Super Pi 32M Low Clock Challenge

[dinos22]

is that from one of your warmup sessions jody

New challenge..........who will grow the cwaziest mustache here ... Jody's in the lead

[3oh6]

What voltage did you use for the memory?
Very good score there

1.849v perhaps

what he said ^
in the full size screen shot i have the voltages listed. was likely 1.88v set or something like that. the kit goes up to 1054MHz 6-6-5 with the same volts.

is that from one of your warmup sessions jody

definitely just a warm up while i wait for an RMA on my CPU because i haven't had time to send it out because i have too many reviews on the go ever since i put a list of contacts in my XS signature and hardware started pouring in.

but i will definitely be trying for better if i can find a CPU with better uncore and a kit of memory that can do the same clocks because i don't want to use this kit anymore because it is for memory reviews from my huge list of contacts.

you know how it is

[dinos22]

sweet cant wait to see what the new silicone brings to this thread

[George_o/c]

definitely just a warm up while i wait for an RMA on my CPU because i haven't had time to send it out because i have too many reviews on the go ever since i put a list of contacts in my XS signature and hardware started pouring in.

but i will definitely be trying for better if i can find a CPU with better uncore and a kit of memory that can do the same clocks because i don't want to use this kit anymore because it is for memory reviews from my huge list of contacts.

Welcome back

[George_o/c]

P55 32M lovin'
Dedicated to my good friend Stephan

[Hyperhorn]

*Update*

@George: Oh, that´s a nice way to avoid 2:10. The dedication is much appreciated!

[0Ro!]

first touch with LGA 1366 and X58 on h2o

8.XX time zone

3930.8.....0Ro!.....8.59.953....196,5x20....982,6. ...7-8-7-21...2/10..X58



next time I will push the uncore and RAM a little higher

[Hyperhorn]

*Update*

[Splave]

oro why 2t?

[0Ro!]

because i wanted first to test the RAMs with the voltage of 1,65V how they perform ... nextime will try on SS with more voltages and 1T on RAMs

[Mafio]

may i join?

8.** zone

Config:

• i7-920 // SS 1.2 HP
• EVGA Classified E760 // bios E76044
• KHX 2k cas8 // silverstone 80mm
• 6200 LE PCI-E 256 MB
• P&C 1200
• 2003 Sever TW // fully tweaked + copy waza

super-pi 32M // 8.59.844 // 950 @ 3833.3 MHz // KHX 2k cas8 @ 912 MHz 6-6-4-18

3833.3.....Mafio.....8.59.844....182.5x21....912,7 .....6-6-4-18...2/10..X58

[subaruwrc]

may i join?

8.** zone

Config:

• i7-920 // SS 1.2 HP
• EVGA Classified E760 // bios E76044
• KHX 2k cas8 // silverstone 80mm
• 6200 LE PCI-E 256 MB
• P&C 1200
• 2003 Sever TW // fully tweaked + copy waza

super-pi 32M // 8.59.844 // 950 @ 3833.3 MHz // KHX 2k cas8 @ 912 MHz 6-6-4-18

3833.3.....Mafio.....8.59.844....182.5x21....912,7 .....6-6-4-18...2/10..X58

now that is something !
congrats

im struggling to get sub 9 min at 3914mhz... only on air but cannot tigthen my ram more at 2060 than 7-7-5-19
and it always crashes at 3933mhz XD

[Calathea]

3825.1......Calathea............9.59.109....17x225 ......900MHz......8-8-7-10.....2/8..H55
I hope I got the right amount of dots



Will charge for 8.xx, but I'm having a hard time keeping nice efficiency with higher clocks. Some better sticks would help for sure.

[Mafio]

8.xx

3832.3......Mafio.............8.59.985....17x225.4 ......901.7MHz......6-6-4-18.....2/8..X58

[Hondacity]

those are crazy subtimings...nice one mafio...supertalents ftFW

[Mafio]

yes, STT rulez...especially when i paid only 200 € for them (including shipping cost and customs fee)

i see a lot of guys using tRRD and tRTP both at 1 but i can't find the way to run them that tight.
CPU-tweaker always shows 4 and 2...
force them to 1 in windows doesn't give any performance improvement.

[Hondacity]

yeah tRRD and tRTP are kinda hard on the STT compared to the gtx2000c7s.

i do them inside the bios though...my test is the xp bootup ..if it doesn't boot..they're no good ..lol

[Mafio]

the problem is that when i set them to 1 in bios CPU-Tweaker ALWAYS show me tRRD 4 and tRTP 2.
force them in windows to 1 doesn't make my super-pi faster...my guess is: all of these guys that use tRRD 1 and tRTP 1 force them to 1 in windows or boot directly with 1 - 1 ?
if they can boot 1 - 1 would be good to know how they did it because i can't find the way to do it
if i set 1 - 1 windows boot normally but when i check with CPU-Tweaker i see tRRD 4 and tRTP 2...

[cheapseats]

the problem is that when i set them to 1 in bios CPU-Tweaker ALWAYS show me tRRD 4 and tRTP 2.
force them in windows to 1 doesn't make my super-pi faster...my guess is: all of these guys that use tRRD 1 and tRTP 1 force them to 1 in windows or boot directly with 1 - 1 ?
if they can boot 1 - 1 would be good to know how they did it because i can't find the way to do it
if i set 1 - 1 windows boot normally but when i check with CPU-Tweaker i see tRRD 4 and tRTP 2...

think that's the correct result Mafio .. can just leave at tRRD 4, tRTP 2
i don't find any faster at 1 either (cputweaker set only), although i still do it on mine when i set tREF

can you tighten rtl on 226bclk cl6 setting ?
20x uncore is 60-62-63/64, 21x should only be ~ +3 per channnel eg 63-65-66/67.

any more runs coming ?

[Mafio]

think that's the correct result Mafio .. can just leave at tRRD 4, tRTP 2
i don't find any faster at 1 either (cputweaker set only), although i still do it on mine when i set tREF

can you tighten rtl on 226bclk cl6 setting ?
20x uncore is 60-62-63/64, 21x should only be ~ +3 per channnel eg 63-65-66/67.

any more runs coming ?

good to know that i'm not the only one that can't run 1 - 1
no way to use tighter RTLs, what you see are the tightest values i can set
the best i can do is 66-68-70, with only one less i lose 1 stick or 32M gives errors.

BTW, yes, i've something more
same setup as before except for RAM, this time i used the good old trusty HyperX 2000 cas8

10.xx

3086.1......Mafio.............10.59.610....13x237. 4......950MHz......6-6-5-18.....2/8..X58

[Aerou]

HyperX Hypers FTW I still cherish mine.

[youngpro]

wow mafio nice clocks on the rams there!

damn astridies i will say it again, that is a very fast run,

i have been playing over the last few days with UD3R and R3E... Rampage 3 Extreme is so fast and the best thing is, its so EASY to make it go this fast, giga is more effort but I think it is possible the UD9 with bloomsfield microcode bios is faster than r3e,

I am using B1 cpu because it does not need bloomsfield microcode to be very fast, but at the same time, i do think that mrc bios does work wonder on UD9 and low 6-6-5 style ram clocks, my original runs were 36.5 with only 4000 MHz, I think by knocking to 4007 they should be in 35.7 range or so.. same with the R3E..

either for ease of fast 32m, r3e is your board, and for price, i think ud3r is very nice..

[Mafio]

scary fast run pro
i need to try 32M with one of these GB boards, they look a lot faster than classified that i'm using now.

[Hyperhorn]

*Update*

... thinking about Sandy Bridge color scheme ...

[dinos22]