***Official***Z68X/P67A-UD7 Club/Discussion/Info**

[Polypenko]

At the moment Vcore is set to 1.265v with LLC Level 1. Ram is set to 1866 with 1.54v otherwise everything else if left on auto. I'll test it again tomorrow with Auto settings and see how DES2 responds to that. I'm assuming it's due to the Beta bios i'm using (F7A) or as you put it, it's not entirely compatible with P67 yet.

Tried 4500mhz - ram 1867mhz cpu voltage 1.265V llc level 1 - NO GO.

change to 4400mhz ram 1867 same as above - pc started later changed
the ram to 2133mhz, so far pc did not yet crash.

at this moment I'm not trying DES since I fear my W7 will crash again.

so eventhough we have the same mb and processor, the Ram modules
seem to be very sensitive.

[stasio]

Run Super PI 32M.

[Polypenko]

this is de Superpi 30m run.

[stasio]

This is 1M ,scroll at bottom is 32M.

[Polypenko]

this is de 32m run.

cpu 4400mhz cpu 1.265 V - LLC Level 1
ram 2133mhz 1.66 V profile 1

4400mhz just crashed slightly increased the cpu voltage to 1.285 mhz.

[stasio]

That's good one.
Try with BIOS F7d,should be better.

[Polypenko]

Just installed F7D

left cpu at 4400mhz cpu voltage 1.285 v

ram 2133 mhz 1.66 v


should I lower te cpu voltage to 1.265 v or set it to auto in the bios?

[stasio]

Up to 4.6 GHz can be all on Auto,except memory setting.
Try 4.6.
My 4.6GHz on Auto,except memory:

[maxxx]

Guys, when coming from a cold boot, does your board reboot twice before going to the OS? My board would get stuck on C1 then reboot, then its the only time it would continue the boot process. Even on stock settings.

[Polypenko]

changed the settings to auto in the bios / ram profile 1 = 1.66v

and W7 booted up nicely.

Than I tried to use DES, and my PC CRASHED

this board does not like DES at higher settings, perhaps it make's
sence, since this programme tries to reduce voltage's etc. but we are
forcing the mb to start at an overclock of 35% at higher setting's than
standard?

I will e-mail GB in the Netherlands and ask them to relay this info
to Taiwan.

[stasio]

Guys, when coming from a cold boot, does your board reboot twice before going to the OS? My board would get stuck on C1 then reboot, then its the only time it would continue the boot process. Even on stock settings.

You are lucky (only twice),my reboot 5,6,7-8 times with freeze on Logo screen,must off PSU,then again twice before I can go in the BIOS again.

changed the settings to auto in the bios / ram profile 1 = 1.66v

and W7 booted up nicely.

Than I tried to use DES, and my PC CRASHED

this board does not like DES at higher settings, perhaps it make's
sence, since this programme tries to reduce voltage's etc. but we are
forcing the mb to start at an overclock of 35% at higher setting's than
standard?

I will e-mail GB in the Netherlands and ask them to relay this info
to Taiwan.

Don't use any additional software like DES,at this stage.Make your board stable first.

[1Day]

You are lucky (only twice),my reboot 5,6,7-8 times with freeze on Logo screen,must off PSU,then again twice before I can go in the BIOS again.

Stasio since I flashed my bios to the F7d that has stopped for me.

[Polypenko]

Stasio / Oc nub & Jackbrennan tks. for your help so far.

Running at 4600mhz Ram 2133mhz Bios all on auto.

Max Cpu Voltage 1.332 v

Insane easy overclock of 35 percent.

[OC Nub]

Thought I would try 8gb of ram, not matching kits, proabably the same other than heat spreaders.

[sin0822]

that is pretty nice.

[dinos22]

hey peeps

i got a few bios updates for UD4/5/7 which should sort this S3 multiplier dropping to 35x after exiting sleep mode

give it a crack

I tested UD7, it works, just enable S3 in bios

http://filefactory.com/file/b5167da/n/Desktop.zip

[TheHardCase]

hey peeps

i got a few bios updates for UD4/5/7 which should sort this S3 multiplier dropping to 35x after exiting sleep mode

give it a crack

i will test later today

http://filefactory.com/file/b5167da/n/Desktop.zip

Thanks bro for all the help...

[dinos22]

hmm seems new bios has more than just S3 fix, my bclock wall is no longer 104.3, i am booting past it now eeeek > up to 107 now heheh

[C-N]

hmm seems new bios has more than just S3 fix, my bclock wall is no longer 104.3, i am booting past it now eeeek > up to 107 now heheh

Sounds good my ud5 gets in windows at 105.4 but locks up after a while. 104.4 is all i can run stable.

[dinos22]

this one booted up at 105 and rest was through windows.

bclock isnt really a bit deal with you have unlocked multi but it can be useful for RAM clocks i guess heh

[stasio]

hmm seems new bios has more than just S3 fix, my bclock wall is no longer 104.3, i am booting past it now eeeek > up to 107 now heheh

Yeah and I flashed with Q-Flash with no problem.

[1Day]

Thanks Dinos will give it a try when I get up before work tomorrow. Um later this morning I guess that should be.

[nijel]

hey peeps

i got a few bios updates for UD4/5/7 which should sort this S3 multiplier dropping to 35x after exiting sleep mode

give it a crack

I tested UD7, it works, just enable S3 in bios

http://filefactory.com/file/b5167da/n/Desktop.zip

It doesn't fix the problem completely for me. My turbo MPs are set to 45 for all 4 cores and after wake up the turbo behaves like the default turbo function, like the mp are set 45,44,43,42 for the cores. At 100% load CPU runs at 4.2 and increases to 4.5 with the load going down. That's exactly how the default turbo function works.
Not 100% fixed from my point of view.

[skeyo]

I found sweet sport for 24/7 :P

[OC Nub]

@skeyo Congrats!! Nice chip.


First real try at raising bclk, just a little. Also seeing how these Mushkin Radioactive's oc on the UD7. Default is 1600mhz 6-8-6-24, they seem to do pretty good with this board.