DFI Lanparty UT P45-T2RS Banter starts here!!!

[fatguy1992]

Could someone tell me what the max Vcore is on the UT P45-T2RS?

Thanks

[SOXX]

In the Bios the max is 1,6V, i dont know if the special add works with this Vcore setting, when it works you can give more Vcore than 1,6V over the special add option.

[fatguy1992]

Thanks

How much more?

Cause 1.6v isn't enough for me anymore

[SOXX]

The voltage go up to 1,6V. The Special Add go up to 130%. When the Special Add work with this high Vcore you can give your CPU 2.08Vcore .

1,6 : 100 = 0.016 x 130 = 2,08V

I dont test it with my good Q9550

[fatguy1992]

That sounds awesome, I might look into this board more, the only thing is I can't seem to find one in Australia or on Ebay

[SOXX]

I think this Shop ships arraund the world -> http://www.motherboardpro.com/

[fatguy1992]

Thanks

Edit: I just looked in the checkout and it only says Canada and USA

[DJSUB]

i killed one of my most highclocker E8400 last feb.
right now I'm having problem with my DFI Lanparty UT P45 T3RS.
i couldn't enter bios in any way.
i already did all the methods below but the result is always the same.

clearcmos & remove battery for 8hrs. no power connected to the mainboard.
replace psu & video card, proc & cpu cooler.
the only thing i've never did is to replace the memory.
before my e8400 died i already did some occt 2hrs mix stability testing with that board & my 3gb kit team xtreem ddr3 1866 in dual channel mode.
it run stable with my settings.
then after my e8400 died, i tried to borrow some procs on my cousin. E5200 & E2140
E5200 run's fine on my mobo that time, but when i tried to put e2140 on my mobo i started experiencing the bios problem.
i can boot to windows without any problem.

i already did flashing the board on windows & dos mode several times & the result are always the same. can't enter bios.
the last test i did is memtest for dos. 3 rounds of standard test without any error.

please let me know if you have any solution to this problem.

thanks in advance

[03hdfatboy]

I love this Motherboard!

[Kean]

Any one of you can run with FSB, lets say... 640-650MHz?
DK plus is really great, but I don't saw any superb scores on UT

[95blackz26]

anyone get this thing higher than 512. as high as i can go is 512x8 and then there seems to be a wall that wont let the board even post.

i tried using x7 and it wouldnt go higher either. this is completely stable in OCCT

i plan on watercooling this board in the near future just gotta pick out the components

whats the max people have gotten this on air.

the CPU-Z validation for 512 in in my sig
this is the 510 screenshot but i did it for 512 too

[kitfit1]

Any one of you can run with FSB, lets say... 640-650MHz?
DK plus is really great, but I don't saw any superb scores on UT

I very much doubt that anyone can run that fsb 24/7 stable. Suicide shot yes, but not 24/7. Mine can run 563fsb 24/7 stable with 4x1024 sticks of ram, as in my sig. Can't be bothered to try for a pointless suicide shot though.

[Blackwhite]

Ok guys I have problem with my Mobo.My vdrop is quite high 0.057v - vdrop is disable in BIOS.
I have very nice chip Q822A462 and I can't reach 4.5 GHz with 1.375v set in BIOS stable.
My settings:
450x10
1.375v BIOS (1.328v OS)
VTT 1.2v
NB 1.2v
GTL 0.625 each
DDR/CPU 1:1 (tried 5:6)
DDR 2.19v
PLL 1.55v
I notice when I set NB higher than 1.24v I have nothin on screen and I can't boot to windows.


Even 4.8 GHz with 1.475 I can boot to windows.
I can do 4 GHz with 1.18v easy but nothing more stable.
Maybe I shoul set additional VID in BIOS or something like that - anybody can help please.

My Mobo is DFI P45 UT T2RS ofcourse.

[kamieldehond]

I bought this board and im interested in the best bios for this board

[kamieldehond]

ok just installed the newest bios (not beta). I like the board already, without any overclocking done
anyway 1 small drawback tough. I put my vga in the second slot as im running a ram cooler and therefor the vga cant fit in the first slot. I noticed that my vga was running at 8x instead on 16x. Is it possible to run 16x in the second slot?

i hope we can get this thread running again Anyway ill probably will post my overclocking tries in here

[kamieldehond]

played a little with the board as i didnt had much time. It clockes my e8500 a lot better then my maximus II formula, as it needs less voltage, but i couldnt get my ram to the desired frequentie quick. Im running 4x1gb d9gmh and i got them to 1200mhz pretty easy on the maxiums but i couldnt get the DFI stable at 1100mhz (only thing i tried).

Anybody has some tips to get the ram clocking on this board?

