UT P35 + E8500, fsb 608

[DDA]

DFI ut p35, bios 17/3, E8500 Q807***, LN2, ballistix pc8500 2.45v, win xp pro as it was for daily use :

[loopy83]

Try some Tweaks next time.... i think a better time is possible.

[Helgart]

for daily use xp is that really nice score

[before]

Nice clocks indeed.

[paulzig]

Very nice mate..Wish my Asus Maximus Extreme would hit over 550FSB...

[TheKarmakazi]

If you did a clean install and some copy wazaa I bet you could close in on 8 min 30 sec 32M

[lukas69]

Great score

[natedog420]

nice clocks man. give it some more vcore

[runmc]

nice fsb on the DFI P35

[Bullet92]

great score with xp for daily use... expecting some scores with tweaked xp

and great fsb for UT

[Kean]

Very nice clocks!
Can you tell us about your settings used to hit 608 fsb?

[Oliver]

Looks good, but u can 4 sure see better 1m and 32m time... Go work on it

Keep pushing it.

[breakfromyou]

I heard good things about those boards :p

[Solarfall]

hey DDA wanna share your voltage settings\ other bios settings

[DDA]

tks all

no secrets, we are here to share our experiences and findings

for my ram

- all precharge to act 5
- performance level 8
- trrd 4
- trtp 4
- gtl ref, 72/72/70

voltages, most of all to max; fyi, vcore was set in bios at 1,94; probably cpu-z went nuts

[gandalfone]

Nice Clock DDA

[PcCI2iminal]

the DFI seems to be the best P35 based mobo for the Wolfdale.

congrats and keep pushing

[mrcape]

Is there anything besides Commando that comes close to this board for Wolfdale?

[rgkpt]

nice results keep pushing

[runmc]

tks all

no secrets, we are here to share our experiences and findings

for my ram

- all precharge to act 5
- performance level 8
- trrd 4
- trtp 4
- gtl ref, 72/72/70

voltages, most of all to max; fyi, vcore was set in bios at 1,94; probably cpu-z went nuts

You set all the votages to max? How did you cool chipset? Stock cooling?

[Boogerlad]

nice job!

[DDA]

You set all the votages to max? How did you cool chipset? Stock cooling?

cs stock; ambient 18°, 3 fans 120mm blowing all over the mb

[Razer]

Very nice results DDA

Here is what I managed on my DFI LP UT P35 and E8400 (Q739 ES)



http://valid.x86-secret.com/show_oc.php?id=364171

So, 600MHz, but with multi 6, totaly unstable, unfortunatelly.

I can boot from BIOS on 590MHz, and run 1M on 580MHz.

My settings were:

SB: 1.15v
PLL: 1.75v
NB: 1.77v
VTT: 1.45v
GTL: 90/89/89

Everything was on air

Cheers

P.S. one quick question - my board doesn't boot if VID voltage is set higher then 1.44v (so with 1.45 it doesnt boot),
then I tried raising offset, and same thing happed, but I can raise i to ~104%, higher then that - board won't boot.

So max voltage I can give is 1.53v Any suggestions, I'd be gratefull, and sorry on OT, DDA.

[DDA]

Very nice results DDA

Here is what I managed on my DFI LP UT P35 and E8400 (Q739 ES)



http://valid.x86-secret.com/show_oc.php?id=364171

So, 600MHz, but with multi 6, totaly unstable, unfortunatelly.

I can boot from BIOS on 590MHz, and run 1M on 580MHz.

My settings were:

SB: 1.15v
PLL: 1.75v
NB: 1.77v
VTT: 1.45v
GTL: 90/89/89

Everything was on air

Cheers

P.S. one quick question - my board doesn't boot if VID voltage is set higher then 1.44v (so with 1.45 it doesnt boot),
then I tried raising offset, and same thing happed, but I can raise i to ~104%, higher then that - board won't boot.

So max voltage I can give is 1.53v Any suggestions, I'd be gratefull, and sorry on OT, DDA.

i had same issue; reflashed bios and OK
give GTL 72/72/70

[Razer]

Thanks for the tip, will try that

BTW how much should I give for VTT? Is it 1.45v fine, or should I lower it?