UnOfficial EVGA X58 Classified Owners Thread

[M_T_M]

The problem is the same.Pictures in the game just stops but no BSOD and I have to reset the computer. This happens after 15min, but only in the game BBC2. In other games, everything is ok ( Dead Space2,...). Any idea what could be wrong?

[zsamz_]

The problem is the same.Pictures in the game just stops but no BSOD and I have to reset the computer. This happens after 15min, but only in the game BBC2. In other games, everything is ok ( Dead Space2,...). Any idea what could be wrong?

change v-card driver
but try settin ioh to 1.26v first

p.s you should have your specs in your sig so it would be easier to help

[M_T_M]

I have the latest driver for video card 266.58. This can be a problem for graphic drivers?


CPU: Intel® Core™ i7 980x 4.5Ghz (water cooling with EK HF)
MB: EVGA Classified X58
RAM: CORSAIR DOMINATOR GT 3X2GB 2000Mhz
GPU: eVGA GTX 580 (water cooling with EK-FC580 GTX - Nickel)
SSD: 2x OCZ Vertex 2 120gb Raid0
HDD: 2x Samsung F3 HD103SJ
PSU: Enermax Revolution85+ 1250W
CASE: Corsair Obsidian 800D | G19 & G9 | Acer S243HL | Z-5500 |

[zsamz_]

it can be
cause its doing it with only 1 game
still weird
and post full bios template not picture

AIN	
CPU clock ratio - 
BCLK - 
MCH strap - 
Uncore - 
CPU clock skew - 
Spread spectrum	- 
PCI-E freq -
OC recovery - 
Turbo Performance - 

CPU features	
SpeedStep - 
Turbo - 
C*E - 
executive disable bit - 
VT - 
	
HT - 
Core number -

QPI control settings - 
QPI link fast mode - 
QPI frequency - 
	
Memory  features
Memory frequency - 
CH interleave 
RK interleave - 
Mem low gap -
	
CL - 
tRCD - 
tRP - 
tRAS - 
tRFC - 
Command rate - 
tRRD - 
tFAW - 
tRPT - 
tWR - 
RTL 1 - 
RTL 2 - 
RTL 3 - 
tsrWrTRd - 

Voltage features
Vdroop control - without vdroop
VCORE - 
VTT - 
CPU PLL - 
IOH PLL - 
QPI PLL - 
VDIMM - 
DIMM ref - 
IOH core - 
IOH/ICH/ I/O voltage - 
ICH core - 
VTT PWM freq - 
CPU PWM freq - 
CPU impedance - 
QPI signal comp -

I have the latest driver for video card 266.58. This can be a problem for graphic drivers?


CPU: Intel® Core™ i7 980x 4.5Ghz (water cooling with EK HF)
MB: EVGA Classified X58
RAM: CORSAIR DOMINATOR GT 3X2GB 2000Mhz
GPU: eVGA GTX 580 (water cooling with EK-FC580 GTX - Nickel)
SSD: 2x OCZ Vertex 2 120gb Raid0
HDD: 2x Samsung F3 HD103SJ
PSU: Enermax Revolution85+ 1250W
CASE: Corsair Obsidian 800D | G19 & G9 | Acer S243HL | Z-5500 |

[M_T_M]

how do I do? Do I have to write the voltage?

[zsamz_]

how do I do? Do I have to write the voltage?

how to do?
do i have to answer

[M_T_M]

This si my settings

AIN
CPU clock ratio - 31
BCLK - 146
MCH strap - 2133Mhz
Uncore - 2634(18X)
CPU clock skew - 0ps
Spread spectrum - disabled
PCI-E freq - 100
OC recovery - disabled
Turbo Performance - disabled

CPU features
SpeedStep - disabled
Turbo - enabled
C*E - disabled
executive disable bit - disabled
VT - disabled

HT - enabled
Core number - all

QPI control settings - enabled
QPI link fast mode - enabled
QPI frequency - 6.400gt/s

Memory features
Memory frequency - 1600/ 2:12
CH interleave - 6way
RK interleave - 4way
Mem low gap - auto

CL - 8
tRCD - 8
tRP - 8
tRAS - 24
tRFC - 72
Command rate - 1T
tRRD - auto
tFAW - auto
tRPT - auto
tWR - auto
RTL 1 - auto
RTL 2 - auto
RTL 3 - auto
tsrWrTRd - auto

