UnOfficial EVGA X58 Classified Owners Thread

[rusty]

OC_NUB can I see your template for 4.5ghz ?

[OC Nub]

This has worked pretty good for me.

Frequency Control
CPU Clock Ratio ( 21X )
CPU Host Frequency (Mhz) ( 215 )
MCH Strap ( 1333 )
CPU Uncore Frequency (Mhz) (x17)
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) ( 105 )


Memory Feature
Memory Control Setting (Enabled )
Memory Frequency ( 2:8 )
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way )
Memory Low Gap ( Auto )
tCL Setting ( 7 )
tRCD Setting ( 7 )
tRP Setting ( 7 )
tRAS Setting ( 20 )
tRFC Setting ( 60 )
Command Rate ( 1T )


Voltage Control
EVGA VDroop Control ( With VDroop )
CPU VCore (1.4375 ht disabled) {1.4625-1.475 ht enabled, cant remember exactly with ht, load vcore is 1.411v)
CPU VTT Voltage (+75)
CPU PLL VCore (1.50)
IOH PLL VCore (1.50)
QPI PLL VCore (1.175)
DIMM Voltage (1.60)
DIMM DQ Vref ( +0 )
IOH VCore (1.175)
IOH/ICH I/O (1.500v)
ICH VCore (1.050)
VTT PWM Frequency ( 250 )
CPU PWM Frequency ( 800 )
CPU impedance - (auto)
QPI signal comp (auto)


CPU Feature
Intel SpeedStep ( Disabled )
Turbo Mode Function ( Enabled )
CxE Function ( Disabled )
Execute Disable Bit ( Disabled )
Virtualization Technology ( disabled)
Intel HT Technology ( Enabled )
Active Processor Cores ( All )
QPI Control Settings ( Enabled )
QPI Link Fast Mode ( Enabled )
QPI Frequency Selection ( 4.800 GT/s)

[Bullet92]

CPU Uncore Frequency (Mhz) ( 2x memory frequency )
Memory Control Settings ( Manual - use 2:10 )
Memory Low Gap ( Auto )
CPU PLL VCore ( 1.8 )
QPI PLL VCore ( 1.200)
IOH VCore ( 1.200 )
IOH/ICH I/O Voltage ( 1.500 )
ICH VCore ( 1.100 )
CPU PWM Frequency ( 800KHz )
CPU Impedance (Auto)
QPI Signal Comp (Auto)

Try these settings.

[rusty]

OC_NUB do run this setup 24/7 at 4.6 ? at these volts ?

[OC Nub]

I run it 215x21/4.5ghz with these settings 24/7. The chip was in my last motherboard running 4.5 for probably 6 months or so.

[kup]

Same template as above, 230MHz BCLK 3D stable so far (Black Ops for HOOOOOURS! ).

[KILLER_K]

Try these settings.

Tried those settings and it just freezes at the windows logo each time.

[OC Nub]

Same template as above, 230MHz BCLK 3D stable so far (Black Ops for HOOOOOURS! ).

Congrats, Great bclk for gaming lol. These boards are pretty sweet. Looks like the 218bclk wall is far behind you now.

[radaja]

well i finally got above 217bclk
thanks zsamz,mafio,OC nub and kup for all your guy's help

vcore is way high ,needed to rule cpu(vcore)out 100%

[OC Nub]

Nice radaja.

Will you switch back to Giga now or keep testing the E760?

[Mafio]

good work radaja

[Bullet92]

Tried those settings and it just freezes at the windows logo each time.

What about more vCore?

[radaja]

Nice radaja.

Will you switch back to Giga now or keep testing the E760?

thanks,i will test this one for a while and then make a decision.i know i couldnt do 226 bclk stable on the the UD5 but could on my last UD3R,i could boot and run the quick superpi 1m at 230 with the UD5.but it looks like with this E760 230 stable might be possible for sure

good work radaja

thanks

[Sam_oslo]

I didn't read all good job you guys are doing for raising the BCLK-wall. Could somebody give a quieck summery on important adjestments.?

I'm trying to pick some idea to use on SR-2. Diffeent BIOS and chipset may make a big different though, but it's worth to get some ideas and trying.

[KILLER_K]

What about more vCore?

Went up on the vcore as high as i should have needed but nothing helped. It is probably a setting i am over looking though. I will keep trying.

[zsamz_]

guys cpu n qpi signal less = usin less volts
some boards might be ok for auto

i was gonna post my 231blk x21 template but i need to tweek it
as soon as i get my psu back ....
ti'll then

[KILLER_K]

guys cpu n qpi signal less = usin less volts
some boards might be ok for auto

i was gonna post my 231blk x21 template but i need to tweek it
as soon as i get my psu back ....
ti'll then

Post it and give me some ideas. I need something else to compare mine to now.

[rusty]

I think cpu & qpi signal less or auto is different for everyone.

[emertX]

Do you guys know, if a Q3QR runs on a Classified withou a mod?

[radaja]

i finally got 230bclk stable,thanks to zsamz
now i just need to up the multi and lower some timings
and i will be in heaven



heres my settings,i now need to tweak some voltages down
but it makes a good starting point for others.

Frequency Control
CPU Clock Ratio ( 15X )
CPU Host Frequency (Mhz) (  231  )
MCH Strap ( Auto)
CPU Uncore Frequency (Mhz) (3910MHz x17) 
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) ( 113 )


Memory Feature
Memory Control Setting (Enabled )
Memory Frequency ( 2:8 )
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way )
Memory Low Gap ( Auto )
tCL Setting  ( 8 )
tRCD Setting ( 8 )
tRP Setting  ( 8 )
tRAS Setting ( 24 )
tRFC Setting ( 88 )
Command Rate ( 1T )


Voltage Control
EVGA VDroop Control ( Without VDroop )
CPU VCore       (1.32500) 
CPU VTT Voltage (+150) 
CPU PLL VCore   (1.8)
IOH PLL VCore   (1.8)
QPI PLL VCore   (1.35)
DIMM Voltage    (1.63)
DIMM DQ Vref    ( +0 )
IOH VCore       (1.35)
IOH/ICH I/O     (1.65)
ICH VCore       (1.12)
VTT PWM Frequency ( 250 )
CPU PWM Frequency ( 800 )
CPU impedance - (less)
QPI signal comp (less)


CPU Feature
Intel SpeedStep ( Disabled )
Turbo Mode Function ( disabled )
CxE Function ( Disabled )
Execute Disable Bit ( Disabled )
Virtualization Technology ( Enabled ) 
Intel HT Technology ( Enabled )
Active Processor Cores ( All )
QPI Control Settings ( Enabled )
QPI Link Fast Mode ( Enabled )
QPI Frequency Selection ( 4.800 GT/s)

[OC Nub]

WOW Great job radaja.

[kup]

Well done dude!

EDIT: Was PCIE @ 113 essential for you?

[radaja]

WOW Great job radaja.

thanks,couldnt have done it with out your help

Well done dude!

EDIT: Was PCIE @ 113 essential for you?

thanks for your help in understanding the board
well i havent tried lower yet,but now that i have a solid 230
i will test individual voltages and setting to see whats needed
and whats excessive.will post my findings and leave an updated template

[zsamz_]

i finally got 230bclk stable,thanks to zsamz
now i just need to up the multi and lower some timings
and i will be in heaven

congrats

i got my psu back from rma i'm right behing ya

kup: i dont have to put template up now

[radaja]

finally a decent memory score,at least for me
still working on lowering stuff(volts)but soon i will have
this MB nailed down and make it do what i want