Antec Twelve Hundred with surprise inside (worklog) ;-P

[piotres]

Progress :



Compressor first time out of box .



Compressor and catpressor together .



NE2134GK vs NL11F





New vision of condensor's look .





I've bought Supco VG-64 during last few weeks .





and also bought some small sleeves for cables ...



That's result of first charge with R507 .





And that's 260W load in 5C ambient temperature , in 20C ambient it's warmer (-30C-32C from first tests)...



Rest of painting - Pipes are gloss black this time .





And small suction line holder ...





Insulation must be thin becasue of side panel ...



:-P



And surprise

More during next few days ...

Regards
Peter

[teyber]

nice work!

you will be frustrated with how often you will need to clean the vg64 if you vacuum like that. i think nol used to vacuum like that and he never cleaned his and it broke

try connecting it via a "t"... only clean it with isopropyl(rubbing) alcohol... and never ever show it a "positive" pressure.

Nice work once again!

[piotres]

nice work!

you will be frustrated with how often you will need to clean the vg64 if you vacuum like that. i think nol used to vacuum like that and he never cleaned his and it broke

try connecting it via a "t"... only clean it with isopropyl(rubbing) alcohol... and never ever show it a "positive" pressure.

Nice work once again!

Thanks for tips about VG64 - Can You post me more tips how to clean it ?

[SAE]

Impressive temps @260W (even -30°C @room temp).
I also like those glossy black tubing.

I need to get my Mach2 GT modded for this kind of loads this next year - one of my good intentions for 2009.

[teyber]

Thanks for tips about VG64 - Can You post me more tips how to clean it ?

hey!

so you have 2 caps yes?

take 1 of them and pour a little bit of rubbing(ispopropyl) alcohol into it.
place cap on (so both ends are capped)

gently shake it (more like rotate it around, back and forth)

open both caps (over a sink lol ) and with low pressure air blow air through it

Also if your vacuum reading is off and you have good oil... or think you should have a lower vacuum then the vg64 is showing, time to clean!

http://www.hvacmechanic.com/forums/c...ages/10169.htm

Cheers!

[ryba]

Short in english: I don't like this project. Shame you Piter.

edited by runmc - Your language is against forum rules. Keep you post in English and keep your language clean.

[teyber]

Co to kurwa ma byc? Poza srednim wykonaniem, projekt jest do dupy i totalnie nie przemyslany. Po co wkladac agregat do obudowy, jak nie jestes w stanie normalnie reszty bebechow tam wsadzic? Totalnie bez sensowne zalozenia.


Short in english: I don't like this project. Shame you Piter.

Im sorry you feel that way

I like it mucho, only thing thats weird IMO is a waste of verticle space but piotres earlier said that he has plans for the top of the case

edit:

Translation programs SUCK lol
"What this whore has byc? Ex srednim production , draw at sight is not until dupy as well total not przemyslany. What for wkladac unit until encapsulations , wherebyprzez co not I'm on cheapened normally balance bebechow yonder stock? Total ex reasonable zalozenia."

[Deathspine]

I find the build very interesting and look forward to seeing it to completion.

[piotres]

And last portion of photos for this unit :



















-49*C is final unloaded .



and -31*C@ 260W load .







I put corosion protect again .





Case like from factory .



Cardboard wasn't enought .







Best Regards
Peter

[fatguy1992]

Very nice

I like that light u put around the flex line .

[sjg0]

Yea that was a really sweet idea with that light tube. The only thing I dont like about this project is that the suction line looks WAY too long. I also dont like how you cut apart all of the 5 1/2in bays except like one on the top and it looks like you could have kept like the top 4-5 bays still in there and still have room. Other than that, FANTASTIC!

[Moc]

But the light idea isn't new. I saw some units with this before.
It looks great

[piotres]

Yea that was a really sweet idea with that light tube. The only thing I dont like about this project is that the suction line looks WAY too long. I also dont like how you cut apart all of the 5 1/2in bays except like one on the top and it looks like you could have kept like the top 4-5 bays still in there and still have room. Other than that, FANTASTIC!

GUYS PLEASE REMEMBER THAT IT IS NOT PC CASE ANYMORE ! It's only case for cooling units . Case with PC (BTW that will be exactly same Antec Twelve Hundred) will be standing next to this case. I've removed all bays (except one ) because on top part of this case will be mounted chiller - by another builder, but I've decided to make his work easier .

[piotres]

Drawing made by owner of this unit :

[Buckeye]

Very Nice Unit Piotres !

You take great care in the packaging of your systems so they do not get damaged in shipment. Very nice to see a builder doing that

That case seems to be a bit bigger than my TJ07 which fits both a SS and Chiller very nicely. My SS suction line is pretty long, it comes out the back of the cooling case, then into the main CPU case through a hole where fans are located in the top rear of the case.

Would it be possible to show the chiller installed also and how it will be setup, insulation and all that good stuff ?

[piotres]

Very Nice Unit Piotres !

You take great care in the packaging of your systems so they do not get damaged in shipment. Very nice to see a builder doing that

That case seems to be a bit bigger than my TJ07 which fits both a SS and Chiller very nicely. My SS suction line is pretty long, it comes out the back of the cooling case, then into the main CPU case through a hole where fans are located in the top rear of the case.

Would it be possible to show the chiller installed also and how it will be setup, insulation and all that good stuff ?

Thanks

I'm sure that "next" builder or owner will show us this case with chiller also here . Sorry I don't know any details about planned chiller .

[sjg0]

GUYS PLEASE REMEMBER THAT IT IS NOT PC CASE ANYMORE ! It's only case for cooling units . Case with PC (BTW that will be exactly same Antec Twelve Hundred) will be standing next to this case. I've removed all bays (except one ) because on top part of this case will be mounted chiller - by another builder, but I've decided to make his work easier .

Ohhh... sorry Piotres. Its pretty much perfect then!

[piotres]

no problem sjg0, I just want to write and show all clear .


http://www.youtube.com/watch?v=Uc-Qi2jsVDE - small movie

[Viss]

Another great piece, i love your work. I hope one day youll be building my cascade

[[XC] Oj101]

I hate you

I want one

[Fr3akyPete]

Very Nice Unit Piotres !

You take great care in the packaging of your systems so they do not get damaged in shipment. Very nice to see a builder doing that

That case seems to be a bit bigger than my TJ07 which fits both a SS and Chiller very nicely. My SS suction line is pretty long, it comes out the back of the cooling case, then into the main CPU case through a hole where fans are located in the top rear of the case.

Would it be possible to show the chiller installed also and how it will be setup, insulation and all that good stuff ?

Is there a thread about your unit somewhere here?
I would love to see that setup.
------------------------------------------------------------
Hey piotres!
Great build!
Hopefully the builder of the chiller inside shows us as much pictures as you did!

[T.Rex]

hi,i will take a lot of pics and first it will be without chiller coz i cant wait to test peters ss and also because i still have some problems to take care of with the chiller,but im sure it will work when i have all parts in my place but your work peter,is perfect

[n00b 0f l337]

I like it, good job Piotres.

[piotres]

Hello n00b - long time . What happend with You if I can ask throught this time in past ?

Thanks

Regards