Atm im not at my pc so i cant post a bios rundown, ill do this when im back at my pc

[DashTrash]

kamieldehond, I just picked this board up a couple days ago. My work schedule is not good during the summer, so I probably won't have much tweak time until late August, but I'm also interested in what this board can do. I had the p35-t2r watercooled with a q6600 and waterblocks on the mosfets and nb. I did pretty good with 4x1gb sticks. If I remember correctly, I had crucial 8500 tracers @ 450fsb, 1200ram 2.3v. I would hope this board can do that also.

I am curious how this board does with q9550/q9650s. Everybody claims the p45-ud3p is great with quads (500+ fsb), but I haven't heard how this board does. Anyone had any luck? Also curious how it does with the new low voltage 2gb ram modules like the ocz blade series.

[kamieldehond]

getting some wierd stuff from this mobo. the error codes i get:
75 when it just hangs in bios
7F when loaded the bios defaults are loaded
FF when its booted in to windows (dont know if this is normal)

anyway when i look up the last 2 error codes it says i should rma the board, or do i just not read the error code list right?

*edit

googled a little more and found out that FF is normal when you boot to windows so no problem there

[kamieldehond]

>CPU Feature:

Thermal Management Control.......... - Enabled
PPM(EIST) Mode...................... - Disabled
Limit CPUID MaxVal.................. - Disabled
CIE Function........................ - Disabled
Execute Disable Bit................. - Disabled
Virtualization Technology........... - Disabled
Core Multi-Processing............... - Enabled

>DRAM Timing:

Enhance Data transmitting........... - Auto
Enhance Addressing.................. - Auto
T2 Dispatch......................... - Disabled

>Clock Setting Fine Delay Press Enter:

DLL And RCOMP Settings.............. - Auto
Ch1 Dram Defaul Skew................ - Model 0
Ch2 Dram Defaul Skew................ - Model 0
RCOMP Settings...................... - Model 2

Fine Delay Step Degree.............. - 70ps
Ch1 Clock Crossing Setting.......... - Auto
DIMM1 Clock Fine Delay.............. - Current[1346ps]
DIMM2 Clock Fine Delay.............. - Current[1346ps]
Ch1 Control0 Fine Delay............. - Current[166ps]
Ch1 Control1 Fine Delay............. - Current[166ps]
Ch1 Control2 Fine Delay............. - Current[124ps]
Ch1 Control3 Fine Delay............. - Current[110ps]
Ch1 Command Fine Delay.............. - Current[262ps]

Ch2 Clock Crossing Setting.......... - Auto
DIMM3 Clock Fine Delay.............. - Current[1346ps]
DIMM4 Clock Fine Delay.............. - Current[1346ps]
Ch2 Control0 Fine Delay............. - Current[14ps]
Ch2 Control1 Fine Delay............. - Current[56ps]
Ch2 Control2 Fine Delay............. - Current[0ps]
Ch2 Control3 Fine Delay............. - Current[0ps]
Ch2 Command Fine Delay.............. - Current[110ps]

Ch1 Ch2 Common Clock Setting........ - Auto

Ch1 RDCAS GNT-Chip Delay............ - Auto
Ch1 WRCAS GNT-Chip Delay............ - Auto
Ch1 Command To CS Delay............. - Auto
.
Ch2 RDCAS GNT-Chip Delay............ - Auto
Ch2 WRCAS GNT-Chip Delay............ - Auto
Ch2 Command To CS Delay............. - Auto

Flex Memory Mode..................... - Auto
CAS Latency Time (tCL)............... - 5
RAS# to CAS# Delay (tRCD)............ - 5
RAS# Precharge (tRP)................. - 5
Precharge Delay (tRAS)............... - 15
All Precharge to Act................. - Auto
REF to ACT Delay (tRFC).............. - Auto
Performance Level.................... - Auto

>Read delay phase adjust Press Enter:

Channel 1 Phase 0 Pull-In........... - Auto
Channel 1 Phase 1 Pull-In........... - Auto
Channel 1 Phase 2 Pull-In........... - Auto
Channel 1 Phase 3 Pull-In........... - Auto
Channel 1 Phase 4 Pull-In........... - Auto

Channel 2 Phase 0 Pull-In........... - Auto
Channel 2 Phase 1 Pull-In........... - Auto
Channel 2 Phase 2 Pull-In........... - Auto
Channel 2 Phase 3 Pull-In........... - Auto
Channel 2 Phase 4 Pull-In........... - Auto

