AMD "Thuban" Core (Phenom II X6) XS Overclocking Charts

[V-FrIeNd]

* CPU Model: AMD Phenom II X6 1055T
* CPU Stepping: -
* CPU Frequency: 4004 MHz
* CPU vCore: 1.475V
* CPU Multiplier: 14x
* CPU Turbo: Disabled
* CPU NB Speed: 2860 MHz
* HT Ref Speed: 2860 MHz
* RAM Speed: DDR3-1525
* RAM Timings: 9-9-9-28-1T
* RAM Configuration: 4 GB (2 x 2 GB)
* RAM vDIMM: 1.74V
* Motherboard: BIOSTAR TA870+
* Chipset/Socket: AM3, 870 + SB850
* Cooling: Air (TT Frio)
* Temps: 27C Idle / 49C Load
* Operating System: Windows 7
* 32/64-Bit: 64
* Stable/Suicide/Untested: Untested (Test for Linx All mem 18 min.)

[Radioactive]

V-FrIeNd ,nb voltage,ht voltage and cpu/nb voltage ,what has voltage;

[V-FrIeNd]

V-FrIeNd ,nb voltage,ht voltage and cpu/nb voltage ,what has voltage;

Biostar TA870+ Bios Config

CPU Bus 286

CPU Multipier x14.0 [4004 MHz]
NB x10.0 [2000 MHz]
HT Link x10.0 [2.0 GHz] (16 Bit)
CPU VID 1.275V
NB VID 1.125V

CPU Voltage +0.150 (1.450V)
NB-CPU Voltage +0.200 (1.360V)
HT Voltage +0.150 (1.350V)
DDR Voltage +0.200 (1.740V)
NB Voltage +0.200 (1.350V)
SB Voltage +0.060 (1.150V)
Mem VTT +53% (0.900V)

[Radioactive]

very nais! thanks for info.

[HanaJetso]

CPU Model: AMD Phenom II X6 1090T BE
* CPU Stepping: 1018CPMW
* CPU Frequency: 4000 MHz
* CPU vCore: 1.368V
* CPU NB Voltage: AUTO
* CPU Multiplier: 20x
* CPU Turbo: Disabled
* CPU NB Speed: 2600 MHz
* HT Ref Speed: 2000 MHz
* RAM Speed: DDR3-1800
* RAM Timings: 6-7-6-18-1T
* RAM Configuration: 4 GB (2 x 2 GB)
* RAM vDIMM: 1.72V
* Motherboard: C4F
* Chipset/Socket: AM3, 890FX + SB850
* Cooling: Air (TRUE BLACK)
* Temps: 32C Idle / 58C Load
* Operating System: Windows XP SP3
* 32/64-Bit: 32
* Stable/Suicide/Untested: unStable ?

[Barr3l Rid3r]

(better add CPU/NB vcore in the table, cause it's a very important info)

Ok ok here it goes after 11hrs of test, and lots of time tweaking the CnQ stages, all of them are linx stable.



CPU Model: AMD Phenom II X6 1090T BE
* CPU Stepping: 1015BPAW
* CPU Frequency: 4075 MHz @ PhenomMsrTweaker
* CPU vCore: IDLE 0.97v/1.15v/1.32v/1.37v/1.45v - FULL
* CPU NB Voltage: 1.35V
* CPU Multiplier: 12/15.5/18.5/19/19.5
* CPU Turbo: Disabled
* CPU NB Speed: 2925 MHz
* HT Ref Speed: 2715 MHz
* RAM Speed: DDR3-1670
* RAM Timings: 6-6-6-21-1T
* RAM Configuration: 4 GB (2 x 2 GB)
* RAM vDIMM: 1.66V
* Motherboard: GA790FXT-UD5P
* Chipset/Socket: AM3, 790FX + SB750
* Cooling: Air (TRUE BLACK)
* Temps: 11C Idle / 45C Load
* Operating System: Windows 7
* 32/64-Bit: 64
* Stable/Suicide/Untested: Stable



P.S. Some guys still not understanding about the 8hrs rule for STABLE

[Oldguy932]

Figured out the problem my board was having. If the socket temp hit 76C then it would drop the multi down to 8x because it wasn't checking the core temp. I'm working around it so I should have a stable 8 hours soon as it is running right now.

[eXa]

EDIT:Changed to correct picture and corrected settings to reflect the REAL stable ones...

Ignore volt, multi and frequency in AOD, they are incorrect. I just use AOD as an easy visual for load on cores and for the temp reading.

It idles at 16.5 so adding 13ish C it idles at 29.5 and load is then 51.5. Ambient is 22ish.

Turbo, CnQ C1e is all enabled

CPU Model: AMD Phenom II X6 1055T
CPU Stepping: CCBBE CB 1021DPAW
CPU Frequency: 3500 MHz
CPU vCore: 1.2V
CPU-NB: 1.175v
CPU Multiplier: 14x
CPU Turbo: Enabled, 16x 4000mhz
CPU NB Speed: 2500 MHz
HT LINK: 2500Mhz
HT Ref Speed: 250 MHz
RAM Speed: DDR3-1333 (Corsair XMS3 v3.2)
RAM Timings: 8-8-8-20-27 2T
RAM Configuration: 8 GB (4 x 2 GB)
RAM vDIMM: 1.65V
Motherboard: Gigabyte GA890GPA-UD3H (v2.0)
Chipset/Socket: AM3, 890GX + SB850
Cooling: Air (TRUE BLACK+Nexus D12SL-12 1000rpm)
Temps: 16.5C Idle / 38.5C Load
Operating System: Windows 7
32/64-Bit: 64
Stable/Suicide/Untested:Stable 10hour Prime blend

[FlanK3r]

hanajetso: nice RAM setings, it was stable?! 2000 cl7?

[Oldguy932]

CPU Model: AMD Phenom II X6 1090T BE
* CPU Stepping: 1022BPMW
* CPU Frequency: 4050 MHz
* CPU vCore: 1.45V idle, 1.488V load
* CPU NB Voltage: 1.25v
* CPU Multiplier: 15x
* CPU Turbo: Disabled
* CPU NB Speed: 2700 MHz
* HT Ref Speed: 270 MHz
* RAM Speed: DDR3-1485
* RAM Timings: 9-9-9-24-1T
* RAM Configuration: 4 GB (2 x 2 GB)
* RAM vDIMM: 1.5V
* Motherboard: Crosshair IV bios 905
* Cooling: 'Water' - Modded Corsair H50
* Temps: Idle 26-28C(basically ambient room temp), Load 54C Core, 75C Socket
* Operating System: Windows Vista
* 32/64-Bit: 32
* Stable/Suicide/Untested: 8 hour blend stable

Just wanted to get in my stable setting before tweaking for slightly more speed or whatever I can manage out of the system. I'll probably need to upgrade the cooling to get much farther just because of the throttling I've run into. I think that's because when I had the vapo on before it died I needed to put paste in the socket and that may be adding some heat.

[Barr3l Rid3r]

* RAM Speed: DDR3-1485
* RAM Timings: 9-9-9-24-1T
* RAM Configuration: 4 GB (2 x 2 GB)
* RAM vDIMM: 1.5V
* Motherboard: Crosshair IV bios 905
* Cooling: 'Water' - Modded Corsair H50
* Temps: Idle 26-28C(basically ambient room temp), Load 54C Core, 75C Socket
* Operating System: Windows Vista
* 32/64-Bit: 32
* Stable/Suicide/Untested: 8 hour blend stable

Just wanted to get in my stable setting before tweaking for slightly more speed or whatever I can manage out of the system. I'll probably need to upgrade the cooling to get much farther just because of the throttling I've run into. I think that's because when I had the vapo on before it died I needed to put paste in the socket and that may be adding some heat.

Your Ram is definately a no go on AMD

[HanaJetso]

hanajetso: nice RAM setings, it was stable?! 2000 cl7?

NEVER TRY HARD TEST, JUST RUN ON 1800 6 7 6 1.72v

[Barr3l Rid3r]

this shoul be sticky

[r.p]

same cpu as in post #70, but new MB and cooler


* CPU Model: AMD Phenom II X6 1055T
* CPU Stepping: CCBBE CB 1014GPMW
* CPU Frequency: 4050 MHz
* CPU vCore: 1.536v
* CPU NB Voltage: 1.5v
* CPU Multiplier: 13.5x
* CPU Turbo: Disabled
* CPU NB Speed: 3000 MHz
* HT Ref Speed: 300 MHz
* RAM Speed: DDR3-1600
* RAM Timings: 8-8-8-22-1T
* RAM Configuration: 2 x 2GB
* RAM vDIMM: 1.65V
* Motherboard: ASUS M4A89GTD PRO/USB3
* Chipset/Socket: 890GX + SB850, AM3
* Cooling: Air (Noctua NH-D14)
* Temps: 20C Idle / 48C Load
* Operating System: Windows 7
* 32/64-Bit: 64
* Stable/Suicide/Untested: Stable (9h occt)

ht ref speed still jumping from 300 to 302.4 (bios ver. 1602)

[sam3]

