DFI LANparty DK P45-T2RS/T3RS (Intel P45) - News|Info|Results

[SeLecT]

DFI LANparty DK P45-T2RS/T3RS / Plus(Intel P45)






Content of the thread

• General informations
• Impressions
• Specifications
• The bios
• Downloads
• Important Informations
• Results
• compatible memory & coolers
• Important links

General informations

After the P35 Board of the DK-Family, the P45 Boards is now available and this is the official thread for the board. I have this board at home and i will give you results und screens. This thread isn't final.
So guys, buy this board and test it

Impressions


(Bilder von patrock84 und meiner Wenigkeit)

Specifications

• CPU
  
  • LGA 775 socket for:
    - Intel® Core2 Quad and Intel® Core2 Duo
  • Supports Intel Enhanced Memory 64 Technology (EMT64T)
  • Supports Enhanced Intel SpeedStep Technology (EIST)
  • Supports Intel Hyper-Threading Technology
  • Supports 1333/1066/800MHz FSB
  • Supports Enhanced Intel SpeedStep Technology (EIST)
    
• Intel® chipset
  
  • Intel® chipset
    - Northbridge:
    Intel® P45 Express chipset
    Intel® Fast Memory Access technology
    - Southbridge: Intel® ICH10R
• Memory
  
  • Four 240-pin DDR2 DIMM sockets
  • Supports DDR2 667/800 MHz
  • Delivers up to 12.8Gb/s bandwidth
  • Supports dual channel (128-bit wide) memory interface
  • Supports up to 8GB system memory
  • Supports unbuffered x8 and x16 DIMMs
• Expansion Slots
  
  • 2 PCI Express (Gen 2) x16 slots - 2-way CrossFire: One slot operating at x16 (16-lane port) or two slots each operating at x8 (8-lane ports) bandwidth
  • 2 PCI Express x1 slots
  • 2 PCI slots
• BIOS
  
  • Award BIOS
  • 8Mbit SPI flash BIOS
  • CMOS Reloaded
• Audio
  
  • Realtek ALC885 High Definition audio CODEC
  • 8-channel audio output
  • DAC SNR/ADC SNR of 106dB/101dB
  • Full-rate lossless content protection technology
  • Optical S/PDIF-out and coaxial RCA S/PDIF-out interfaces
• LAN
  
  • Marvell 88E8053 PCIE Gigabit LAN controller
  • Fully compliant to IEEE 802.3 (10BASE-T), 802.3u (100BASE-TX) and 802.3ab (1000BASE-T) standards
• IDE
  
  • JMicron JMB368 PCI Express to PATA host controller
  • Supports up to 2 UltraDMA 33/66/100Mbps IDE devices
• Serial ATA with RAID
  
  • Intel Matrix Storage technology
  • Supports up to 6 SATA devices
  • SATA speed up to 3Gb/s
  • RAID 0, RAID 1, RAID 0+1 and RAID 5
• Rear Panel I/O Ports
  
  • 1 mini-DIN-6 PS/2 mouse port
  • 1 mini-DIN-6 PS/2 keyboard port
  • 1 optical S/PDIF-out port
  • 1 coaxial RCA S/PDIF-out port
  • 6 USB 2.0/1.1 ports
  • 1 RJ45 LAN port
  • Center/subwoofer, rear R/L and side R/L jacks
  • Line-in, line-out (front R/L) and mic-in jacks
• Power Management
  
  • ACPI and OS Directed Power Management
  • ACPI STR (Suspend to RAM) function
  • Wake-On-PS/2 Keyboard/Mouse
  • Wake-On-USB Keyboard/Mouse
  • Wake-On-LAN
  • Wake-On-Ring
  • RTC timer to power-on the system
  • AC power failure recovery
• Hardware Monitor
  
  • Monitors CPU/system/Northbridge temperature and overheat alarm
  • Monitors Vcore/Vdimm/Vnb/VCC5/12V/V5sb/Vbat voltages
  • Monitors the speed of the cooling fans
  • CPU Overheat Protection function monitors CPU temperature and fan during system boot-up - automatic shutdown upon system overheat
• PCB
  
  • 4 layers, ATX form factor
  • 24.5cm (9.64") x 30.5cm (12")

The bios - !press F9 for more settings!

Downloads

• Beta-Bios
• Bios
• Handbuch/Manual
• DFI DK P45 OC Guideline.pdf

• Originally Posted by Fresh_Thing

  complete smartguardian pack incl. 2 backgrounds HWLuxx Edition !!!
  
