Mushkin Redline XP4000 in action again!!

[ben805]

great results there Ben - would you happen to have a link for that new A64 Tweaker... 0.60? Latest i have is .50XT. Thanks!

thanks

here's the 0.60 beta:
download

[ben805]

I did the sense wire mod with 141 ohm fixed-resistors and now I can crank this 3.3v rail all the way up to 3.99v, OVP kicked in at exactly 4.0v so I left it at 3.95v, useable vdimm is 3.7v but I only need about 3.5v, I'd also bumped up the 12v rail for more stability. The maximum rock-stable memclock for 3.5v vdimm is 265 @2-2-2-6 1T, this time around I have to use slightly different Dram drive and data strength, no problem with memtest, OCCT, 3dmark loop, and superpi 32m at 27m 06s





nevermind the vcore....didn't bother to back it down

[fareastgq]

nice results ben, the beginning of your post is like the exact opposite of mine, laf, u should check out my ram timings, I just updated my post. U might find a bit of it useful.

[TEDY]

w000t

mushkin Redline XP4000 1GB (2 x 512MB) 184-Pin DDR SDRAM DDR 500 (PC 4000) Unbuffered Dual Channel Kit System Memory Model 991440 - Retail

Cas Latency: 2
Heat Spreader: Yes
Manufacturer Warranty: Lifetime
Timing: 2-2-2
Voltage: 3.3V-3.5V

Model #: 991440
Item #: N82E16820146392

Out Of Stock
$4.33 FedEx Saver Shipping
Move To Wishlist
$199.80
Out of stock

[ante_ante]

Try www.pc-memory-upgrade.co.uk instead, they have in stock. Will recieve mine tomorrow

[TEDY]

sure they're in stock but prices are sky high....really great to buy stuff in UK ....NOT

200€ just for REDLINE 3200 .....OMG

that's JUST TOO HILARIOUS

PFFF

236€ REDLINE 3500
260€ REDLINE 4000 - in GERMANY you can get it here for 195€

http://www.cheeep.de/chips.php?op=mo...2193.95.239.77

UK = SUX

ouch

1€ = 1.2$

so it makes 310$ for PC4000 LOL

[EMC2]

I did the sense wire mod with 141 ohm fixed-resistors and now I can crank this 3.3v rail all the way up to 3.99v, OVP kicked in at exactly 4.0v so I left it at 3.95v, useable vdimm is 3.7v but I only need about 3.5v, I'd also bumped up the 12v rail for more stability. The maximum rock-stable memclock for 3.5v vdimm is 265 @2-2-2-6 1T, this time around I have to use slightly different Dram drive and data strength, no problem with memtest, OCCT, 3dmark loop, and superpi 32m at 27m 06s

Very nice Only lost 5Mhz going from 3.7V to 3.5V I'm getting very tempted to grab some of that Redline sweetness.

/me fights the urge to add to the collection

Peace

[Dumo]

Really good memory ....but the cold boot I have to play plugNpull with 4 sticks on my mobo

[EMC2]

Really good memory ....but the cold boot I have to play plugNpull with 4 sticks on my mobo

plugNpull...

Hopefully DFI will come out with a new BIOS that initializes the Vmem circuit at cold boot like it should...

Peace

[Craig]

sure they're in stock but prices are sky high....really great to buy stuff in UK ....NOT

200€ just for REDLINE 3200 .....OMG

that's JUST TOO HILARIOUS

PFFF

236€ REDLINE 3500
260€ REDLINE 4000 - in GERMANY you can get it here for 195€

http://www.cheeep.de/chips.php?op=mo...2193.95.239.77

UK = SUX

ouch

1€ = 1.2$

so it makes 310$ for PC4000 LOL

OMG! $310 US for Redline 4000! Monarch has it for $191 & free shipping now. I just don't understand why everything costs so much in EU, a differance of $120 is crazy! Just not right, feel for you guys.

[ben805]

Very nice Only lost 5Mhz going from 3.7V to 3.5V I'm getting very tempted to grab some of that Redline sweetness.

/me fights the urge to add to the collection

Peace

they're great....and I hope they'll last, for 24/7 I'm running them at 250 @3.1v

Really good memory ....but the cold boot I have to play plugNpull with 4 sticks on my mobo

strange...I haven't experience the cold boot yet, would the cold boot go away if you run only 2?

[Dumo]

strange...I haven't experience the cold boot yet, would the cold boot go away if you run only 2?

Same with 4x512 or 1GB. I used blue mushkin or GH to set 3.4V in bios then plug this redline so many times ..It stays @ 265-273/3.6V at all times for benching ... but sometimes (when I try to push core and mem. on vid. card for particular 3d bench) the system reboot and tahts it ....Plug N Pull again ....

[EMC2]

You find and try your Zippy yet Dumo?

BTW... you have to Plug-N-Pull (that phrase still quacks me up ) after a reboot when AC was not removed?!? First I've heard anyone with that one if so I'ld definitely hunt down that Zippy

Peace

[Dumo]

You find and try your Zippy yet Dumo?

BTW... you have to Plug-N-Pull (that phrase still quacks me up ) after a reboot when AC was not removed?!? First I've heard anyone with that one if so I'ld definitely hunt down that Zippy

Peace

Actually, yes A/C off b/cause raid went bonkers ..have to totally off. Thanks for the guiide EMC2, will drag zippy out of retirement
@Ben, you got a super redline...

[ben805]

thanks I just saw newegg has them onsale for $198... 3 pairs in stock, I just bought another pair, will receive them on Friday so I'll be playing with 4x512MB over the weekend

[EMC2]

Actually, yes A/C off b/cause raid went bonkers ..have to totally off. Thanks for the guiide EMC2, will drag zippy out of retirement
@Ben, you got a super redline...

You couldn't power-down using the on/off switch on the MB bro instead of the AC? You're welcome, hope it helps

[Dumo]

You couldn't power-down using the on/off switch on the MB bro instead of the AC? You're welcome, hope it helps

That exactly what I did, once the power off for 1 second then it wont post

[EMC2]

Hmmmm.... sorry Dumo, apparently I'm not being clear bro, my bad.

By "removing or turning off AC power", I mean unplugging the power supply or turning off switch on back of PS or turning off AC power on a power/surge strip the AC cord of the power supply is plugged into. (the green standby LED in lower left of MB near diagnostic LEDs will go OFF)

By "using the on/off switch on the MB" I mean pressing and holding in the power switch in the lower right corner of the MB, near the SATA connectors. (the green standby LED in lower left of MB near diagnostic LEDs will stay ON... this does not remove AC power, only the main DC power to the MB... the +5VSB is still applied)

ygpm

[ben805]

nevermind the 1T, just found out it can't be done with 4x512MB....duh! I'm going to play around with them and post some results.....

[derprof]

where to buy these in germany?

[ben805]

Here it is....Mushkin Redline XP4000 4x512MB 250 @2-2-2-6 2T 3.2v SuperPI 32M at 26m...I think it's pretty good comparing to my previous run with only 2x512MB

2x512MB




4x512MB




let's see what these puppies can do at 3.5v!!

[ben805]

hot damn!! these Redline XP4000 clock like mad bat out of hell....4x512MB I can run these bad boys at 266 @2-2-2-6 2T with only 3.5v!! pretty tight timing to boot it doesn't look like I lost that much score on SuperPI 32M either

[jiff]

Amazing