Worklog - Nadeshiko

[ohms]

I'm so glad you bought better looking air filters, those old blue ones were horrible How are those DeciM filters? I was looking at them on PPCs, since I'm looking into some decent filters for my cube build.

ROFL! Holy that is loud.

[NaeKuh]

I'm so glad you bought better looking air filters, those old blue ones were horrible How are those DeciM filters? I was looking at them on PPCs, since I'm looking into some decent filters for my cube build.

ROFL! Holy that is loud.

LOL tell me about it...

its cuz all 6 san aces will rev 100% when my cpu hits anything close to 33% utilization.

Now u see why i want to pull the PWM off the video card.. :P


as for the DeciM... i like them... they get dirty really really fast tho.. but its so easy to clean i dont mind.
however i still have problems with fine dust laying on the top chamber floor...

[ohms]

LOL tell me about it...

its cuz all 6 san aces will rev 100% when my cpu hits anything close to 33% utilization.

Now u see why i want to pull the PWM off the video card.. :P


as for the DeciM... i like them... they get dirty really really fast tho.. but its so easy to clean i dont mind.
however i still have problems with fine dust laying on the top chamber floor...

I don't think you can ever get rid of the fine dust short of surrounding your PC with your jury rigged air filters and even then I can imagine some getting thru.

How did you get the fans to work like that btw? AE4?

Sent from my SCH-I500 using Tapatalk

[ximius]

LOL tell me about it...

its cuz all 6 san aces will rev 100% when my cpu hits anything close to 33% utilization.

Who wants to start a pool to see how long it is before we cant see those fans through the filters there?

Any takers?

[Rubycon]

IMHO you would be better off managing the air quality of YOUR room (living space) then turning your PC into an air filter. It will be better for YOU as well!

The wrinkle finish on MM cases is probably the most durable but it's also a dust/dirt magnet and you really have to literally scrub it clean!

As far as getting lower temps I've told you what you need to do about chilling your water and controlling temps to prevent condensation and eliminating the need for conformal insulating coatings on the motherboard, etc.

About that HUD - yes it's possible. There's plenty of software that will do it with a simple laser diode arrangement. If you want purple it will cost a lot more due to the complexity in getting that color. If red is OK well that's basically peanuts.

[NaeKuh]

How did you get the fans to work like that btw? AE4?

Sent from my SCH-I500 using Tapatalk

pwm rheobuss.

http://www.performance-pcs.com/catal...ducts_id=30057

[ohms]

Ao ok, so the Rheobus 4-pin goes to pwm 4- pin on the motherboard w which controls the throttling based on CPU usage?


Sent from my iPad using Tapatalk.

[Utnorris]

Just curious as too how many of those San Ace fans will connect to a single channel on that controller Naekuh? I still have a bunch, but switched over to Triberks due to the noise, they are quieter at low RPM and still seem to push air like the San Ace fans. The only real issue is finding screws for them unless I want to retap all my rads to 8-32 like you did.

[NaeKuh]

Ao ok, so the Rheobus 4-pin goes to pwm 4- pin on the motherboard w which controls the throttling based on CPU usage?
.

exactly... those 2 cycles of 100% rev's u heard is my system going though linX.

The pause in the middle is when the fans quiet down... and then the full load is when my cpu has 100% load.

Just curious as too how many of those San Ace fans will connect to a single channel on that controller Naekuh? I still have a bunch, but switched over to Triberks due to the noise, they are quieter at low RPM and still seem to push air like the San Ace fans. The only real issue is finding screws for them unless I want to retap all my rads to 8-32 like you did.

30W max per channel = 2.5amps.
.52amps / fan.... x 3 = 1.56amps... x 2 = 3amps @ startup.

I assume ur safe with 6 fans on 2 channels.
Since its only startup that pulls more.

But i wouldnt load 9 san aces on it...


My thoughts on tribewers..
I wont be able to type it without u getting spam'd banana's.. lol..
And reason why it would be spam'd banana's is exactly the same reason as u say.

Impossible to find working screw for it.



EDIT:
i got yelled at by skinnee last night for leaving the box fan running in the background.
Most of the background noise u guys hear is the box fan.
I'll redue the video with the box fan turned off later today.

[miahallen]

My system sounds halarious.. noise wise... as i game.. the fans rev up... and i go on idle mode.. its pretty quiet..
But here is a sample of what i mean:

You play games? I thought you built this to surf forums

[Utnorris]

Thanks for the info. I will listen to your video once you redo it, that might convince me to go back to my San Ace fans, although I am starting to hate sleeving.

[NaeKuh]

You play games? I thought you built this to surf forums

all this power just to surf forms would be comedy...

Im a gamer at the core... no doubt about it.

Thanks for the info. I will listen to your video once you redo it, that might convince me to go back to my San Ace fans, although I am starting to hate sleeving.

mmm... i redid the video.. but it doesnt sound any cleaner... u can hear the birds chirping in the background tho.
http://s125.photobucket.com/albums/p...ent=MOL001.mp4

Man... all this tuning... i kinda felt like i was at a dyno with my friend listening to them rev the engine...