  SmartGuardian_DK_P45_HWLuxx_Edition

Important nformations

Zum Non-Plus:
The nonplus version is not as good as the plus version vor overclocking. If you want to buy the DFI, then buy the plus version. Most of the overclocking results are reached on the plus version.

F9 for more memorysettings in bios




Zum DFI DK Plus:

p45 normal and p45 plus both have chipset A2 revision and A1 motherboard revision as of NOW. Difference between the normal and the plus is the additional 2 SATA ports and also the double boot after saving bios has been resolved for the P45 plus.

Results

• 680Mhz FSB on DFI LP DK P45 T2RS Plus
• 600Mhz SuperPi 32M on DFI LP DK P45 T2RS Plus

compatible memory & coolers[/hr]

Aircooling:
Noctua U12P
TR Ultra 120 True Black / Extreme
Scythe Mine
Thermalright HR-01 Plus

Water-cooling NB-SB-Mosfets:

EK-Mosfet DFI DK - Acetal
Watercool Kühler
NB/SB by Anfitec - Pictures: Klick
Spawa by Anfitec
(Now at pc-icebox.de zu haben)



Memory:

Memory for overclocking

• Crucial Ballistix Tracer PC8500 1066MHz BL12864AL1065.8FE5
• takeMS Mach2 2GB PC2-8500U CL5-5-5-18 TMS1GB264C082-105EP
• Corsair XMS2 Dominator 2GB PC2-8500U CL5-5-5-15 TWIN2X2048-8500C5D
• OCZ Reaper HPC Edition Kit 2GB PC2-9200U CL5-5-5-18 OCZ2RPR11502GK
• OCZ Reaper HPC Edition 2GB Kit PC2-9600 CL5-5-5-18 OCZ2RPR12002GK
• OCZ Flex II 4GB Kit PC2-9200 CL5-5-5-18 OCZ2FXT11504GK
• TeamGroup Xtreem Dark 4GB Kit PC2-8500U CL5-5-5-15 TXDD4096M1066HC5DC-D
• Chaintech Apogee GT DIMM Kit 4GB PC2-8500U CL5-5-5-15
• Kingston HyperX DIMM Kit 4GB PC2-6400U CL5-5-5-15 (DDR2-800) (KHX6400D2K2/4G)
• Cellshock DIMM Kit 2GB PC2-8500U CL5-5-5-15 (DDR2-1066) (CS2221550)
• G.Skill Kit 4GB PC2-8000U CL5-5-5-15 (DDR2-1000) (F2-8000CL5D-4GBPQ)
• G.Skill Kit 4GB PC2-8800U CL5-5-5-15 (DDR2-1100) (F2-8800CL5D-4GBPI)
• G.Skill Kit 4GB PC2-6400U CL5-5-5-15 (DDR2-800) (F2-6400CL5D-4GBPQ)
• Chaintech Apogee GT Kit 4GB PC2-9200U CL5-5-5-15
• Crucial Ballistix Tracer PC6400 2*1 GB BL12864AL804.16FD3

Important Information

vDroop-Mod

Here the vDroop-Mod. I made it with 20 kOhm VR. I think 10 kOhm should be work too.





Results:

Without Mod, R = 2,22 kOhm: 1,395 V / 1,385 V

With Mod, R = 1,37 kOhm: 1,400 V / 1,395 V (The poti is set at ca. 4 kOhm)

Measurepoints DFI LANparty DK P45-T2RS / Plus

Messgerät : Voltcraft VC-531 Ampere Zange + Multimeter ( NP : 75 € )

Real Volt - Messung at Windows @ IDLE....with a Q9550 E0 @ FSB 500 @ 4255 Mhz

--------------------------------------------------------------------------

CPU PLL ( Bios 1.55v.) ......Real : 1.578v...........Droop : + ~ 0.03v.

NB Core ( Bios 1.420v.) .....Real : 1.420v...........Droop : nichts

VDIMM ( Bios 2.218v. ) .....Real : 2.245v. .........Droop : + ~ 0.03v.

VTT ( Bios 1.280v. ) .......Real : 1.298v. ..........Droop : + ~ 0.02v.
--------------------------------------------------------------------------

Heatpipe Mod :

Important links

• DFI LANparty DK P45-T2RS @ DFI Homepage
  
• DFI LANparty DK P45-T2RS @ geizhals.at
  
• DFI LANparty DK P45-T3RS @ geizhals.at
  
• DFI LANparty DK P45-T2RS Plus @ HPM
  
• More infos of the DFI LANparty DK P45-T2RS Plus
  
• short review of the DFI LANparty DK P45-T2RS Plus
  
• DFI LANparty DK P45-T2RS @ Geizhals.at
  
• Quickreview by Clunk
  
• Bios how-to
  
• How to Make a USB Pen Drive Bootable

[SeLecT]

The boards works, but i have an great problem....

