SuperPi32m 5Ghz Ivy All Out Challenge!

[l0ud_sil3nc3]

If the second 2133C8 kit is also owned by Allen's Avantium that fail 1200 8-10-7 on air (which is very likely) then BBSE binning becomes a clear issue. If you start looking for bad air kits then you'll end up with stuff that fails 1066 9-9-9 and I bet is equally bad cold. And testing each kit on LN2 is not very practical from time/money/resale viewpoint.

All hopes now on PSC at being more consistent...

Your green pcb kit ran 2600 8-11-7-22 everything else super tight and tWCL 6 at 1.9v with no issues on air, so it is definitely a good kit.

I just hope the black PCB scales with voltage and does not hard wall.

It seems PSC is also susceptible to this voltage wall but it is much more rare to see.

Thinking back, I probably should have stuck with 8-9-6-18 and pushed upwards towards 2700+ will keep this mind if the other kit does not cooperate

[TaPaKaH]

Thinking back, I probably should have stuck with 8-9-6-18 and pushed upwards towards 2700+ will keep this mind if the other kit does not cooperate

Am not fully sure if -85..-100 is enough to support tRCD 9 all the way to 1350. Also, tRP 6 and tRAS 18 look very tight at 1300 already.
If you feel like it, give 7-10-7 tWCL 7 another shot I reckon that's where "no fully liking cold and volts" BBSE might be best at

[XBrytanX]

Sam's BBSE under cold ->take 2 (one of them might be wounded -constant 55 at the end )

[nachtfalke]

g.skill 2133cl8 /KPC ney pro /LN2 -170
cpu/ss
i will rebench soon ....

[Splave]

Nice pics

[nachtfalke]

Thanks! I had some unexpected problems , it was first LN2 session including RAM...so was not easy ...and as know bbse is not very easy to bench
they fail to boot on air over 1.84v, but under cold was fine 2,050v no problem
1300 7-9-6-18 trfc 68 1T pass 32m without wazza , with wazza "not exact in rund" loop 10 - 15

[XBrytanX]

^ .."i will rebench soon ...." I bet you will ,nice RAM and great results

[nachtfalke]

nachtfalke - 6:16:766 - 49x102.1 - 1327MHz - 6-10 -6-26 Maximus V Extreme/bios0021 -G.SKILL Trident 2000 9-9-9-24 1.6v(( PowerChip XEH) 2x2GB - 2.14v - Cpu@SS -45c/RAM -120c LN2

Kingpincooling Ney Pro -awesome pot, 6 hours session.. i will rebench for a better score

[Splave]

Noiice

[nachtfalke]

nachtfalke - 6:16:406 - 49x102.1 - 1327MHz - 6-10-6-26 Maximus V Extreme/bios0021 -G.SKILL Trident 2000 9-9-9-24 1.6v(( PowerChip XEH) 2x2GB - 2.15v - Cpu@SS -45c/RAM -125c LN2

http://www.youtube.com/watch?v=ncuPlLbGguw



Mandatory pic required

[Alex-Ro]

woo-hoo

[Don_Dan]

Nice runs, nachtfalke, but your CPU clock is slightly too high ( max limit +-3MHz ). When I make the next update I'll add your results but I'll mark the CPU clock like I did with crusty's result.

[nachtfalke]

yes, but i am no fault that clock generator on m5e( or asus board) is so , in bios it is 49x102.1=5002( you can check)
thank you anyway

[maxxx]

Sorry for being out of topic, but anyone have any link in insulating the memory area of a board? Thanks!

[hiwa]

Sorry for being out of topic, but anyone have any link in insulating the memory area of a board? Thanks!

http://kingpincooling.com/forum/showthread.php?t=727

[maxxx]

@hiwa: thanks. pics are not loading though.

[nachtfalke]

http://extreme.pcgameshardware.de/ex...ml#post5290798

[maxxx]

@nachtfalke: Thanks for that link man. Now have some idea....

[bullant]

maybe 15s ,was .150 better then my .219 at 21 loop

[Splave]

hurry bro, looks like we will be talking about 5:59.*** soon XD

[hiwa]

bullant u have 10 days to finish this .

[Alex-Ro]

This can go on after haswell launch too

[bullant]

Only have about 8 lrts left of ln2 then it have to wait awhile,I may be bit late starting on Haswell so I have to mess with ivy until I get some Haswell gear

[dinos22]

stunning

[bullant]

Fresh windows install
bullant - 6:16:094 - 102x49 - 1327.3MHz - 6-10-6-27-90-1 - Gigabyte Z77X-UP5TH -G.Skill Pi 2000C6 4X2Gb/PSC - 2.1v -CPU SS -30 / Memory LN2 -120