phase change gallery

[H2gO Flasher]

I'll take a bob eachway with my Black Phase *Work in Progress*

[wez]

Here is my main rig, only a vapochill SE, but it gets the job done
NB and GPU is watercooled.

[Marvin]

man, good work. Your machine is very pretty.
cheers

[wez]

man, good work. Your machine is very pretty.
cheers

Cheers m8

[MaZeR]

Here's my Lian-Li Mach II mod that in the tradition of the 'Q-cars' I have dubbed 'Q'. I got the cooler second hand and started modding my case straight after getting it. The fit is to 0.5mm tolerances and caused a lot of stress but is fairly complete except for pulling it all apart so I can fit a 3,4C once I get it, doh. The current chip is a fairly slow but game stable 2.4C.



More pics here: http://mazer.sytes.net/Q/

[`schr0et]

wouldn't be fun having to change CPUs with that thing inside the case

What about your case temps wouldn't they go incredibly high with the mach ii in there?

[Cashman]

The Wavemaster has not been cut yet so the the case is not level at.... this is just a teaser for the time being

[MaZeR]

wouldn't be fun having to change CPUs with that thing inside the case

You're not wrong, but that doesn't happen often at all unfortunatly $$$

What about your case temps wouldn't they go incredibly high with the mach ii in there?

Actually temps are unchanged at idle and rise about 7*C above what I would previously get over a long period of gaming at 100% load. It was because of this concern that I have added an extra fan at the rear of the case and changed to Thermaltake Smartfans with higher CFM. These 2 rear fans replace the single 120mm prommie fan and do a good job. Actually, during my last assembly the top blowhole fan became disconnected and I have been too lazy to reconnect it. Once I reconnect it, I would say that the internal temps will not be much of an issue at all.

[Cashman]

Loooks better now its mounted properly

Whats your opinions?

Ive never seen the Curvey lines and the straight ones used together

[Capt MonkeyBoy]

hi'ya

just a quick pic of my vapochill XE, i have moved the psu up in to the top and have water cooled n/b and g-card with a zalman res1, blackice pro2 rad, xice pcp25 pump, dangerden maze4 N/b block and NV68 graphics card block,,,,you can see the rest in my sig.....

...can get 14025'3d03 and 6045'3d05....

[kayl]

its a 1HP rotary running bbq propane at 10HG at full load, idle is below -50c but i need new gauges to tell exact temps, (only read down to -50c)

and prime 95 for fifteen mins
top temp is evap, bottom temp is 6" from accumulator

[Aphex_Tom_9]

hey guys, im kinda a lurker here (im more an ocforums guy) i just got a Prometeia for $420 on ebay partly for my birthday, wanted to add this to the phase gallery here, check it out-

[Cashman]

This picture is not mine, but I was sent the pic... in my opinion its one of the sweetest case/MAch II mods ive ever seen!!

[Aphex_Tom_9]

wow, it is.

[Cashman]

wow, it is.

Its a Coolermaster 201 I think, with another Coolermaster 201 that has been cut in half, inorder to make room for a Mach I.

The Mod and the finish are just awesome tho... that match up sooo well!!

[Vandread]

come on guys there are many more cases that look that good
this is just one of the best looking:
http://home.wanadoo.nl/a.p.versteeg/prom-li-pro
Tom Versteeg has done some kickass casemods ^_^

[Aphex_Tom_9]

yeah, ive seen his work, amazing stuff

[The Byter]

not finished yet..

[thesaucier]

not finished yet..

Very nice but maybe I would like to see alot more than -44 on the evap with a condenser fan that will have to be held in place or it will fly away. I mean I get -41 -42b with a mach one evap temp. Nice work though I am always impressed when you biuld your own. Just asking what did it cost you??

[BuLkHy]

mach's temp probe arent accurate m8..

[The Byter]

The cost ? around 200$~

[Troopah]

Wow... Nice one there Byter, how long did it take for you to make that one?
200$~~ awesome

[The Byter]

around 2 years from start to finish ....
I learned all about it, ordered the baker block from the US, made friends with the ac guy

It was a long journey

[thesaucier]

The cost ? around 200$~

Wow thats great!! very nice.

[Ricarus]

come on guys there are many more cases that look that good
this is just one of the best looking:
http://home.wanadoo.nl/a.p.versteeg/prom-li-pro
Tom Versteeg has done some kickass casemods ^_^

Versteeg is a PRO... they ask him for shows etc.