i5-2500K/2600K batch number and o/c results

[st0ned]

I also think that L042B076 it's a go for it!


My 1st L042B076

5.0Ghz with 1.424v not bad :P



But the 2nd one is the best:

1.424v set on bios ( vCore jumping from 1.416~1.432v )

[wekktor]

much lower GFlops on the 2nd.

[st0ned]

much lower GFlops on the 2nd.

800 vs 933 mem freq vs Linx in 4threads vs Linx in 8threads.

[1Day]

Motherboard Gigabyte GA-P67A-UD7

RAM Speed : 1071.3 MHz (1:8) @ 7-7-7-20 (2144MHz)



Validated by CPU-Z 1.56.2



WPrime 1024 mil stable.

[bro20000]

Motherboard Gigabyte GA-P67A-UD7

RAM Speed : 1071.3 MHz (1:8) @ 7-7-7-20 (2144MHz)



Validated by CPU-Z 1.56.2



WPrime 1024 mil stable.

Nice result is it prime stable!

[crossg]

Motherboard Gigabyte GA-P67A-UD7

RAM Speed : 1071.3 MHz (1:8) @ 7-7-7-20 (2144MHz)



Validated by CPU-Z 1.56.2



WPrime 1024 mil stable.

I'm impressed.

[MythSquare]

This is not mine but it deserves some attention:


DIGI+ VRM
Load-line Calibration - High
VRM Frequency - Manual
VRM Fixed Frequency Mode - 480
Phase Control - Extreme
Duty Control - Extreme
CPU Current Capability - 140%

CPU Voltage - Manual Mode
CPU Manual Voltage - 1.38
DRAM Voltage - 1.65 (depends om memory
VCCSA Voltage - Auto
VCCIO Voltage - 1.05
CPU PLL Voltage - 1.90
PCH Voltage - 1.05
CPU Spread Spectrum - Disabled

CPU Power Management
CPU Ratio - Auto
Enhanced Intel SpeedStep Technology - Enabled
Turbo Mode - Enabled
Turbo Ratio - Maximum Turbo Ratio settings in OS
Maximum Turbo Ratio settings in OS - 50

Turbo Mode Parameters
All Auto

Advanced/CPU Configuration
CPU Ratio - Auto
Intel Adaptive Thermal Monitor - Disabled
Active Processor Cores - All
Limit CPUID Maximum - Disabled
Execut Disable Bit - Enabled
Intel Virtualization Technology - Disabled
Enhanced Intel SpeedStep Technology - Enabled
Turbo Mode - Enabled
CPU C1E - Disabled
CPU C3 Report - Disabled
CPU C6 Report - Disabled


Mobo Asus P8P67PRO
2x2ГБ DDR3 Kingston Hyper X KHX2133C9AD3T1K2/4GX (PC17000, 2133МГц, CL9)

[wekktor]

very nice 1Day !, batch# ?

[coolhandluke41]

I also think that L042B076 it's a go for it!


My 1st L042B076

5.0Ghz with 1.424v not bad :P



But the 2nd one is the best:

1.424v set on bios ( vCore jumping from 1.416~1.432v )

hey stoned is your EPU disabled ?

[st0ned]

hey stoned is your EPU disabled ?

That's the overcurrent protection right ? I'm not sure, why ?

[1Day]

Nice result is it prime stable!

As you know I do not do stable.

If I can bench at those frequencies then that is all I ask from a CPU. Stable as in prime95 or what ever the current flavour of the month is has no relevance for my needs.

I do think it is important to those whom it matters to.

In many ways I sort of see it like a kind of benching but instead of points for scores it is how long at what frequency. So I respect those who practice stability testing but it is not what I am into.

[Viss]

5.7 for wprime 1024 is very nice What batch chips you have ?

[PytonOrm]

As you know I do not do stable.

If I can bench at those frequencies then that is all I ask from a CPU. Stable as in prime95 or what ever the current flavour of the month is has no relevance for my needs.

I do think it is important to those whom it matters to.

In many ways I sort of see it like a kind of benching but instead of points for scores it is how long at what frequency. So I respect those who practice stability testing but it is not what I am into.

Batch FTW ???? and what cooling u use ln2 not air i think... do u run any superpi 1M or 32M

[1Day]

Batch FTW ???? and what cooling u use ln2 not air i think... do u run any superpi 1M or 32M

I booted into OS at 5.7GHz on air. But to bench Wprime and Super Pi 32 I have used water. My husband bought me a SS yesterday so that is what I will use in the future.

Re Batch : L040B307

[bro20000]

I booted into OS at 5.7GHz on air. But to bench Wprime and Super Pi 32 I have used water. My husband bought me a SS yesterday so that is what I will use in the future.

Re Batch : L040B307

Nice same batch has mine! I will try for 3.7 to when my new hardware comes!

[jackbrennan2008]

I booted into OS at 5.7GHz on air. But to bench Wprime and Super Pi 32 I have used water. My husband bought me a SS yesterday so that is what I will use in the future.

Re Batch : L040B307

nice work. did you use a 56x multi or a lower multi and bclk?

[1Day]

nice work. did you use a 56x multi or a lower multi and bclk?

57x Multi. And to be brutally honest it was very little my work and all the CPU.



I got these on Friday.

My first one had a wall at 5.4GHz so

[PytonOrm]

1Day

Awesome work !!! nice only 4 pcs of 2600K thats nuts

[aussie-revhead]

1day - awesome cpu, is that the highest ever for a 2600K ?

st0ned - very nice , hit them for max clocks please.

Guys do we have a discussion here on what rams to get for these?

[1Day]

1day - awesome cpu, is that the highest ever for a 2600K ?

st0ned - very nice , hit them for max clocks please.

Guys do we have a discussion here on what rams to get for these?

No there are six others that have clocked higher. Not sure if they clocked with HT on and all cores enabled like I do. But higher they have clocked. I bench so I am not really going to get any HWBOT points for CPU-z with a Sandybridge. Not when 8GHz plus is what you have to beat.

Ram is a difficult one. I have had amazing results (better than expected) with some Giel Evo Two sticks I bought for the P55 boards last year. 2000MHz Cas6 - 9 - 6 doing 2133 at Cas 6 with ease. The only discussion I saw was working out why Hypers are not clocking on the SB boards. But with my GA-P57A-UD7 board I have not had any hassle as you can see with Hypers. I wonder if it is board related. You know how the bios sets the latencies of the ram. But I have no real idea.

[aussie-revhead]

I meant is that the highest multi for a 2600K.

The faster ones on hwbot are not far ahead of yours, good work. Only one of those 6 is on 57x multi too.

http://www.hwbot.org/searchResults.d...peId=&offset=0

[Sam_oslo]

Good job 1Day, keep doing what you do best

[LagunaX]

Running on air cooling Venomous X 2 fans.
i7-2600k Batch L041C108.
Asus P8P67 motherboard.
5ghz LinX takes 1.4-1.41v to be stable but hits 89C!

So for 24/7 use I'm gonna stick to 4.9ghz 1.36v set in bios:

[aussie-revhead]

Nice Laguna, try benching at higher clocks without LinX torture? It would be good to see its highest possible multi.

[Falkentyne]

Yeah my venemous-X with just one fan gets up to 90C in small FFT prime, with 5 ghz and 1.45v load going through the thing.
And TRUE black with Ven-X mount fares even worse, even though the mount is so secure with the TRUE that it doesn't swivel one bit...(the Ven-X swivels but temps are lower).

Even a 190cfm Delta won't help, because it reaches 80C within 5 seconds...