Just received these units from little devil to test for him
As you can see there is one gpu(not a LD) and 3x CPU (all LD)
One is just a standard LD pot no centre pole all aluminium
Second aluminium one has a centre poll
Third copper base no centre pole
below is the copper base unit on a QX6700@4.55ghz
First up some 3D06 CPU tests with the copper pot
QX6700@4550mhz, 1.75v, 2:3 4.4.4.12 /2.55v
test run at -118/-125 on Asus Commando vmod/vdrop
so far only the copper pot has been mounted and in this case -120
tomorrow i will run some 06 with the gpu pot mounted on a 8800gtx
then i wil try each pot with X6800
i ran some single card 3D06 tonight and it went very well
the CPU pot(copper) held very well @4547mhz
i managed to take some lil movies with my camara but it was a bit tricky the camera only takes 15sec clips5. 3Dmark 2006 - 17124 marks - bazx (OC Forums) - [#5 in 3Dmark 2006 with a single graphic card] - (Geforce 8800 GTX @ 841/1207mhz
you can get them here
http://www.net7.info/1/ln2pots/littledevil/movies/
http://service.futuremark.com/compare?3dm06=1606107
setup
Nice work baz... sounds quite loud though... is the cascade running too?
Last edited by Brettbeck; 04-08-2007 at 10:59 AM.
Originally Posted by Brettbeck
no cascade his time
it was real strange benching without the noise from the cascade
Nice! But watch out with the frost!
[SIGPIC][/SIGPIC]
no cascade his time
it was real strange benching without the noise from the cascade
Hehe.
@ Noob-ftw - Don't forget that with LN2 the PCB will be so cold that any water vapour making contact will freeze instantly, so I think the only problem would be if he left switched the rig off and just left the pot mounted.
Last edited by Brettbeck; 04-03-2007 at 01:56 PM.
Can you say that safely? I wouldn't risk it and put some armaflex and tissue papers over there
nice setup and scores m8. looks like your having fun
Have a nice day
QX9650 ES - 1M @7,984 sec - Asus Maximus Formula SE - LN2
E6600 - 1M @9,937 sec - Asus Maximus Formula SE - LN2
E6600 - 1M @10,016 sec - LN2
E6600 @ 4100mhz AIR -1M 12,500sec
E6600 @ 4285mhz AIR validation
OCZ PC8000 @ 684mhz 5-5-5-15 1M
http://www.overklokken.info --> THE dutch overclocking website.
Nice work!
looks good
interested how it all pans out
Nice testing m8
Last edited by Shark-357; 04-04-2007 at 05:51 AM.
i7 980x @ 4500Mhz 1.45V
Rampage III Extreme
6GB A-Data 1866Mhz+
2x XFX 6970
Crucial SSD 128GB M225
X-Fi Titanium Fatal1ty
Corsair HX1000W
GSX-R 750 Rider
hehe and some more tonight i changed cpu to a X6800 to run some 3D Still on copper base -120
ALL Single Card 8800GTX 851/1223
http://service.futuremark.com/compare?3dm05=2878124
1. The first rule of Bench Club is, you do not talk about Bench Club
2. The second rule of Bench Club is, you do not talk about Bench Club
3. If someone says stop, goes limp, taps out, the the benching is over
4. No bummers in the batcave, apart from unkie dave
5. One Bench at a time
6. No air, no water
7. Benching will go on as long as they have to
8. If this is your first night at Bench Club, you have to Bench
260154 - X6800 @ 5063MHz, 8800 GTX 851/1223 (single gtx)
1. The first rule of Bench Club is, you do not talk about Bench Club
2. The second rule of Bench Club is, you do not talk about Bench Club
3. If someone says stop, goes limp, taps out, the the benching is over
4. No bummers in the batcave, apart from unkie dave
5. One Bench at a time
6. No air, no water
7. Benching will go on as long as they have to
8. If this is your first night at Bench Club, you have to Bench
and some 3D01
87778 - intel X6800 @ 5063mhz 8800gtx @ 851/1223 (single gtx)
http://service.futuremark.com/compare?2k1=9178258
1. The first rule of Bench Club is, you do not talk about Bench Club
2. The second rule of Bench Club is, you do not talk about Bench Club
3. If someone says stop, goes limp, taps out, the the benching is over
4. No bummers in the batcave, apart from unkie dave
5. One Bench at a time
6. No air, no water
7. Benching will go on as long as they have to
8. If this is your first night at Bench Club, you have to Bench
Wow some nice results there Baz, way to go mate will watch this with intrest.
i am have way to much fun with this pot i dont want to change it for another
but i must get on and do some testing
1. The first rule of Bench Club is, you do not talk about Bench Club
2. The second rule of Bench Club is, you do not talk about Bench Club
3. If someone says stop, goes limp, taps out, the the benching is over
4. No bummers in the batcave, apart from unkie dave
5. One Bench at a time
6. No air, no water
7. Benching will go on as long as they have to
8. If this is your first night at Bench Club, you have to Bench
All the best of luck mate, fingers crossed for you, looking for some WR with the setup or very near.i am have way to much fun with this pot i dont want to change it for another
but i must get on and do some testing
If Baz says he doesn't want to change a pot and is saying ''im having way too much fun'' then that sells it to me and im sure the grin on his face has nothing to do with a female insight or the net for that matter
Plus anyhting i have seen from LD is pure sex it's a multi 100% both ways
Ah good point. Just seeing frost on electronics scares me though.Hehe
@ Noob-ftw - Don't forget that with LN2 the PCB will be so cold that any water vapour making contact will freeze instantly, so I think the only problem would be if he left switched the rig off and just left the pot mounted.
[SIGPIC][/SIGPIC]
Beautiful container with beautiful results.Congrats baz and keep going.
I don't really think it's the frost that causes problems. It's when the frost is able to warm up just enough for it to start melting, then you'd have problemsJust seeing frost on electronics scares me though.. As long as it's kept cold with the LN2 though it shouldn't melt.
Thanks bazx for really nice review
regards
------------------------------------------------------------------------------------------------------------------------------------------------
My Work: LittleDevil's SS Cases, LittleDevil's SS Worklog, LD CPU-R1 Dice/LNē Pots, LD GFX-R1 Dice/LNē Pots,
LittleDevil LD PC-V10, LittleDevil's K-Type Temp Display, |EMAIL: ldphasechange@gmail.com
LD PC-V8 Watercooling Cases: LINK
LD PC-V8 ATX/HPTX Watercoolig PC case with 10 expansion slots: LINK NEW!
-------------------------------------------------------------------------------------------------------------
www.ldcooling.com
Find US on Facebook
nice work bazx...
Push 8800 gtx little harder im sure on ln2 card good for
atleast 900mhz
maybe you are rightnice work bazx...
Push 8800 gtx little harder im sure on ln2 card good for
atleast 900mhz
i am running the gpu at -70 right now but next time -90
@little devil it has been a pleasure to work with your pots
and will soon try the others
Last edited by bazx; 04-07-2007 at 06:26 AM.
Posting Permissions
Reply With Quote
Bookmarks