Micron D9 GMH\GKX\JKH etc club

[tool_462]

Nice! Yet another satisfied convert from MIIF to UD3P Was the best motherboard change I ever made.

[RPGWiZaRD]

Just wanted to report my 2nd 2x1GB CellShock DDR2-1000 4-4-4-12 D9GKX kit died on me after only ~3 months of usage at 2.15v. I almost never turn off the computer, it usually runs 24/7, only when I go away for like a day and fear there might be some thunderstorm which was the case now and I turned comp off and flicked psu power switch off and pulled out the power cables from wall socket. Then when I want to turn on the comp again it simply didn't wanna post, but what's more weird is that both sticks were dead, putting some backup ram kit in and it posted immediatly. I think it might be some incompability with this Gigabyte P35 DS4 board and micron D9GKX ram, I had some Team Xtreem D9GMH which I used for like 1½ year (bought it of another person and it was old from 2005) tho until one stick became a bit bad, had trouble booting. But sometimes I also hear some weird electric noise when flicking off the PSU power switch, but it's very rare but perhaps there's some probs with it.

So now it's the 2nd time I RMA this kit. :p I was questioning whetever or not to do it as I'm planning to upgrade to Socket 1156 in near future anyway but for 3.50 EUR I might as well do it for such awesome clocking DDR2 ram.

[Shiranui Gen-An]

After struggling to clock my new Team 8500 D9GMH kit past 600MHz (seriously) with the UD3P, I got frustrated and decided to pull my UT P35 back out. Lesson learned: Never send a Gigabyte to do a DFI's job.

[zsamz_]

After struggling to clock my new Team 8500 D9GMH kit past 600MHz (seriously) with the UD3P, I got frustrated and decided to pull my UT P35 back out. Lesson learned: Never send a Gigabyte to do a DFI's job.

the ut just loves da gmh
not all UD3P are created equal nothin new
but 99% of utp35 rock

[CryptiK]

This is what my DFI DK X48-T2RSB Plus managed with a kit of Team Group D9 GMH on DICE.

751.7 MHz / 5-5-5-15 / 3.08 vdimm



To see the pics and other results check out my thread:

DFI DK X48-T2RSB-Plus + D9 GMH + DICE

[Ket]

Your hate toward Gigabyte is unjustified There are lots of people who get really good clocks from the UD3P, and come to think of it, many get good numbers from the P5Q series as well

[Shiranui Gen-An]

More fun with the UT P35 and these Team 8500 sticks. I still can't get the low voltage 32M stability others have, I'm not sure if it's my components or the temps in my computer room.

[Shiranui Gen-An]

740 C5 reached with UD3 ...don't gat the screenies atmo but workin' on this rig for now and don't miss tha MIIF fa sure ^^
Don't even tried C4 :/ but I'll do it !! so pleasant to get high memory frequencies in DDR2 \o/

3D's goin' on @700 C5 5/5/5/15/42 2T with 2,6v, but encreasing voltage don't give me any stability over there ...for 32M I have to get more time lol

Can you share some of your settings for 740 C5? Are you using the Memory OC profiles?

[pvhk]

hi everybody!
my gskill 8500HK (d9gmh) work great on the DFI BI P45 elite w/q9550!
strap333/800 PL auto:

[ezaleina]

My 4x1GB Team Xtreem 8500 ( D9GMH ).,need at least 2.18v to pass 1Mb PI test.,is the volt save for 24/7 guys.?cool it with Corsair Airflow..

[IMG][/IMG]

[RPGWiZaRD]

Well I've seen D9 sticks fail at 2.05v and some sticks that have worked fine for over a year at 2.3v... So it's difficult to say but after experiencing some early death for my D9GKX sticks twice on this Gigabyte P35 board I think it depends a lot on the motherboard too.

Currently running my backup CellShock DDR2-1000 CL5 D9GMH sticks at 2.29v until the others arrive from RMA to be able to run them at same settings my CellShock DDR2-1000 CL4 D9GKX was at 2.10~2.15v. I'm that person that can't satisfy myself with lower speeds than what I used to have and rather push the hardware a bit more instead. Have 2x80mm fans as cooling tho.

[zsamz_]

Well I've seen D9 sticks fail at 2.05v and some sticks that have worked fine for over a year at 2.3v... So it's difficult to say but after experiencing some early death for my D9GKX sticks twice on this Gigabyte P35 board I think it depends a lot on the motherboard too.

Currently running my backup CellShock DDR2-1000 CL5 D9GMH sticks at 2.29v until the others arrive from RMA to be able to run them at same settings my CellShock DDR2-1000 CL4 D9GKX was at 2.10~2.15v. I'm that person that can't satisfy myself with lower speeds than what I used to have and rather push the hardware a bit more instead. Have 2x80mm fans as cooling tho.

nothin new to me to lose good d9 on gigabut boards
i was averaging 1 set evert 4-5 weeks on gigabyte p35

[lha]

Have posted this while ago on this thread maybe.

Some more MIIF tribute: http://valid.canardpc.com/show_oc.php?id=530225
1x Transcend aXeram 1200mhz+ @ 700mhz 5-4-4-4 @ 3.2 V

[Don_Dan]

More fun with the UT P35 and these Team 8500 sticks. I still can't get the low voltage 32M stability others have, I'm not sure if it's my components or the temps in my computer room.

Who cares about low voltage stability anyway?!

Nice going on the DFI, though I still can't believe you couldn't get past 600MHz on the UD3P...

Which PL were you running in your last result?

[Shiranui Gen-An]

Who cares about low voltage stability anyway?!

Nice going on the DFI, though I still can't believe you couldn't get past 600MHz on the UD3P...

Which PL were you running in your last result?

I think it was PL7 with 444FSB on the 266/800 divider.

[Don_Dan]

I think it was PL7 with 444FSB on the 266/800 divider.

Thanks for the reply!

Did you test how high you can run the FSB with PL7? P35 chipsets are usually able to run PL a tad lower than P45 at the same FSB frequency, that's why this could be quite interesting for generating bandwidth.

[BeepBeep2]

nothin new to me to lose good d9 on gigabut boards
i was averaging 1 set evert 4-5 weeks on gigabyte p35

If you set drive strengths down they don't die...

[kuebk]

At last got my ballistix tracers 1066 workings as I wanted to, 2.14v:

[zsamz_]

If you set drive strengths down they don't die...

you dont know what you talkin about
no options for drive strength in p35
pos memory voltage regulators on gigabut p35

[Blue Storm]

Cell Shock 1000MHz CL4 @ 1120MHz 4-4-4-4 with 2.3V on Gigabyte EP45-Extreme, but I don't know if stable

http://valid.canardpc.com/show_oc.php?id=660951

[kuebk]

Same tracers as few post earlier, same voltage [2.14] - imo gg mem.

[Gaul]

THE BEST MICRON I EVER SEE AND HAVE

FSB 1280 CL 5/5/5/15 v 2.14

[Mafio]

Cell Shock 1000MHz CL4 @ 1120MHz 4-4-4-4 with 2.3V on Gigabyte EP45-Extreme, but I don't know if stable

http://valid.canardpc.com/show_oc.php?id=660951

good ram and awesome mobo

ep45 extreme is the best mobo for ram clocking, with cellshock on it you must do at least 1200mhz cas4

[kuebk]

Gaul what sticks?

[Gaul]

Gaul what sticks?

team extreem pc 8500, 2x1 GB kit