ASUS P8P67 Pro/Evo/Deluxe OC discussion thread

[ghmz]

What is your RAM kit, and at what speeds and timings are you running it? It indeed seems your memory is not stable.

I have this RAM. Running rated timings which are 9-9-9-24-2N, 1.5V.

[Darkstormz]

I´ve got some serious issues going on my P8P67 WS Revolution.

When I run 3DMark Vantage / 3DMark 11, I get a message "Nvidia display driver stopped responding and has recovered"

Tried everything, GTX480, GTX580 and 9600GT card. Still same problem.
Tried to switch PSU from Corsair HX620 -> Corsair AX850. Still same problem.
Re-installed Win7 Ultimate SP1 and still got the same problem.

Sometimes I can run 3DMark for 30sec, sometimes a couple of minutes.
The most strange thing is: Can run Unigine Heaven benchmark for 30min without any trouble.

Everything is at stock 2600K, 16GB Vengeance 1866MHz...

Anyone?

[McLaren__F1]

I´ve got some serious issues going on my P8P67 WS Revolution.

When I run 3DMark Vantage / 3DMark 11, I get a message "Nvidia display driver stopped responding and has recovered"

Tried everything, GTX480, GTX580 and 9600GT card. Still same problem.
Tried to switch PSU from Corsair HX620 -> Corsair AX850. Still same problem.
Re-installed Win7 Ultimate SP1 and still got the same problem.

Sometimes I can run 3DMark for 30sec, sometimes a couple of minutes.
The most strange thing is: Can run Unigine Heaven benchmark for 30min without any trouble.

Everything is at stock 2600K, 16GB Vengeance 1866MHz...

Anyone?

You have the latest drivers?

[Darkstormz]

You have the latest drivers?

Yes I do, still the same trouble...

[Darkstormz]

I´ve got some serious issues going on my P8P67 WS Revolution.

When I run 3DMark Vantage / 3DMark 11, I get a message "Nvidia display driver stopped responding and has recovered"

Tried everything, GTX480, GTX580 and 9600GT card. Still same problem.
Tried to switch PSU from Corsair HX620 -> Corsair AX850. Still same problem.
Re-installed Win7 Ultimate SP1 and still got the same problem.

Sometimes I can run 3DMark for 30sec, sometimes a couple of minutes.
The most strange thing is: Can run Unigine Heaven benchmark for 30min without any trouble.

Everything is at stock 2600K, 16GB Vengeance 1866MHz...

Anyone?

I did a clean install without SP1, and the issue is gone. But as soon as I install SP1, boom! Display driver stopped blabla....

[crossg]

I did a clean install without SP1, and the issue is gone. But as soon as I install SP1, boom! Display driver stopped blabla....

I've seen that issue 5 times today, but it's because I'm pushing my Cpu and Gpu's to their limits and 3DMK 11 really stresses the card more than the cpu. Happens on my 980X rig as well so it's probably vid card related. Right now I'm using beta 270.51 drivers but any driver so far has done the same when pushed.

[PJD]

I've seen that issue 5 times today, but it's because I'm pushing my Cpu and Gpu's to their limits and 3DMK 11 really stresses the card more than the cpu. Happens on my 980X rig as well so it's probably vid card related. Right now I'm using beta 270.51 drivers but any driver so far has done the same when pushed.

How are you keeping your temps so low? I'm running a custom water loop and at 1.36vcore it hits 73C. I've reseated the block 3 times and no difference. I have my setup at 4.7GHz with everything set at AUTO except for manual vcore and dimm. I found LLC is a must unless you want a 1.55vcore. I had set mine at HIGH until I found I needed almost 1.38v to run Prime95, but I currently have it set at Ultra High and running at 1.36v but like I said the temps are too high at 73C. I'm thinking of going to LLC = Extreme and dropping vcore to 1.35 or maybe 1.345 to get th temps down.

[crossg]

How are you keeping your temps so low? I'm running a custom water loop and at 1.36vcore it hits 73C. I've reseated the block 3 times and no difference. I have my setup at 4.7GHz with everything set at AUTO except for manual vcore and dimm. I found LLC is a must unless you want a 1.55vcore. I had set mine at HIGH until I found I needed almost 1.38v to run Prime95, but I currently have it set at Ultra High and running at 1.36v but like I said the temps are too high at 73C. I'm thinking of going to LLC = Extreme and dropping vcore to 1.35 or maybe 1.345 to get th temps down.

That was a quick bench and if I tried to run prime at that voltage it would overtemp within the first minute. Mine would probably be around or over your temps with 1.35 volts.