Intel Core Temperature Monitor plugin for MBM5 (WinXP) - download now!

[lawrywild]

hmm that's weird, it's fine here..

[freecableguy]

Hehe, thanks mate, did not read the readme.. Works "perfect" now!

Are there any configs for the other senors on P5B?

Asus P5B MBM5 sensor data files are in this thread:
http://www.xtremesystems.org/forums/...d.php?t=121183

[lawrywild]

Just tested new files, same thing, both Core 1 temp

[freecableguy]

Just tested new files, same thing, both Core 1 temp

and yet funkflix's readings are correct as well as the yonah laptop that I am running testing on....i really am having hard time figuring this out.

[lawrywild]

Still reading both Core 1 on the driver you just sent

[funkflix]

Ok, now the final screens, thanks to u all for the help etc.!







But still sometimes the "Core 1" switch back to 0°C, but it is just for less then a second.

[lawrywild]

Funkflix is that on the MBM Update 2 or the original 5.3.7.0?

[funkflix]

It is with the original 5.3.7.0 and the Update for P5B fcg linked above.

[lawrywild]

I think it must be the Update 2 causing mine to screw up then, coz it was fine last night on the original..

Funkflix can you email me the files you're using? lawrywild *AT* hotmail DOT c*m

[funkflix]

Funkflix can you email me the files you're using? lawrywild *AT* hotmail DOT c*m

Complete MBM5 folder?

@fcg

Here u can see, that both cores sometimes drop down to 0°C, hope u can fix that! If u need any support, just email me, or post here.

[lawrywild]

err nah just the plugin and the driver please

[funkflix]

err nah just the plugin and the driver please

Ok, it is on the way.

[lawrywild]

Thanks, gonna sleep now, I'll try in the morning

[funkflix]

Ok, with the latest *.dll i have no drops to 0°C anymore, just at first MBM start it counts 0°C one time, so the High / Low statistic is a bit falsified, but that is ok for me.

[Millyons]

Ok, with the latest *.dll i have no drops to 0°C anymore, just at first MBM start it counts 0°C one time, so the High / Low statistic is a bit falsified, but that is ok for me.

I might have figured out why it drops to 0c........ im playing with various configs on a clean winxp install on my P5B Dlx......when i set the initial confit to P4P800 i get the 0c drop, but when i set it to P4C800-Deluxe it seems fine

[funkflix]

I might have figured out why it drops to 0c........ im playing with various configs on a clean winxp install on my P5B Dlx......when i se the initial confit to P4P800 i get the 0c drop, but when i set it to P4C800-Deluxe it seems fine

Hmm, i did not set even one of this pre configs this time?!

Anyway, i installed and configured now the plugin for my GX2 and it works perfect, but now i'm back with the 0°C problem.. 96% of the time now, it shows 0°C again for Core 1.. Really strange thing imho!

[funkflix]

Argh! My fault, the Core 1 Plugin switched to "Should display board sensor = None".. But i'm sure i didn't changed anything..

[Millyons]

i played with this for a while and this is what i found:

- for P5B Dlx choosing the P4P800 config results in core temps dropping to 0 once in a while (to me it seemed whenever a core goes from idle to load) choosing P4C800-Deluxe resolves that, im going to post a config file but im typing this so ppl that are not using P5Bdlx are aware, and to know how to fix it on their mobos if possible

- cpu usage monitor in MBM causes both cores to show one temperature in my case it was core #1 temp for both, i dont know if you can fix that FCG, but its really usefull to have both....if it isn't possible to fix im probably gonna run cpu usage "on" with only one core showing, it really usefull when going through loggs to see what was happening and both my load temps are the same so it doesnt make to much difference, at least to me

[dinos22]

mbm's my favourite program i must say.....good to see it's got the plugin

[lawrywild]

You're right, I just switched off cpu usage and restarted MBM and Both coretemps are being reported properly again

edit: oh and fcg, could you please make the default name to Core 1,2,3 etc rather than CORE 1,2,3.... I hate CAPS

[scaramonga]

When is this going to be available guyz?

[Millyons]

You're right, I just switched off cpu usage and restarted MBM and Both coretemps are being reported properly again

edit: oh and fcg, could you please make the default name to Core 1,2,3 etc rather than CORE 1,2,3.... I hate CAPS

LOL man i was just about to ask the same, although i would like Core #0, Core #1 etc the best

[lawrywild]

LOL man i was just about to ask the same, although i would like Core #0, Core #1 etc the best

nah, definately Core 1,2,3 etc

well, actually why not just make it so it doesn't change the name everytime it starts, so we can choose the prefix ourselves that's best for everyone

[webwilli]

Hmm, i did not set even one of this pre configs this time?!

Anyway, i installed and configured now the plugin for my GX2 and it works perfect, but now i'm back with the 0°C problem.. 96% of the time now, it shows 0°C again for Core 1.. Really strange thing imho!

Plugin for GX2? Where can i get it?

edit: found it...

[funkflix]

edit: oh and fcg, could you please make the default name to Core 1,2,3 etc rather than CORE 1,2,3.... I hate CAPS

Second that!