** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

**radaja** · 05-16-2009, 03:11 PM

hey loco i just installed this and i dont get it.the cpu temp works fine but the mch never moves from 42%.took the fan off of my NB and still nothing.
under loard with fan/under load without fan still 42%.am i missing something.why doesnt everest or ET6 pick up this sensor that is inside the NB?
also is there a way to change it to english?please help
heres some screenshots.i have an airconditioner vent hose blowing directly down from above
tha cpu and NB.first shot is without it about five minutes after i start my computer.
the second one is about two or three minutes after i put the vent hose on,and you can see how the cpu
temps drop but not the NB.ive got a 4500RPM fan on the cpu and a 4000RPM fan on th NB.

**fatguy1992** · 05-16-2009, 07:24 PM

Anyone want Q6600 settings? let me know

Heres my stable 4.05GHz settings

I have, 3.0GHz, 3.2GHz, 3.6GHz, 4.0GHz and 4.2GHz settings all stable.

Code:

******Gigabyte EP45 UD3P******

Robust Graphics Booster.........................[ Auto     ] 
CPU Clock Ratio.................................[ 9        ] 
Fine CPU Clock Ratio............................[ 0        ] 
CPU Frequency 4.05GHz...........................[ 450 x 9  ]

******Clock Chip Control******

CPU Host Clock Control..........................[ Enabled  ] 
CPU Host Frequency (Mhz)........................[ 450      ] 
PCI Express Frequency (Mhz).....................[ 100      ] 
C.I.A 2 [Disabled] 

******Advanced Clock Control******

CPU Clock Drive.................................[ 800mv   ] 
PCI Express Clock Drive.........................[ 900mv   ] 
CPU Clock Skew..................................[ 0ps     ] 
MCH Clock Skew..................................[ 0ps     ] 

******DRAM Performance Control******

Performance Enhance [Standard] 
Extreme Memory Profile (XMP)....................[ Auto ] 
(G) MCH Frequency Latch.........................[ 400MHz ]
System Memory Multipler.........................[ 2.00D  ] 
Memory Frequency 1066...........................[ 900MHz ] 
DRAM Timing Selectable..........................[ Manual ] 

CAS Latency Time................................[ 5        ] 
tRCD............................................[ 4        ] 
tRP.............................................[ 4        ] 
tRAS............................................[ 15       ] 

******Advanced Timing Control******

tRRD............................................[ Auto     ] 
tWTR............................................[ Auto     ] 
tWR.............................................[ Auto     ] 
tRFC............................................[ Auto     ] 
tRTP............................................[ Auto     ] 
Command Rate (cmd)..............................[ 2     ] 

******Channel A Timing Settings******     

Static tRead Value        [ 7 ] ................[ 8        ] 
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ] 

tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto     ] 
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto     ] 
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto     ] 

Dimm 1 Clock Skew Control.......................[ Auto     ] 
Dimm 2 Clock Skew Control.......................[ Auto     ] 
DDR Write Training..............................[ Auto     ] 

******Channel A Driving Settings****** 

Drive Strength Profile..........................[ 1066MHz ] 
Data Driving Pull Up Level......................[ Auto     ] 
cmd Driving Pull Up Level.......................[ Auto     ] 
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]

Data Driving Pull Down Level....................[ Auto     ] 
cmd Driving Pull Down Level.....................[ Auto     ] 
ctrl Driving Pull Down Level....................[ Auto     ] 
clk Driving Pull Down Level.....................[ Auto     ]

******Channel B Timing Settings******     

Static tRead Value        [ 7 ] ................[ 8        ] 
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ] 

tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto     ] 
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto     ] 
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto     ] 

Dimm 1 Clock Skew Control.......................[ Auto     ] 
Dimm 2 Clock Skew Control.......................[ Auto     ] 
DDR Write Training..............................[ Auto     ] 

******Channel B Driving Settings****** 

Drive Strength Profile..........................[ 1066MHz  ] 
Data Driving Pull Up Level......................[ Auto     ] 
cmd Driving Pull Up Level.......................[ Auto     ] 
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]

Data Driving Pull Down Level....................[ Auto     ] 
cmd Driving Pull Down Level.....................[ Auto     ] 
ctrl Driving Pull Down Level....................[ Auto     ] 
clk Driving Pull Down Level.....................[ Auto     ]

