Take3: Asus P5B Deluxe + E6300ES + G.Skill HZ + TT Big Typhoon = 100% OC rolleyes heh

[dinos22]

CPU: E6300 Step5 B1 (Second one)
Motherboard: Asus P5B Deluxe (Bios 0607 BETA)
RAM: 2GB G.Skill PC6400 HZ
Cooler: TT Big Typhoon

No mods
Stock MCH
Stock FSB volts

FIRST WINDOWS BOOT!!!
3.5GHz CPU >> 500MHz FSB 1:1 32M SuperPI one instance 1.35vcore bios (1.3V in windows load; 1.32v IDLE)






How often do you see a 100% overclock on air cooling (well 99.5 heh)

[dinos22]

514MHz FSB 3.6GHz CPU 1.45V BIOS ~ 1.4V Load Windows
DUAL 8M SuperPI >>> HZ sticks 4-4-4-12 2.3vdimm




514MHz FSB 3.6GHz CPU 1.45V BIOS ~ 1.38V Load Windows
30 minutes Orthos Prime >>> HZ sticks 4-4-4-12 2.3vdimm

[dinos22]

did some RAM testing

G.Skill HZ 2GB Kit
543MHz 4-4-4-12 2.45v (2.4v windows >> according to gotherblues asus undervolts at this setting to around 2.2v >> but i haven't measured)

Single 32M SuperPI


Dual 32M SuperPI






Bios Settings Template for you all to give you a rough idea ..... hope it helps,,,,you can use this when benching you rig and recording settings>>> kinda hard to remember it all heheh


AI Tuning: Manual
CPU Frequency: 266- whatever (depending on OC i'm at) >> i do use 398 a bit because of strap change and clockgening
DRAM Frequency: DDR2-533 (1:1 at the moment due to this piece of not being able to run 4:5 divider properly )
PCI Express Frequency: 100
PCI Clock Synchronization Mode: 33.33Mhz
Spread Spectrum: Disabled
Memory Voltage: 2.1-2.45v depending on frequency.............i normally give just enough for it to run stable....i never shove max volts when OCing
CPU Vcore Voltage: ALWAYS SET THIS VALUE ......range 1.35-1.675
FSB Termination Voltage: Auto
NB Vcore: AUTO>>>>i've also jacked this one up all the way for high clockgen frequencies
SB Vcore (SATA/PCIE): AUTO>>>>i've also jacked this one up all the way for high clockgen frequencies
ICH Chipset Voltage: AUTO

Memory Remap Feature: Disabled
Configure DRAM Timing by SPD: Disabled
DDRAM CAS# Latency: 4
DRAM RAS# to CAS# Delay: 4
DRAM RAS# Precharge: 4
DRAM RAS# Activate to Precharge: 4>>>considerable impact on performance and stability
DRAM Write Recovery Time: 2
DRAM TRFC: 20>>>considerable impact on performance and stability
DRAM TRRD: 3
Rank Write to Read Delay: 9
Read to Precharge Delay: 7
Write to Precharge Delay: 9
Static Read Control: Disabled

Modify Ratio Support: Enabled
Ratio CMOS Setting: 6-9 (mainly max multi of course)
CIE Support: Disabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Disabled
CPU TM function: Disabled
Execute Disable Bit: ENABLED (occasionally better FSB with this don't know why hehe)
PECI: Disabled

[ncsa]

Amazing stuff ... very well done

[ScottFern]

I thought the new BIOS that was out was 0507? Is there a 0607 bios out?? I am confused?

[Ferry82]

I thought the new BIOS that was out was 0507? Is there a 0607 bios out?? I am confused?

Did you had more fsb then 0507 Dinos22? please tell us

Nice scores mate.

[Direwolf]

Very awesome, hope I can get similar

[dinos22]

thanks guys

i just got the motherboard and CPU put together today first time so i found the latest beta bios which is 0607 and that's the only bios i've used so far

[Chri$ch]

i need a e6300 es

[dinos22]

you can have mine >>> i've going to pickup an E6600 in a couple of days lol

[Thoroughbred b]

That's what I call a monster mboard!!!!