Voltage features
Vdroop control - without vdroop
VCORE - 1.4125V
VTT - +150mV
CPU PLL - 1.65
IOH PLL - 1.80
QPI PLL - 1.35
VDIMM - 1.65
DIMM ref - 0mV
IOH core - 1.25
IOH/ICH/ I/O voltage - 1.55
ICH core - 1.10
VTT PWM freq - 610KHz
CPU PWM freq - 1333KHz
CPU impedance - Less
QPI signal comp - Less

[zsamz_]

MTM
VTT PWM freq - 610KHz lower to 250
CPU PWM freq - 1333KHz lower to 840

PCI-E freq - 100 set to 101

MCH strap - 2133Mhz lower to 1600
Uncore - 2634(18X) set to 2400(17x)

[M_T_M]

CPU PWM freq - 1333KHz I make 940 because it is at least.
Uncore - 2634(18X) this is at least.

LinX after two minutes shows error with these settings!
I do not know why it does not work prim95?

[zsamz_]

you have bios 77 on?

[M_T_M]

i have bios version 78

[radaja]

Hey folks! I figured I'd give this a shot here as well being the Classified thread and all...

Normally I would not ask many questions when it comes to hardware but this one has got me completely stumped. Basically, I got a new i7 970 a couple days ago and installed it on my EVGA E759 Classified (this is the limited edition board with NF200 chip) running the latest BIOS 77. Before installing the chip I did a full CMOS reset and loaded defaults, powered down the system, and proceeded to install the chip.

Now, I've got everything up and running and the chip is working fine except that no matter what combination I try the turbo multiplier on the chip is not working. I have already verified that it is not working using i7TurboGT, RealTemp, E-LEET, CPU-Z, and CPU Tweaker. I have tried every possible combination of EIST, C-states, and Turbo possible so far with no success. I simply cannot get the 25x multiplier to show up. I've even done multiple CMOS resets followed by setting the appropriate settings, ensuring that I am using the stock multiplier of 24x, etc., with no success.

I'm completely at odds what to do at this point

Any help you can provide I would appreciate! This is stopping me from using the chip to the full potential and I do not know what to do

have you figured this out?i just got a 970 and my E760 does the same,no x25 yet?

[zalbard]

have you figured this out?i just got a 970 and my E760 does the same,no x25 yet?

Needs Westmere mod.

[radaja]

Needs Westmere mod.

do you have any info on this mod?

[zalbard]

do you have any info on this mod?

http://kingpincooling.com/forum/show...2&postcount=21

[radaja]

http://kingpincooling.com/forum/show...2&postcount=21

thanks for the link.i think i will just live with the problem,or get another X58A-UD3R rather than try doing this hardmod.
so far the new 970 is great,doing 21x215@4500 HT on w/1.36v prime 95 stable
linx will need 1.37v i think

[zalbard]

Try silver conductive pen? It's very easy and reliable...

[maxxx]

have you figured this out?i just got a 970 and my E760 does the same,no x25 yet?

I wonder what's the difference between the 970 and a 980x in the eyes of the board? My e762 runs fine with the 980x, but with a 920, it won't run any ram at 2000Mhz, even at loose timings. Its been driving me insane. Using bios 78.

[mk-ultra]

not all CPU have good IMC, you can't put all the blame on the mobo

[maxxx]

@mk-ultra: not that I am blaming the board. I just find it interesting as that 920 works on other boards running 2000mhz ram. Even my e759 runs it better.

[zsamz_]

@mk-ultra: not that I am blaming the board. I just find it interesting as that 920 works on other boards running 2000mhz ram. Even my e759 runs it better.

980x has a stronger imc
759 not as good as the 760 the nfore chip makes it hotter n higher latency
and when you have newer bioses gotta change some settings in ram to run the same

[maxxx]

@zsamz: well, I did try. It just won't boot when the memory is running 2000Mhz or greater. All is good though. I dun plan in trying hard to find out what the problem is. I just used that 920 to flash to the 78 bios and thought of giving it a whirl before putting the 980x in.

[zsamz_]

@zsamz: well, I did try. It just won't boot when the memory is running 2000Mhz or greater. All is good though. I dun plan in trying hard to find out what the problem is. I just used that 920 to flash to the 78 bios and thought of giving it a whirl before putting the 980x in.

i use bios 64
i can run 12gb upto 2060mhz

[maxxx]

i use bios 64
i can run 12gb upto 2060mhz

I didn't try an older bios yet. Maybe it be will worth to try. Thanks...

[gmat]

Is 990x detected properly on latest E770 boards ?