******Motherboard Voltage Control******

Load-Line Calibration [Enabled] 
CPU Vcore         [ 1.25000 ]...................[ 1.3625  ] 
CPU Termination   [ 1.20    ]...................[ 1.28   ]
CPU PLL           [ 1.50    ]...................[ 1.500  ]
CPU Reference     [ 0.766   ]...................[ I can't remember the number, but its 2 steps up from default   ]

MCH Core          [1.1      ]...................[ 1.3  ]  
MCH Reference     [0.760    ]...................[ I can't remember the number, but its 1 step down from default  ] 
MCH/DRAM Refernce [0.900    ]...................[ 1.000 ] 
ICH I/O           [1.500    ]...................[ 1.500  ] 
ICH Core          [1.100    ]...................[ 1.100  ] 

DRAM Voltage      [1.800    ]...................[ 2.000    ] 
DRAM Termination  [0.900    ]...................[ 1.000   ] 
Channel A Ref     [0.900    ]...................[ 1.000  ] 
Channel B Ref     [0.900    ]...................[ 1.000  ]  

******Advanced BIOS Features******

CPU Multithreading..............................[ Enabled ] 
Limit CPUID Max to 3............................[ Disabled ] 
No-Execute memory Protect.......................[ Disabled ]  
CPU Enhance Halt (CIE)..........................[ Disabled ]  
C2/C2E State Support............................[ Disabled ]  
C4/C4E State Support............................[ Disabled ] 
CPU Thermal Monitor.............................[ Disabled ] 
CPU EIST Function...............................[ Disabled ] 
Virtualization Technology.......................[ Disabled ]

**babalouj** · 05-16-2009, 09:51 PM

Its been a while since I last checked this thread. I am using bios f4 on my ud3r. Is f9 the best current bios to run with?

**radaja** · 05-16-2009, 10:04 PM

im using F6 that came with the board.seems ok

**Loco23** · 05-17-2009, 04:08 AM

Hi radaja!
Min temp for this sensor is 50. Run MCHTemp, choose "Команды", then "Настройка" and set like this (i highlighted in red)

Turn off your fan on NB. Run prime, choose "custom" and set field "Min FFT Size" to 1024. Press ok. And wait

Originally Posted by radaja

is there a way to change it to english

No

I can translate if you have a questions.

**Homeless2** · 05-17-2009, 05:20 AM

Originally Posted by fatguy1992

Anyone want Q6600 settings? let me know

Heres my stable 4.05GHz settings

I have, 3.0GHz, 3.2GHz, 3.6GHz, 4.0GHz and 4.2GHz settings all stable.

Code:

******Gigabyte EP45 UD3P******

Robust Graphics Booster.........................[ Auto     ] 
CPU Clock Ratio.................................[ 9        ] 
Fine CPU Clock Ratio............................[ 0        ] 
CPU Frequency 4.05GHz...........................[ 450 x 9  ]

******Clock Chip Control******

CPU Host Clock Control..........................[ Enabled  ] 
CPU Host Frequency (Mhz)........................[ 450      ] 
PCI Express Frequency (Mhz).....................[ 100      ] 
C.I.A 2 [Disabled] 

******Advanced Clock Control******

CPU Clock Drive.................................[ 800mv   ] 
PCI Express Clock Drive.........................[ 900mv   ] 
CPU Clock Skew..................................[ 0ps     ] 
MCH Clock Skew..................................[ 0ps     ] 

******DRAM Performance Control******

Performance Enhance [Standard] 
Extreme Memory Profile (XMP)....................[ Auto ] 
(G) MCH Frequency Latch.........................[ 400MHz ]
System Memory Multipler.........................[ 2.00D  ] 
Memory Frequency 1066...........................[ 900MHz ] 
DRAM Timing Selectable..........................[ Manual ] 

CAS Latency Time................................[ 5        ] 
tRCD............................................[ 4        ] 
tRP.............................................[ 4        ] 
tRAS............................................[ 15       ] 

******Advanced Timing Control******

tRRD............................................[ Auto     ] 
tWTR............................................[ Auto     ] 
tWR.............................................[ Auto     ] 
tRFC............................................[ Auto     ] 
tRTP............................................[ Auto     ] 
Command Rate (cmd)..............................[ 2     ] 

