SuperPi32m 5GHz & 4GHz Z97 Haswell ( Refresh ) All Out Challenge!

[nickshih]

Are these my ex week1208 sticks?

found those in my colleague's desk ... They thought it was junk .

[Splave]

Have to love qualification sticks

[TaPaKaH]

found those in my colleague's desk ... They thought it was junk .

that's not far from truth, actually

[l0ud_sil3nc3]

l0ud_sil3nc3 - 5:56:953 - 50x100.1 - 1467.6 MHz - 9-12-12-17-108-1 - Z97 OCF - Corsair 2666 c10 2x4GB/Samsung - 2.15v - LN2 (-125c/+2c)



and RTL's



Tsai's pot just sitting on top of the Dom Plats, naked and uninsulated, hence why just a quickie run to test these out, will put some more time in it as it feels about a half second off.

[C-N]

Like it

[Calathea]

l0ud_sil3nc3 - 5:56:953 - 50x100.1 - 1467.6 MHz - 9-12-12-17-108-1 - Z97 OCF - Corsair 2666 c10 2x4GB/Samsung - 2.15v - LN2 (-125c/+2c)

Tsai's pot just sitting on top of the Dom Plats, naked and uninsulated, hence why just a quickie run to test these out, will put some more time in it as it feels about a half second off.

That's +2?C on the sammies?

[l0ud_sil3nc3]

That's +2?C on the sammies?

Yes Calathea, +2c just one run on a completely untested retail 4790K.

The pot was just sitting on the heat spreaders, no TIM or anything. The k probe was wedged in between the spreader and the pcb to get a more accurate reading.

[Calathea]

Yes Calathea, +2c just one run on a completely untested retail 4790K.

The pot was just sitting on the heat spreaders, no TIM or anything. The k probe was wedged in between the spreader and the pcb to get a more accurate reading.

Wow not more for that clock... you definitely got me inspired :P Is cold on cpu necessary you think?

[l0ud_sil3nc3]

Like it

Thanks C-N, your Z87 time is what I'm chasing, but your too fast

Wow not more for that clock... you definitely got me inspired :P Is cold on cpu necessary you think?

For 5000 uncore, most definitely for 4700-4900 air should be fine.

[C-N]

Thanks C-N, your Z87 time is what I'm chasing, but your too fast

He he, that's the aim of the game real good to see 2933.

However I feel a full can coming my way....

[bullant]

Some PSC on air cpu on water,not looking to be added on this one as I went just over cap 4003

[l0ud_sil3nc3]

Some PSC on air cpu on water,not looking to be added on this one as I went just over cap 4003

Now that is a killer IMC + memory combo

Everything super tight as well great job bullant

[Don_Dan]

Update.

Impressive results from l0ud_sil3nc3, Splave, hiwa and Nick Shih!

[Alex-Ro]

alex-ro - 5:58:297 - 50x100.1 - 1466.4 MHz - 9-12-12-21-110-1 - Maximus VII Formula - Corsair Vengeance PRO 2666 c10 2x4GB/Samsung - 2.12v - Air +25c Ambient



First shot on new mems,need to improve efficiency and lower RTL.

[Alex-Ro]

alex-ro - 5:57:891 - 50x100.1 - 1466.4 MHz - 9-12-12-21-110-1 - Maximus VII Formula - Corsair Vengeance PRO 2666 c10 2x4GB/Samsung - 2.15v - Air +25c Ambient

[bullant]

So its been 6 weeks without Ln2,finally received some ln2 today,testing a new 4790K was quite hard to dial this chip in,is so different to any 4770ks Ive tested
Did finally get a pass but was loosing a efficiency towards the end of the session,board seemed to get quite cold on in this session so im guessing some moisture somewhere.
Had a couple faster runs a little earlier that should have just cracked the 54.9xx,will keep trying
bullant - 5:55:266 - 39x128.3 - 1410.8 MHz - 6-10-16-21-64-1 - Z97 OCF - GSkill Pis 2000 cl6 - 2.23v - LN2 -160



This was one of the faster runs,im thinking 54.9xx on this on

[I.nfraR.ed]

Don't know if that's the correct thread.
Also don't know how is my efficiency with this G3258, since there are not many 4GHz runs out there.

Screenshot lacks AIDA numbers, so it does not qualify, thus not writing the info in the correct format too.

All air, 1.92V for the mems - G.Skill 2000C9 Tridents, PSC-X.

[l0ud_sil3nc3]

Awesome runs Bully, glad to see the 125 strap working out for you as well.

The humidity down under looks intense right about now!

Don't think I have ever seen your rig so wet/frosted especially not the SATA ports or PCH heat sink

@ Infrared

here's one to compare:

2666


2736

[I.nfraR.ed]

Thanks, loud
I can't run that tight and it seems I'm 1 second behind.
Anyway, it doesn't matter anymore since it seems my new cpu can't run 2666 and 2600 with PSC even with slack secondaries and tertiaries.
It's either the board or the IMC. I can't even run CAS 7 at 2400, while that's way too easy on Z77 + 3770K with these sticks

Wish I had any other brand board to try...

[bullant]

Thanks loud, yeah I've never had it frozen that much before,I say you are correct

[l0ud_sil3nc3]

So this has been my main pi drive for the last year or so, guess it's time to test all my mechanical drives.



Maybe this is why I'm so slow

[websmile]

I use 10 year old sata 1 Seagate in my haswell test rig with lots of bad sectors and I don?t bother

[l0ud_sil3nc3]

I use 10 year old sata 1 Seagate in my haswell test rig with lots of bad sectors and I don?t bother

Do you think it matters at all? (i.e. performance wise)

[websmile]

Not really, you normally try to avoid that hdd is involved in 32M, I also don?t use ram disk if I bench on time, which I didn?t on Haswell anyway

[TaPaKaH]

CW is much faster using SSD than HDD. So if you do it like 100 times per month and save 5 mins each time, it amounts to ~8 hrs of extra free time that you can use
Performance and stability-wise I see no difference at all having recently switched from HDDs to SSDs.