Unofficial Gigabyte GA-X58A-UD9 Thread

[dMITIj]

okay thx.

this is my settings for 3485Mhz:

MB Intelligent Tweaker(M.I.T.)

CPU Clock Ratio............................: 21
CPU Frequency .....(Mhz)...................:3.485
Advanced CPU Features [Press Enter]
Intel(R) Turbo Boost Tech.................:[Disabled]
CPU Cores Enabled...........................:[All]
CPU Multi Threading.........................:[Enabled]
CPU Enhanced Halt (C1E)..................:[Disabled]
C3/C6/C7 State Support...................:[Disabled]
CPU Thermal Monitor........................:[Disabled]
CPU EIST Function...........................:[Disabled]
Bi-Directional PROCHOT.....................:[Enabled]


QPI Clock Ratio*...............................:auto
QPI Link Speed* ...............................(Ghz):6
Uncore Clock Ratio.............................:x21
Uncore Frequency..............................(Mhz):3500

Isochronous Support.........................:[Enabled]
Virtualization Technology...................:[Enabled]

>>>>>Standard Clock Control
Base Clock (BCLK) Control*.................:[Enabled]
BCLK Frequency (Mhz)*......................:166
Extreme Memory Profile (X.M.P.)............:[Disabled]
System Memory Multiplier (SPD).............:[10.0]
"Memory Frequency (Mhz) 1066 1667"
PCI Exxpress Frequency (Mhz)...............:[100]
>>>>>Advanced Clock Control
CPU Clock Drive (mV).......................:[800]
PCI Express Clock Drive (mV)..............:[900]
CPU Clock Skew (ps)........................:0
IOH Clock Skew (ps)........................:0

Advanced Memory Settings [Press Enter}
Extreme Memory Profile (X.M.P.)............:[Disable]
System Memory Multiplier (SPD).............:[10.0]
"Memory Frequency (Mhz) 1066 1667"
Performance Enhance........................:[Standart]
DRAM Timing Selectable (sPD) ..............:[Expert]
Channel Interleaving.......................:6 [auto]
Rank Interleaving..........................:4 [auto]

>>>>>Channel A Standard Timing Control
Cas Latency Time.............................:9
tRCD.........................................:9
tRP..........................................:9
tRAS.........................................:27
>>>>>Channel A Advanced Timing Control
tRC..........................................:36
tRRD ........................................:4[Auto]
tWTR ........................................:4[Auto]
tWR..........................................:8[Auto]
tWTP.........................................:19[Auto]
tWL..........................................:7[Auto]
tRFC.........................................:60[Auto]
tRTP.........................................:4[Auto]
tFAW.........................................:16[Auto]
Command Rate (CMD) ..........................:1
>>>>>Channel A Misc Timing Control
B2B CAS Delay................................:-[Auto]
Round Trip Latency...........................:64[Auto]

Channel A Turnaround Setting [Press Enter]
>>>>> Channel A Reads Followed By Reads
Different DIMMs..............................: [Auto]
Different Ranks..............................: [Auto]
On The Same Rank.............................: [Auto]
>>>>> Channel A Writes Followed By Writes
Different DIMMs..............................: [Auto]
Different Ranks..............................: [Auto]
On The Same Rank.............................:[Auto]


Advanced Voltage Control [Press Enter]
>>>>CPU Voltages
LoadLine Calibration.........................:[Level 2]
CPU Vcore....................................:1.22500v
QPI/VTT Voltage..............................:1.175v
CPU PLL......................................:1.80v [Auto]
>>>>>MCH/ICH Voltrage
PCIE.........................................:1.50 v[Auto]
QPI PLL......................................:1.10v[Auto]
IOH Core.....................................:1.10v[Auto]
ICH I/O......................................:1.50v[Auto]
ICH Core.....................................:1.10v[Auto]
>>>>>Dram
DRAM Voltage.................................:[1.640v]
DRAM Termination.............................:0.750v[Auto]
Ch-A Data Vref...............................:0.750v[Auto]
Ch-B Data Vref...............................:0.750v[Auto]
Ch-C Data VRef...............................:0.750v[Auto]
Ch-A Address Vref............................:0.750v[Auto]
Ch-B Address Vref............................:0.750v[Auto]
Ch-C Address VRef............................:0.750v[Auto]

[dinos22]

what bios are you using?

[dMITIj]

the newst F4

[dinos22]

hmm ok

pull the plug and battery clear cmos >

plug PSU in, keyboard only, one stick of ram in the white slot furthest away from CPU and GPU that's it

bios load optimised defaults and then go back into bios and set multi to 21, disable turbo, set bclock to 175 and do not touch any other options at all other than vcore 1.3, vtt 1.35, vdimm 1.66

leave the rest of options with whatever bios gives you

try 185 and 200 as well


if it doesnt work pull the board out of the case, take HS off, flex the board a bit, pull CPU and put it back in after inspecting the CPU socket pins carefully for any damaged pins again (maybe take a macro shot and look at it on the PC) and after reinstalling cpu plug bare essentials outside case and only leave the CPU HS on top of CPU without mounting on the board....just hold it down with minimal pressure and fire up the rig, change the settings suggested above again and see if it does it.

If that doesnt work you will need to check all the parts individually to see what's playing up exactly.