******Channel A Timing Settings******     

Static tRead Value        [ 7 ] ................[ 8        ] 
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ] 

tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto     ] 
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto     ] 
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto     ] 

Dimm 1 Clock Skew Control.......................[ Auto     ] 
Dimm 2 Clock Skew Control.......................[ Auto     ] 
DDR Write Training..............................[ Auto     ] 

******Channel A Driving Settings****** 

Drive Strength Profile..........................[ 1066MHz ] 
Data Driving Pull Up Level......................[ Auto     ] 
cmd Driving Pull Up Level.......................[ Auto     ] 
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]

Data Driving Pull Down Level....................[ Auto     ] 
cmd Driving Pull Down Level.....................[ Auto     ] 
ctrl Driving Pull Down Level....................[ Auto     ] 
clk Driving Pull Down Level.....................[ Auto     ]

******Channel B Timing Settings******     

Static tRead Value        [ 7 ] ................[ 8        ] 
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ] 

tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto     ] 
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto     ] 
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto     ] 

Dimm 1 Clock Skew Control.......................[ Auto     ] 
Dimm 2 Clock Skew Control.......................[ Auto     ] 
DDR Write Training..............................[ Auto     ] 

******Channel B Driving Settings****** 

Drive Strength Profile..........................[ 1066MHz  ] 
Data Driving Pull Up Level......................[ Auto     ] 
cmd Driving Pull Up Level.......................[ Auto     ] 
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]

Data Driving Pull Down Level....................[ Auto     ] 
cmd Driving Pull Down Level.....................[ Auto     ] 
ctrl Driving Pull Down Level....................[ Auto     ] 
clk Driving Pull Down Level.....................[ Auto     ]

******Motherboard Voltage Control******

Load-Line Calibration [Enabled] 
CPU Vcore         [ 1.25000 ]...................[ 1.3625  ] 
CPU Termination   [ 1.20    ]...................[ 1.28   ]
CPU PLL           [ 1.50    ]...................[ 1.500  ]
CPU Reference     [ 0.766   ]...................[ I can't remember the number, but its 2 steps up from default   ]

MCH Core          [1.1      ]...................[ 1.3  ]  
MCH Reference     [0.760    ]...................[ I can't remember the number, but its 1 step down from default  ] 
MCH/DRAM Refernce [0.900    ]...................[ 1.000 ] 
ICH I/O           [1.500    ]...................[ 1.500  ] 
ICH Core          [1.100    ]...................[ 1.100  ] 

DRAM Voltage      [1.800    ]...................[ 2.000    ] 
DRAM Termination  [0.900    ]...................[ 1.000   ] 
Channel A Ref     [0.900    ]...................[ 1.000  ] 
Channel B Ref     [0.900    ]...................[ 1.000  ]  

******Advanced BIOS Features******

CPU Multithreading..............................[ Enabled ] 
Limit CPUID Max to 3............................[ Disabled ] 
No-Execute memory Protect.......................[ Disabled ]  
CPU Enhance Halt (CIE)..........................[ Disabled ]  
C2/C2E State Support............................[ Disabled ]  
C4/C4E State Support............................[ Disabled ] 
CPU Thermal Monitor.............................[ Disabled ] 
CPU EIST Function...............................[ Disabled ] 
Virtualization Technology.......................[ Disabled ]

3.6 settings would be appreciated with your reference values. Hopefully they'll help my 1.3125 VID chip :[

**radaja** · 05-17-2009, 09:09 AM

Originally Posted by Loco23

Hi radaja!
Min temp for this sensor is 50. Run MCHTemp, choose "Команды", then "Настройка" and set like this (i highlighted in red)

Turn off your fan on NB. Run prime, choose "custom" and set field "Min FFT Size" to 1024. Press ok. And wait

No

I can translate if you have a questions.

thanks loco23.so i click the one marked in red,which then shows the temps as mch -58 and cpu as -71?

**Loco23** · 05-17-2009, 09:39 AM

Originally Posted by radaja

thanks loco23.so i click the one marked in red,which then shows the temps as mch -58 and cpu as -71?

