LianLi V2100 Chiller

**Overklokk** · 08-28-2006, 12:33 PM

Hello.

This is my latest projekt .

Before i start

Kondenser and fan.

Danfoss NL9F compressor

Power plug

Fancontroll , tempdisplay and on/off switch

This chiller is going too hold about 0 too +10c on water (thats what my custommer want)

Starting too make the heatexchanger tomorrov

**littleowl** · 08-28-2006, 01:08 PM

looks good keep the pics and updates comeing!!

**Overklokk** · 08-28-2006, 07:55 PM

Originally Posted by littleowl

looks good keep the pics and updates comeing!!

Tnx!

Hope too doo some more work on it today and wil post pictures as soon as i can

**Overklokk** · 08-29-2006, 07:52 AM

Some more work is done

Tomorrow i get an IWAKI MD 15 :dribble:

Still lots of work todoo

**MeltedDuron** · 08-29-2006, 08:41 AM

lookin good so far

turn that res into a popsicle!

**SMa** · 08-30-2006, 12:51 AM

Looks very simular to mine, altough I use the whole casing. (SilverStone TJ05B)
I'll make a thread about it later on

(made by Jort, work in progress)

**RussC** · 08-30-2006, 09:22 PM

Nice,
Fits well in the system.

RussC

**Overklokk** · 09-08-2006, 10:23 AM

More parts has arived and work is going on

PSU+ IWAKI is big

**Overklokk** · 09-08-2006, 10:30 AM

dubble post

**ewsforos** · 09-08-2006, 10:47 AM

Wow! Awesomely thought out. The space you had to work with is pretty much packed

Well done!

**Nefilav** · 09-08-2006, 10:48 AM

What gas are you using for it?

Very neat and tidy , looks so professional and clean. My only concern is the pump, it may need a bit of vibration dampening if its anything like mine...sits on the carpet on neoprene, i can still feel it on my desk a few feet away.

**Overklokk** · 09-08-2006, 11:09 AM

Originally Posted by Nefilav

What gas are you using for it?

Very neat and tidy , looks so professional and clean. My only concern is the pump, it may need a bit of vibration dampening if its anything like mine...sits on the carpet on neoprene, i can still feel it on my desk a few feet away.

Wil use r134a.

The pump is sitting on som vib dampers.... hope that wil be good

**Nefilav** · 09-09-2006, 01:44 AM

Well, if 2 squashed pipes of neoprene stop the vibration from my bigger pump it should work great. I bought it up because thats a quiet compressor, implying the whole setup needs to be quiet.

Will the pump be relayed to the compressor, or computer system?

**Overklokk** · 09-09-2006, 11:29 PM

Okay... thing is going forward and the cooler is soon ready.

Her it is ready too power on for the first time

Water temp when i first start it.

After 5 minits +9c

After 8 minits -0,3c

And finaly after 18minits -17c

-13c on the waterblock

This cooler is buildt for +0 too +10c watertemp loaded..... lets se if it can handle that soon.

Waiting for the parts ...... AMD FX62 + GX2 +++

**Overklokk** · 09-11-2006, 07:59 AM

Originally Posted by SoddemFX

Wonderfull work Overklokk!

Realy nice installation, i think your customer will be very happy

Tom

Tnx!

I am waiting for the hardware too this chiller (fx62 + gx2 etc) So i deside too test it on a E6700 @ 4000 1,65 real MM volt.

First some isulating

This block is AM2 so i made some temporary hold downs for socket 775

KjÃ¸lerThe chiller is ment too hold +0 too +10c on water load so lets se what it did on my conroe.

Witout load -22c

After 2 ouers idle in winxp -11c:

After 2 ouer with 3dmark 01 looping -8,9c

**CedricFP** · 09-11-2006, 08:17 PM

Wow, incredible stuff.

**RussC** · 09-12-2006, 12:22 PM

Sweet,
what size compressor it that?

RussC

**p0tter** · 09-12-2006, 04:47 PM

Looks professional, the front control panel looks good.

**Overklokk** · 10-01-2006, 11:23 PM

Ok.... finaly i godt nthis baby upp and running.

The res/evap was too little to handle the load wel from a FX60 and 2 x 7900GTX

So i godt a SWEP B5-10 HX and put it on... i placed it on the back side of the casce.

I also mounted a CPEV on it so that i can adjust the cooling like i want

Its now running with a fx60 @ 3340mhz and 2 x 7900GTX @ 760/890 nad is idling in win @ -12c water temp. Under load the water is about -2c

**nickfd** · 02-06-2007, 01:41 PM

Just wanted to say you did an incredible job setting up this phase cooling system! Great work!

**n00b 0f l337** · 02-06-2007, 03:17 PM

A plate hx works by crossing the layers of flow with incredibly high surface area, by use of plates.

**epion2985** · 02-06-2007, 08:35 PM

performance isn't good but could be bettered by a better heat exchanger and better refrigerant, 134a is pretty skimpy.

good work

**[XC] mysticmerlin** · 02-07-2007, 12:30 AM

That is a Mach1 hacked up right? Looks just like the Mach1 I have sitting here control and all.
Looks good either way.

**~~Modzilla~~** · 02-07-2007, 06:36 AM

Very nice work.

**LittleDevil** · 02-07-2007, 02:20 PM

Really nice waterchiller

regards

Thread: LianLi V2100 Chiller

Thread Tools

Search Thread

Rate This Thread

Display

LianLi V2100 Chiller

Bookmarks

Bookmarks

Posting Permissions