[dMITIj]

hmm ok

pull the plug and battery clear cmos >

plug PSU in, keyboard only, one stick of ram in the white slot furthest away from CPU and GPU that's it

bios load optimised defaults and then go back into bios and set multi to 21, disable turbo, set bclock to 175 and do not touch any other options at all other than vcore 1.3, vtt 1.35, vdimm 1.66

leave the rest of options with whatever bios gives you

try 185 and 200 as well

Done, but that didtent do anything different, still the same shjiiit will look in to the other thing in a min. ore so

[dMITIj]

hmm ok

pull the plug and battery clear cmos >

plug PSU in, keyboard only, one stick of ram in the white slot furthest away from CPU and GPU that's it

bios load optimised defaults and then go back into bios and set multi to 21, disable turbo, set bclock to 175 and do not touch any other options at all other than vcore 1.3, vtt 1.35, vdimm 1.66

leave the rest of options with whatever bios gives you

try 185 and 200 as well


if it doesnt work pull the board out of the case, take HS off, flex the board a bit, pull CPU and put it back in after inspecting the CPU socket pins carefully for any damaged pins again (maybe take a macro shot and look at it on the PC) and after reinstalling cpu plug bare essentials outside case and only leave the CPU HS on top of CPU without mounting on the board....just hold it down with minimal pressure and fire up the rig, change the settings suggested above again and see if it does it.

If that doesnt work you will need to check all the parts individually to see what's playing up exactly.

omfg!! done every single thing now............. danm!!


im up and running 21x200BCLK with the settings above DD
FULL SIZE: http://peecee.dk/upload/view/265332/full


Thanks for the help so far dino22

[dinos22]

no probrem

so what was it then exactly

[dMITIj]

no probrem

so what was it then exactly

Hehe, i haven't put it all together yet but i will later today, but when i pulled it all out of the case i pulled the battery out to for an houre ore so and once againe cleard cmos and i think thats the reason but ill know when it all is back in the case, later today


i have to say that i didt buy this mb as an secondhand at the shop i normaly do my shopping in, and got it like 200$ cheaper than the "real" price, so maby the other guy who have had this mb didt somthing and couldent get it back on track, but it is now

[dinos22]

LMAO i hope it wasnt this guy

http://www.youtube.com/watch?v=huGl2hfzL90

[dMITIj]

LMAO i hope it wasnt this guy

http://www.youtube.com/watch?v=huGl2hfzL90

hehe nope, he still got his
after the wash he have put it in the oven at 70 degrees for 4 hours and have fired it up againe and everything works as before hehe

[dMITIj]

okay back in the case, i think it were the BIOS that needed the full pull battery out/clear cmos stuff, because no problems for now

[hicookie]

Update GO OC special version for UD9

http://rapidshare.com/files/419503665/GOOCUD9.W01

feature same as UD7 GO OC version
1. Vcore 1.0v - 2.1v
2. OC lean Mode
3. Extreme Clock
4. Extreme Temp

http://gigabytedaily.blogspot.com/20...s-release.html

[nacho_arroyo]

Update GO OC special version for UD9

http://rapidshare.com/files/419503665/GOOCUD9.W01

feature same as UD7 GO OC version
1. Vcore 1.0v - 2.1v
2. OC lean Mode
3. Extreme Clock
4. Extreme Temp

http://gigabytedaily.blogspot.com/20...s-release.html

The link is down, please add new one

[boldenc]

The link is down, please add new one

reuploaded: http://www.4shared.com/file/cHoXXtR2/GOOCUD9.html

[nacho_arroyo]

reuploaded: http://www.4shared.com/file/cHoXXtR2/GOOCUD9.html

tks very much

[crucial33]

Im currently examining this board closely, although posts seem few and far between. Im looking to actually mount it in a case, can anyone tell me what cases fit except the ones recommended on gigabytes site? Which case are you using?I currently have CM cosmos s, but looking at pictures of the board, i dont think its going to fit. What are general opinions of this board of those that own one, it sure looks nice, but is it better than it looks

[dMITIj]

okay back on UD9 again, the problém were the reset button :-)

but now i can't OC at all, if i do so, my SSD will "fail" any idea?

[stasio]

GA-X58A-UD9 - F5f

-Improve SSD compatibility
- 09.Nov 10

[[200]]

Thanks stasio, i've updated the front page.

I know i've missed a couple of bios revisions but oh well...

[crucial33]

Can anyone give a list of cases (other than the ones on gigabytes site) that will fit this case? Anyone know if a seven PCI slot case (ie CM cosmos s ) will fit this board?. Obvously 4 cards in a 7 pci slot case is a no no, but what about running dual card SLI for instance, can i get it to work like that until i get a 10 slot case? Help appreciated, i want to buy this board, but must be sure i can fit it in my case.

[zalbard]

Can anyone give a list of cases (other than the ones on gigabytes site) that will fit this case? Anyone know if a seven PCI slot case (ie CM cosmos s ) will fit this board?. Obvously 4 cards in a 7 pci slot case is a no no, but what about running dual card SLI for instance, can i get it to work like that until i get a 10 slot case? Help appreciated, i want to buy this board, but must be sure i can fit it in my case.

Not enough space I am afraid, the board will hit the PSU.

[kintaro]

is there any bios more Bclk friendly for the 920?
on rex 3 this chip can do up to 260 so is mobo matter.

[sin0822]

I would think GOOC bios would be much better, have you tried that?

[[200]]

I used F4B for my runs. Reached 262 bclks.

[kintaro]

I would think GOOC bios would be much better, have you tried that?

already try. 240max whatever settings

I used F4B for my runs. Reached 262 bclks.

Thanks. I'll try this version.