I was wrong

Choose the first item again

You tried to run prime? Temperature is increased?

**radaja** · 05-17-2009, 09:59 AM

Originally Posted by Loco23

I was wrong

Choose the first item again

You tried to run prime? Temperature is increased?

yep i tried but still no luck.ive even tried moving the setting from 50c to -7c.but no luck

**Loco23** · 05-17-2009, 10:23 AM

Leave all settings by default.
What you MCH Core voltage?
P45 very cold chipset. I have never seen more than 50 degrees, once installed HR05 on NB.
Try run prime about an hour, as i wrote above.

**radaja** · 05-17-2009, 10:28 AM

right now my mch core is at 1.30v.ill keep messing around with it.thanks for your help

**Hoss331** · 05-17-2009, 10:33 AM

That programs doesnt want to run for me, keeps giving me an error code 2 on install and I cant read the rest.

**radaja** · 05-17-2009, 10:35 AM

i think i might try reinstalling it.i cant seem to get it to work.i just tried a blow dryer(hot air) on the NB but still no change in temp readout.
ive been primimg for an hour now,this cpu is a monster!
9x458@4124 with stock vcore(1.237v in bios/1.216v load)

simply amazing

**Loco23** · 05-17-2009, 10:42 AM

Originally Posted by radaja

i think i might try reinstalling it.i cant seem to get it to work.i just tried a blow dryer(hot air) on the NB but still no change in temp readout.
ive been primimg for an hour now,this cpu is a monster!
9x456@4104 with stock vcore(1.237v in bios/1.216v load)

simply amazing

Try increase MCH Core voltage to 1.5 just for test and run prime/blend again.

**Loco23** · 05-17-2009, 10:47 AM

Give me your email, i'll send old version of this program.
Or try this version - http://cp.people.overclockers.ru/cgi...HTempSetup.zip

**radaja** · 05-17-2009, 10:48 AM

ok i will do as soon as i stop this priming run

thanks again for your help.
ill get back to you in about 20 minutes.

**Loco23** · 05-17-2009, 11:36 AM

Originally Posted by Hoss331

That programs doesnt want to run for me, keeps giving me an error code 2 on install and I cant read the rest.

Take a screenshot with error, maybe i can help you.

radaja, you use Vista or XP?

**radaja** · 05-17-2009, 11:39 AM

i use vista.i just installed it,but it stays at 50c now.if i move the setting to say 20c,does that mean once it goes above 20c the temp sensor will move?

**Loco23** · 05-17-2009, 11:54 AM

Originally Posted by radaja

if i move the setting to say 20c,does that mean once it goes above 20c the temp sensor will move?

No.
From MCHTemp's FAQ:
The sensor is not able to measure the temperature below a certain value (hereafter Tmin). Tmin depends on the specific chip, and typically lies in the range of 40 to 50 ° C, but in rare cases can reach 66 ° C. Tmin can not be determined programmatically, so MCHTemp considers it equal to 50 ° C.

With Vista maybe some problem, one moment please

**Loco23** · 05-17-2009, 12:01 PM

Because the driver is not digitally signed you need to load the operating system in test mode. Also you may use Driver Signature Enforcement Overrider or ReadyDriverPlus.

**radaja** · 05-17-2009, 12:03 PM

Originally Posted by Loco23

Because the driver is not digitally signed you need to load the operating system in test mode. Also you may use Driver Signature Enforcement Overrider or ReadyDriverPlus.

is this directed to me?cause i dont have problems loading the program.

**Loco23** · 05-17-2009, 12:06 PM

Originally Posted by radaja

is this directed to me?

It's for all Vista users

I use XP, never ran MCHTemp on Vista.

**Hoss331** · 05-17-2009, 12:06 PM

The first beta one you posted would give me the error but the second works fine, I guess the beta doesnt like win7.

**Loco23** · 05-17-2009, 12:12 PM

Hoss331, fine! I'm glad that was able to help you

**Armored_Kech1** · 05-17-2009, 12:13 PM

Sorry guys but I'm told there is no temp sensor inside the actual NB on the UD3P.

Thread: Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Thread Tools

Search Thread

Rate This Thread

Display

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

Thread: ** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Thread Tools

Search Thread

Rate This Thread

Display

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

Thread: Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P