which memory should i use (Â£200 budget)

**keiph** · 08-01-2005, 02:39 AM

hi everyone ,i would like to have some surgestions on what memory to use as i keep getting told a different one each week and the computer is near complete.

I have LS+LAIN-LI
TURBO-COOL 510
3800+
*A8N-SLI
* PAIR 7800GTX
* PAIR WD740
+(*water cooling)
I would like to be able to overclock ,but still need to use on everyday stuff(ebay)
i have a budget of Â£200 and would like to know if i have to buy more than 1gb of memory to get best results

**smids** · 08-01-2005, 09:28 AM

Welcome to the forums

. Firstly, do you play BF2? The problem with 2GB is timings at the moment. The Corsair stuff has a Cas2 @ 200mhz but Corsair and nF4 has shownb to be a bit of a no-no for a fair few people. Look into OCZ or GeIL 1GB sticks perhaps. I would say that 2GB would be nice but I went for the cheaper 1GB option. Cost me Â£74 from Komplett for 2 x512mb sticks of BH5-UTT stuff. They are now running at 237mhz 2-2-2-5 1T, not bad for less than Â£75 but requires active cooling (120mm blowing over it). For Â£200, you can easily get anything. Personally, I'd go for some UTT stuff and tight timings over 2GB unless you intend to play BF2 whereby 2Gb is really necessary. You don't say which CPU. If it's an X2, get 2GB, single core, maybe 1GB unless you play BF2. Hope this helps you somewhat.

**keiph** · 08-02-2005, 06:36 AM

Thanks Smids,no don't play bf2 ,theirs some nice ocz on e-bay will running dual make any dif to what typ i buy?
.i will go for BH5-UTT what name are thay under?

**sdkevin** · 08-02-2005, 07:04 AM

Mushkin Redline XP4000 is UTT

**OV3RCLOCK3R** · 08-02-2005, 07:04 AM

Ocz rev.2 or g.skill for high fsb and i've pm'ed you aswell

**smids** · 08-02-2005, 07:15 AM

Originally Posted by sdkevin

Mushkin Redline XP4000 is UTT

That's the expensive stuff. I've just got TwinMOS Speed Premium 3200 BH5-UTT which so far does 250mhz @ 3.28V. I haven't really pushed them yet. Have a look in the thread which has a listing of all UTT RAM and choose yours from there really. The Redline's would set you back about Â£170 so I didn't go for them and chose a cheaper option which in my view is just as good.

**keiph** · 08-03-2005, 02:33 AM

hi everyone, just read that utt means untested do's this mean that it add's no value to the memory and is only a fact of condition?
i found some geil ddr400/3200,(gow1gb3200dc) was told by djbbenn what this is ok on my board anyone tell me about it's attributes.(anyone use'in it or used it)

**Eloxxd** · 08-03-2005, 02:41 AM

Originally Posted by sdkevin

Mushkin Redline XP4000 is UTT

i thought mushkin redline are UTT CH ?

**smids** · 08-03-2005, 02:42 AM

Hmm, not sure about that memory. What brand is that? UTT memory does just mean what you said. The Redline XP4000 UTT is actually tested but it retains its general UTT tag. UTT often clocks very well but then again it's not guaranteed and also you can get some duff chips - I have 4 sticks of UTT stuff and none of them are bad. Most RAM will work with your board, just don't use Corsair on nF4 boards. Hope this helps.

**smids** · 08-03-2005, 02:43 AM

Originally Posted by Eloxxd

i thought mushkin redline are UTT CH ?

I'm pretty sure it's BH because CH isn't rated as high a voltage as the BH due to the fab process. The Redlines are rated up to 3.5v under warranty.

**Eloxxd** · 08-03-2005, 02:46 AM

in this memorydb they are listed as utt ch-5
http://www.techpowerup.com/memdb/

**smids** · 08-03-2005, 02:48 AM

Originally Posted by Eloxxd

in this memorydb they are listed as utt ch-5
http://www.techpowerup.com/memdb/

I see your point. Hmmm, weird as they are rated @ 2-2-2-X whereas CH is usually 2-3-2-X. Obviously it can do 2-2-2-X

Maybe someone with Redlines can confirm either way??

**keiph** · 08-03-2005, 02:53 AM

hi, it's GEIL? ONLY NAME ON IT ANY GOOD.

**//mAr** · 08-03-2005, 03:24 AM

Originally Posted by smids

I see your point. Hmmm, weird as they are rated @ 2-2-2-X whereas CH is usually 2-3-2-X. Obviously it can do 2-2-2-X

Maybe someone with Redlines can confirm either way??

It's UTT-CH-5 because they can't run 200Mhz @ 2-2-2 with 2.6 - 2.8v... UTT BH-5 Can do....

**keiph** · 08-03-2005, 03:41 AM

HI,I 'am back fat because i found some mushkin within my budget
1:mushkin SPECIAL 222 L11 V2(2-2-2-5 1GB)2.5-2.8/400Mhz.
2: " REDLINE XP4000 DDR500 BH-6 MODEL 991440(2-2-2-5 1GB)3.3v-3.5v.
i know you all like the red line on is this it it's well in my buget (Â£150.00).

**keiph** · 08-03-2005, 04:39 AM

hi. again before i buy looks like my a8n-sli only has ,cas#latency(tcl) (auto),(2.0),(2.5),(3.0).
will this mean i car'nt get the benafit's? .should i go for somthing else?
fell like am lost again.

**LivingL@rGe81** · 08-03-2005, 06:50 AM

I would go for G.Skill GH, you are virtually guaranteed 250 2-2-2-? @ 3.2-3.3V, any save about 15% or more on the redlines

**keiph** · 08-03-2005, 07:19 AM

HI, my board max out at(3.0) (a8n-sli)unless i can get a newer bios that let's you go higher?

**keiph** · 08-03-2005, 03:14 PM

hi,"THANKYOU EVERYONE FOR YOUR HELP" ,It looks like a bought a pig ,iam putting it up for sale tomor'a (the mobo won't do 2gb lan), just won't get the best out'a my vapchill on this.
gon'a buy a lan party ut nf4 sli-dr (find a good price first) will look on the boards for the best unless you agree that's the best for OC at the moment.Thanks again and sorry it was a waste of your time ,Keiph

SUGAR LEVELS TO HIGH OVERCLOCKED MYSELF

**smids** · 08-03-2005, 03:58 PM

Ultra-D here. Very happy user

Thread: which memory should i use (Â£200 budget)

Thread Tools

Search Thread

Rate This Thread

Display

which memory should i use (Â£200 budget)

Bookmarks

Bookmarks

Posting Permissions