x Raptor 74GB, 4x WD 400GB, 2xSegate 7200.10 500GB
Lian Li V2000 Black
PCP&C Turbo Cool Custom 1KW
So how is it not Sync...did I tell the SPD to only run async????Also it is not sync clocking. I learned along time ago that OCZ is doing something with their SPD to run 1T different.
Flash SPD from an OCZ stick on your cellshock and it will increase.
Most of my sets were dieing around 960-970 sync, then I flashed OCZ SPD and got another 100-130 mhz
http://img213.imageshack.us/img213/3...1trockscm2.jpg
Trick is 7:9 strap is very fast and very stable. That is the only bandwidth shot I can find. Sandra bandwidth of 9000 is pretty good, I believe I got up to 9,300 when I was really tweaking it though.
Trust me its sync...and I tuned the SPD for cas5 at high clocks so how does this make the ram clock better at cas4???
setup and hold times...that what you need to look at
BTW these don't make it run aync by default
Last edited by Tony; 05-05-2007 at 03:17 PM.
Got a problem with your OCZ product....?
Have a look over here
Tony AKA BigToe
Tuning PC's for speed...Run whats fast, not what you think is fast
Posting Permissions
Reply With Quote
Bookmarks