Write to PRE Delay (tWR)............ - Auto
Rank Write to Read (tWTR)........... - Auto
ACT to ACT Delay (tRRD)............. - Auto
Read to Write Delay (tRDWR)......... - Auto
Ranks Write to Write (tWRWR)........ - Auto
Ranks Read to Read (tRDRD).......... - Auto
Ranks Write to Read (tWRRD)......... - Auto
ALL PRE to Refresh.................. - Auto

>Voltage Settings:

CPU VID Control..................... - 1.36250V
CPU VID Special Add................. - Enabled
CPU VID Special Add................. - Auto
DRAM Voltage Control................ - 2.21v
SB Core/CPU PLL Voltage............. - 1.55v
NB Core Voltage..................... - 1.408v
CPU VTT Voltage..................... - 1.303v
Vcore Droop Control................. - Disabled
Clockgen Voltage Control............ - 3.45v
GTL+ Buffer Strength................ - Strong
CPU GTL 0 REF Volt.................. - 0.6250
CPU GTL 2 REF Volt.................. - 0.6250
CPU GTL 1 REF Volt.................. - 0.6250
CPU GTL 3 REF Volt.................. - 0.6250
North Bridge GTL 0 REF Volt......... - 0.6250
North Bridge GTL 1 REF Volt......... - 0.6250
FSB Vref............................ - Auto

Genie BIOS Settings:

Exist Setup Shutdown................ - Mode 2
Exist Shutdown After AC loss........ - Enabled
AC Shutdown Free.................... - Enabled
O.C Clock Fail Retry Counter........ - 1
O.C Clock Fail CMOS Reloaded........ - Disabled
CPU Clock Ratio..................... - 9.5
Target CPU Clock.................... - 4275MHz
CPU Clock........................... - 450
Boot Up Clock....................... - Auto
CPU Clock Amplitude................. - 800mV
CPU Clock0 Skew..................... - 0ps
CPU Clock1 Skew..................... - 0ps
DRAM Speed.......................... - 400/800
Target DRAM Speed................... - 900MHz
PCIE Clock.......................... - 100mhz
PCIE Slot Config.................... - 1x 1x
CPU Spread Spectrum................. - Disabled
PCIE Spread Spectrum................ - Disabled__________________


These are my bios settings. I dotn have much trouble getting the cpu up and running as fast as i want, but i cant get the memory as fast as i want. I know i can run it 1200MHz at 2.2V as i could on my old board, but the DFI keeps crapping out even at 1100MHz.

I must atmid that i dont know much about overclocking memory, so i probably have overlooked a setting that is holding me back, but i got nu idee what setting

Aybody that can push me in the right derection?

[kamieldehond]

Ok this is funny. I had lots of problems getting my memory stable at high frequenties (using memtest86+). So i was upping NB voltage, but this wasnt helping. So I upped the NB to 1.5V and notived i got more errors in memtest. So decreasing NB voltage to 1.35 volts did the trick for me to get more stability.

fsb: 575
divider: 333/667
CAS: 6 - 5 - 5 - 15

[kamieldehond]

fsb 575 1h orthos stable

more to come

[GrandMasterJ]

fsb 575 1h orthos stable

more to come

Well done kamie. Those are very nice voltages for 575FSB.

I'm stuck at 520FSB....I fail Prime95 640k thread (I run a full test, find where a specific failure is, and see if I can pass just that thread multiple times) after 45 minutes no matter what voltages I use. 520FSB seems to be stable at 1.19v VTT and 1.29v FSB for me.

Can I see your 575FSB full settings? Thanks.

[kamieldehond]

Well done kamie. Those are very nice voltages for 575FSB.

I'm stuck at 520FSB....I fail Prime95 640k thread (I run a full test, find where a specific failure is, and see if I can pass just that thread multiple times) after 45 minutes no matter what voltages I use. 520FSB seems to be stable at 1.19v VTT and 1.29v FSB for me.

Can I see your 575FSB full settings? Thanks.

sorry. been a long time for me that i looked here. Anyway, I cant ge anything higher then 500 FSB stable on this board.

Ppl stiull using this board?

[kamieldehond]

Well done kamie. Those are very nice voltages for 575FSB.

I'm stuck at 520FSB....I fail Prime95 640k thread (I run a full test, find where a specific failure is, and see if I can pass just that thread multiple times) after 45 minutes no matter what voltages I use. 520FSB seems to be stable at 1.19v VTT and 1.29v FSB for me.

Can I see your 575FSB full settings? Thanks.

oh and i also dont have the settings for 575 fsb anymore

[kitfit1]

sorry. been a long time for me that i looked here. Anyway, I cant ge anything higher then 500 FSB stable on this board.

Ppl stiull using this board?

Have a look at these settings. Although they are for 563fsb, they should give you a good idea as to what you may need to change.