MMM
Results 1 to 8 of 8

Thread: 8rda+ mem mod?

  1. 12-10-2002, 12:51 PM #1
    Emericana
    Emericana is offline
    Xtreme Member
    Join Date
    Nov 2002
    Location
    Wellesley, MA
    Posts
    392

    8rda+ mem mod?

    anyone know how to do this? i can take pictures of my board if this will help but i dont know what to take a pic of.

    for those of you who dont know the vmem on the board goes up to 2.9 and i would like to use 3.2
    -2600 mobile AQYHA 0346 XPMW Y @ 2600mhz 1.9v (hits brick wall after this)
    -Water Cooled- Dtek Spiral and Dtek NB Block, Ehiem 1250, Dtek Rad... around 43C Full Load
    -DFI Infinity
    -2x256 Twinmos BH5
    -Geforce FX 5900 XT
    Reply With Quote Reply With Quote
  2. 12-12-2002, 12:03 PM #2
    N8
    N8 is offline
    Xtreme Mentor
    Join Date
    Jun 2002
    Location
    PA, USA
    Posts
    2,662
    Are you able to take a high-res pic of the whole board? I don't own this board, but I wouldn't mind finding out how this mod is done
    E8600. EP45-UD3P. 500FSB 24/7. Still WinXP. Heatware
    Reply With Quote Reply With Quote
  3. 12-13-2002, 08:37 PM #3
    Bushboy
    Bushboy is offline
    Xtreme Member
    Join Date
    Sep 2002
    Location
    Boston, MA
    Posts
    406
    Send a message via AIM to Bushboy
    PMed DDTung and got this reply:

    "REfer to the BD7II Vmem mod. This board uses a similar Winbond chip(with 4 extra pins) but the Vmod is still using the STR1sense pin.

    DDTUNG "

    The BD7II Vmem mod is known as a hard one, which kinda sucks. Soon as I get my camera back, I'll take some high-res pics, but I'm not sure I want to risk the board doing a tricky Vmod...I'll read up more on the BD7II and see how hard it is.
    XP2400+
    Abit NF7 2.0 Vmem and VDD modded
    256MB Kingston HyperX PC3500
    Sapphire 9500np (Vref, Vmem, Vddq, Vcore modded)
    Fully Phase Change cooled
    Reply With Quote Reply With Quote
  4. 12-14-2002, 10:56 AM #4
    muzz
    muzz is offline
    Xtreme Addict
    Join Date
    Nov 2002
    Location
    MA.
    Posts
    1,783
    Only problem is Randi tried that mod and was unsuccessful( bye bye rda), he didn't state if the mod was wrong for this board, or if he made a mistake with his work. If I knew that was the exact same mod, then it is tough, but feasible........ but didn't like the fact that we now have 1 burnt up rda+ in our midst.
    Zen2 Has brought AMD back!
    Reply With Quote Reply With Quote
  5. 12-16-2002, 05:40 AM #5
    N8
    N8 is offline
    Xtreme Mentor
    Join Date
    Jun 2002
    Location
    PA, USA
    Posts
    2,662
    boooo!
    E8600. EP45-UD3P. 500FSB 24/7. Still WinXP. Heatware
    Reply With Quote Reply With Quote
  6. 12-16-2002, 06:09 AM #6
    cobase
    cobase is offline
    Registered User
    Join Date
    Aug 2002
    Location
    Austria
    Posts
    34
    How do I have to mod the Chip to get 3,2V?

    http://www.winbond.com/PDF/sheet/W83301DR-O.pdf
    Reply With Quote Reply With Quote
  7. 12-16-2002, 11:04 AM #7
    N8
    N8 is offline
    Xtreme Mentor
    Join Date
    Jun 2002
    Location
    PA, USA
    Posts
    2,662
    cobase,

    MrIcee explained it a bit here:
    http://www.xtremesystems.org/forums/...3483#post73483

    Mind you, he failed w/ this mod...seems as tho the leg was too brittle
    E8600. EP45-UD3P. 500FSB 24/7. Still WinXP. Heatware
    Reply With Quote Reply With Quote
  8. 12-16-2002, 02:48 PM #8
    cobase
    cobase is offline
    Registered User
    Join Date
    Aug 2002
    Location
    Austria
    Posts
    34
    Ouch! Looks rather nasty, this mod.
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules