[PROJECT] Homewrecker V2

[evil-98]

UPDATE!!

ek top is on and ready! wish i had tube to spare i need to
flush the system, but i have any to spare anyways just some
progress, im impressed with eddy, he fix the SB right up!

[SaNxU]

oh! very good job evil

Whe dont drill a little the acrylic to put the leds in it? it will look better i think

Congrats for solving the sb problem

[evil-98]

oh! very good job evil

Whe dont drill a little the acrylic to put the leds in it? it will look better i think

Congrats for solving the sb problem

if in the future i go 3mm i will but for now 5mm is just unsafe
and i value my blocks too much to drill holes in them for now

[disruptfam]

nice evil more updates!

i like the new cam

p.s evil please get the ek acrylic top ....

[nsidious]

outstanding work hopefully we will have some updates soon

[Lagaaja]

That mobo is sexy Definetly subscribed.

[evil-98]

update!

alot of work needs to be done. the radgrill was horrible.. hole
placement was pretty bad, never though this would be an issue
but it turns out it was made more problems then solved. i think
the best thing to do is to commission a machinist to make me
one because i am not happy with the ACRYAN radgrill.. i still
to do some more cutting to the case to fully fit the rad with out
the fans touching the mobo/etc. cutting the case was not much
fun either, alot of hard manual labor, but it did get enough of it
cut where i could atleast install the rad for inspection.

started tubing the mobo, to find the new SB giving me issues
again, with 3/4" OD tubing there is NO, i repeat NO room to install
the second tube, i switched fittings in the end so the SB now uses
a slightly smaller barb so i could at least tiptie it down. its ok now
but i was surprised.

so loop orders go like this:

loop1: 24v D5 - 360GTX - EK Supreme - SB - NB - 150RES Rev1
loop2: DDC 3.2 w/ XSPC top - mosfet - mosfet - DD Ione - DD Ione - 150RES Rev2














Cheers

[manyga]

Very,very,very clean!

Amazing! nice build!

regards

[RockfordFosgate]

Look very nice keep going

[smee]

w00t!! Looking super sexy evil!!!!

MORE UPDATES!!!!!!!!

[septim]

very very nice. whats the meanwell for?

[NoobCake]

i might have not picked this up, but evil, are those compression barbs you using 1/2" ID 3/4" OD, i was assuming they are because you are using DD fat boys with them so they must link to 1/2"..

Thanks

VERY nice and clean build BTW, everything looks like its going perfect, although i would of loved it if you went full compression fitting system

[septim]

compression fitting would not fit on his SB though...

[Sadasius]

Where did you get your black clamps for you EK res's? I broke my acrylic one's and need something a little more reliable.

[mpower1001]

Where did you get your black clamps for you EK res's? I broke my acrylic one's and need something a little more reliable.

http://www.petrastechshop.com/ekmureho.html

[Sadasius]

Thank you! Petra was out of stock so I did end up finding them on the EK site.

[evil-98]

very very nice. whats the meanwell for?

im going to test the D5v at 24v from swiftech efficiency curves
its .75 GPM higher at the same head pressure. now thats not compared
to an aftermarket top, which ill have to look into, but generally its
higher flow and more head pressure and thats both a plus

i might have not picked this up, but evil, are those compression barbs you using 1/2" ID 3/4" OD, i was assuming they are because you are using DD fat boys with them so they must link to 1/2"..

Thanks

VERY nice and clean build BTW, everything looks like its going perfect, although i would of loved it if you went full compression fitting system

those are 1/2" ID 3/4" OD, bitspower. now septim is correct, almost
nothing will fit on the SB, i had to switch from fat boys, to DD hi flow
stubs, which have a much smaller OD and ID, it all works out in the
end so its ok. i would love to have full compression fittings care to
sponsor?

Where did you get your black clamps for you EK res's? I broke my acrylic one's and need something a little more reliable.

i got mine from PPCS, which i am slowly moving away from, i sent an
RMA request months ago with ZERO reply, i had called with little luck
and request for a exchange with the same response..

@everyone else:

thanks for the replies, as an update ive started to design a new rad
grill for the case, i finished the bases but turns out swiftech's site
gives horribly wrong dimensions... very wrong dimensions. i need to
triple check again when i get home but after measuring the rad and
fan i need to redesign the grill. but when its done, i should be able to
drop in the MCR320 with 25mm fans with little to no issue

cheers

[Breathless]

Sorry for an off topic question, but would those Mosfet and Chipset Water blocks fit an Asus Rampage Formula X48?

I was looking to do something similar to this (though not quite as nice) with water cooling the whole board, but I can't find any blocks that say they are "Rampage Compatible".

Thanks

[evil-98]

yes they are rampage compatible

[Breathless]

yes they are rampage compatible

Thanks bud. I thought since it was an intel chipset it would be a little different....

Even the Southbridge block would be the same?

Hence, I would have the same clearance problem as you if I decided to water cool the graphics card as well correct?

[evil-98]

no heres what you would need to completely WC a rampage

NB - http://www.petrastechshop.com/eksnowaa.html
SB - http://www.petrastechshop.com/ekaschwaa1.html
MOSFET - http://www.petrastechshop.com/ekasmowaa4.html

heres a compatibility list, this should have all the info you need

http://site.petrastechshop.com/other...patibility.pdf

[Sadasius]

Love the look of your setup. Doing an awesome job!

[Breathless]

no heres what you would need to completely WC a rampage

NB - http://www.petrastechshop.com/eksnowaa.html
SB - http://www.petrastechshop.com/ekaschwaa1.html
MOSFET - http://www.petrastechshop.com/ekasmowaa4.html

heres a compatibility list, this should have all the info you need

http://site.petrastechshop.com/other...patibility.pdf

Exactly what I was going to ask for next. You are the best. Good luck with your project!

[bigslappy]

no heres what you would need to completely WC a rampage

NB - http://www.petrastechshop.com/eksnowaa.html
SB - http://www.petrastechshop.com/ekaschwaa1.html
MOSFET - http://www.petrastechshop.com/ekasmowaa4.html

heres a compatibility list, this should have all the info you need

http://site.petrastechshop.com/other...patibility.pdf

that's the setup i got !

[evil-98]

small update:

got most of the basic design of my rad grill done, turns
out swiftech's dimensions are really wrong, one thing
i did forget to measure is the length and width of the rad
so if thats wrong too, then its back to the drawing board.
literally.. well needed to test the meanwell, so i decided
to do some modding to that as well. simple, effective. now
all that is left is a power switch and a relay. then it should
be ready to go. right now, whats really holding me back is
the top mounted rad. so the sooner i can get this radgrill
made, the better.

radgrill pics in a few