Mine is coming in 2 day's,can't wait

Max with DS3+6400 was 3880Mhz fully stable,hope to get even closer to 4Ghz with Asus

Anywayz,mine DS3 doesn't like Micron D9GMH

[kiwi]

It is a wasted cpu don't you agree?
It would do miracles if it had unlocked multi but you will be fsb limited

Unless 1 day we see 7x650

[JayG30]

OK few questions for you to help me understand where my temps stand right now. Those ~30C temps are I'm guessing at idle. Is your system in the case? If it is in a case could you tell me if those temps are with the side open, how many fans and approx. what RPM. Also is the BT using the stock fan?

Reason I'm asking is the lowest temps I've seen on my setup (E6400 and BT/stock fan) was 34-35C I think. And that was with no OC with the side of the case open and the 2 120MM fans at medium speed. I didn't lap the bottom of my heatsink but I did do some lapping on the IHS (I think I need to do some more actually).

I'm going to update to this beta BIOS I think and OC this thing to see what temps I get. If they are incredibly different then yours then I guess I'm going to have to lap everything better. If that doesn't work I don't know what to do.

Anyway I'd appreciate your help and those are some awesome results.

[Ferry82]

OK few questions for you to help me understand where my temps stand right now. Those ~30C temps are I'm guessing at idle. Is your system in the case? If it is in a case could you tell me if those temps are with the side open, how many fans and approx. what RPM. Also is the BT using the stock fan?

Reason I'm asking is the lowest temps I've seen on my setup (E6400 and BT/stock fan) was 34-35C I think. And that was with no OC with the side of the case open and the 2 120MM fans at medium speed. I didn't lap the bottom of my heatsink but I did do some lapping on the IHS (I think I need to do some more actually).

I'm going to update to this beta BIOS I think and OC this thing to see what temps I get. If they are incredibly different then yours then I guess I'm going to have to lap everything better. If that doesn't work I don't know what to do.

Anyway I'd appreciate your help and those are some awesome results.

And please tell us your results with the new bios

[JayG30]

And please tell us your results with the new bios

I'll see what I can do. Busy day today. Might get a chance late tonight. I'll try to report whenever I get a chance though.

[fhpchris]

you can have mine >>> i've going to pickup an E6600 in a couple of days lol

Lets see some 1.5v-1.65v tests on the typhoon

[M.Beier]

hehe, nice air cooled

hehe, dinos22, some days ago in the danish conroe thread on another forum, I wrote "I'll give a beer if one of you can find me a E6600 I cant get to do 3.6ghz benchable on aircooling, or a E6300 I cant get 100% overclocked, not with air though =)"
You've just made me sure thats a realistic promise SS should be effecient for E6300 no need for DICE or LN2 for 100%

[idiotec]

Man, just amazing results. On all three fronts:

e6300 - Monster
P5B - Monster
HZ's - Monster

One hell of an OC man

[JoeBar]

Very, very nice!

[Ferry82]

I'll see what I can do. Busy day today. Might get a chance late tonight. I'll try to report whenever I get a chance though.

I already flashed it could not wait

The bios is running fine but cannot do anything more then 0507 can.

[vintage_guitar]

are you using a SATA hard drive or IDE? my DS3 crapped out at very low clocks due to IDE....retarded

[kiwi]

Because there is no native IDE support, there is Jmicron PCIe to sata raid + ide controller. However, I don't remember having problems using raid + oc, so I don't think it is because of IDE

[dinos22]

thanks guys

about cooling i use a case of course and TT BT with a Panaflo 100CFM fan at high speed for benching

using a sata drive yes

one thing i noticed with this setup is how aweful the vdroop is...........i'm talking up to 0.07v TERRIBLE

M.Beier you owe be a beer

[dinos22]

Lets see some 1.5v-1.65v tests on the typhoon

board is done at ~530 FSB.......so no go this CPU would have no problem going to 4GHz benchable

[JayG30]

sorry for beating a dead horse but case door closed for those results or open? Reason I'm asking is I noticed a nice jump in my temps when my case is closed so I'm curious if those temps were from a closed or open case.