I could'nt reach more than FSB 400Mhz. The maximum was 430Mhz, but it wasn't stable. 500Mhz is impossilbe

Do you have some same experiences?

[Achill3uS]

nice mobo but 4 phase design (or correct me if im blind ) is really poor nowdays im curious to the digit pwm LanParty UT edition, dont you have any info about it? btw nice thread, let's fill it

[Peter Burg]

Let's wait for the people to get the boards. I think you're one of the first, so be patient. And fore sure it's the first release of the BIOS

[patrock84]

Actually i have problems with FSB above 400MHz..
CPU: E8400 or 8200 , same results..

[Peter Burg]

Let's wait for a new BIOS

[SeLecT]

Originally Posted by Achill3uS

nice mobo but 4 phase design (or correct me if im blind ) is really poor nowdays im curious to the digit pwm LanParty UT edition, dont you have any info about it? btw nice thread, let's fill it

For a dualcore it is ok i think

The UT version will have some digital pwm.

Originally Posted by Peter Burg

Let's wait for the people to get the boards. I think you're one of the first, so be patient. And fore sure it's the first release of the BIOS

Yeah, i know. i have send a mail to DFi....
Waiting for some other people!

Originally Posted by patrock84

]http://www.abload.de/img/dfi001v85.jpg

Actually i have problems with FSB above 400MHz..
CPU: E8400 or 8200 , same results..

Hmm, then is this a Biosproblem!

[Peter Burg]

Originally Posted by SeLecT

Yeah, i know. i have send a mail to DFi....
Waiting for some other people!

Du ich bin Yidaki nur es war schon vergeben :fresse:

[nzbleach]

nice, all the connectors are pretty much placed perfectly. No removable bios chip though -p

[Kean]

Originally Posted by SeLecT

The UT version will have some digital pwm.

There will be UT P45 ddr2?

[SeLecT]

Originally Posted by Kean

There will be UT P45 ddr2?

I think so - http://www.hpm-computer.de/product_i...-P45-T2RS.html


--------------------

[Sem]

i hope there is a DDR2 P45 UT

i know that shop lists it but on the DFI schedule posted in the first post there is only a DDR3 P45 UT

[SeLecT]

Hm, you're right! Lets hope for the board!

And i hope for an new bios!

[Kean]

On schedule in first post, there isn't JR version. So, let's hope there will be UT DDR2 ver.
JR look like this:

[graysky]

What kind of NB Vcore and NB temps are required to run @ 400 MHz?

[SeLecT]

I don't know, because the 400Mhz are not stable... I hope a new bios will fix all these problems! If not, i will sell this board...


PS: Bios screens added!

[alex17 GTX]

Why so few Dram options? This must be an alpha beta whatever early bios... Also.. I though this board was scheduled for middle july...

[SeLecT]

Here a biosscreen from the DK P35 - it has a little bit more dram options

http://www.abload.de/image.php?img=s...800x600c2i.jpg

[alex17 GTX]

I know that! (my rig). And that can't be true. I really hope they release a new bios fast.

[SeLecT]

DFI USA answered me and in the USA they don't sell this board or have an sample of it...

So a mail to Taiwan is out...

[NupSiHoVa]

Hi SeLecT,

I just recieved the Mobo, might wanna hook it up tonight. I dearly hope it doesn't have the same issues as yours.....but more unlikely i think it will.

[emoners]

Originally Posted by Kean

On schedule in first post, there isn't JR version. So, let's hope there will be UT DDR2 ver.
JR look like this:

really? i was kinda waiting for the P45 JR for my mATX rig

[mrcape]

DFI-LP-Jr-P45-T3RS

[CarvedInside]

Been waiting for this board. I think this mobo isn't officially lauched yet. Here in Romania you can find it listed , but they don't have it in stock , so it looks like I'll have to wait a bit more. Hope by the time it gets here, dfi engineers will fix the damn bios.

Any comments on the package, build quality, northbridge cooler?

[SeLecT]

The NDA falls on 30th of june... so you are right, that the board isn't offiicial yet.

I will take some photos of the package soon.