CPU Model: AMD Phenom II X6 1090T BE
CPU Stepping: CCBBE CB 1011BPMW
CPU Frequency: 4038.7 MHz
CPU vCore: 1.476V
CPU Multiplier: 17.5x
CPU Turbo: Disabled
CPU NB Speed: 2077.1 MHz
HT Ref Speed: 230.8 MHz
RAM Speed: DDR3-1846.4
RAM Timings: 7-8-7-24-1T
RAM Configuration: 4 GB (2 x 2 GB)
RAM vDIMM: 1.74V
Motherboard: ASUS Crosshair IV Formula
Chipset/Socket: AM3, 890FX + SB850
Cooling: Water (Corsair Hydro H50)
Temps: 35C Idle / 64C Load
Operating System: Windows 7
32/64-Bit: 64
Stable/Suicide/Untested: Stable

Tested 8 Hours of prime95,

[biohead]

same cpu as in post #70, but new MB and cooler


* CPU Model: AMD Phenom II X6 1055T
* CPU Stepping: CCBBE CB 1014GPMW
* CPU Frequency: 4050 MHz
* CPU vCore: 1.536v
* CPU NB Voltage: 1.5v
* CPU Multiplier: 13.5x
* CPU Turbo: Disabled
* CPU NB Speed: 3000 MHz
* HT Ref Speed: 300 MHz
* RAM Speed: DDR3-1600
* RAM Timings: 8-8-8-22-1T
* RAM Configuration: 2 x 2GB
* RAM vDIMM: 1.65V
* Motherboard: ASUS M4A89GTD PRO/USB3
* Chipset/Socket: 890GX + SB850, AM3
* Cooling: Air (Noctua NH-D14)
* Temps: 20C Idle / 48C Load
* Operating System: Windows 7
* 32/64-Bit: 64
* Stable/Suicide/Untested: Stable (9h occt)

ht ref speed still jumping from 300 to 302.4 (bios ver. 1602)

nice. could you try linpack as well for like 30 minutes?

[r.p]

nice. could you try linpack as well for like 30 minutes?

thx ... i always do my first/quick tests with linepack - had it running for ~1h (no screenshot atm).

[stangracin3]

running mine at 3780 with the NB@ 3150. now only if i could clock the cores up more. I like this chip.



its currently LinX 20 passes of LinX with the problem size of 15500.

[Particle]

Charts updated and posted.

[stangracin3]

its stable but i cant run occt for more than 4 and a half minutes. i can run 100 passes of LinX and play games ALL night but it cant do OCCT

[Sanousie]

Update from my previous 4410mhz oc
* CPU Model: AMD Phenom II X6 1055T
* CPU Stepping:
* CPU Frequency: 4592 MHz
* CPU vCore: 1.675V in bios
* CPU Multiplier: 14x
* CPU NB Speed: 3280 MHz
* HT Link Speed: 328 MHz
* RAM Speed: DDR3-1750
* RAM Timings: 7-7-7-24-1T
* RAM Configuration: 2 x 2GB
* RAM vDIMM: 1.71V
* Motherboard: Gigabyte 890 GPA-UDH3
* Chipset/Socket: 890 AM3
* Cooling: 3/4 Hp single stage cascade
* Temps: -40C Idle / -15C Load
* Operating System: Windows 7
* 32/64-Bit: 32
* Stable/Suicide/Untested: Stable


Click to view full size!

[CrimInalA]

so many people mentioning core temps , which is irrelevant .
show cpu temp .

[nex_73]

^^agree (Maybe most used to intel???)
If you dont get a proper monitoringprogram with your mainboard, try using HWinfo32.

[kirbster1966]

CPU Model: AMD Phenom II X6 1055T
CPU Stepping: CCBBE CB 1020FPMW
CPU Frequency: 4158 MHz
CPU vCore: 1.392V
CPU Multiplier: 14x
CPU Turbo: Disabled
CPU NB Speed: 2375 MHz
HT Ref Speed: 297 MHz
RAM Speed: DDR3-1536
RAM Timings: 8-8-8-26-2T
RAM Configuration: 4 GB (2 x 2 GB)
RAM vDIMM: 1.59V
Motherboard: Gigabyte GA-890FXA-UD5
Chipset/Socket: AM3, 890FX + SB850
Cooling: Air Zalman CNPS 10X Performa
Temps: 23C Idle / 48C Load (using Core Temp)
Operating System: Windows 7
32/64-Bit: 64
Stable/Suicide/Untested: Stable, 500 passes of Intel Burn Test

[eXa]

4.15ghz @ 1.4v Niiiiice!