16.235s SuperPi 1m Phenom II 955

[chew*]

Next backup.

The efficiency comes from not cracking 3k yet once you crack 3K NB effecieny dies until about 4500 mhz cpu.

Bench went higher not taking screenies at OC knob speed.

4 clicks up by middle of run.

[crazydiamond]

how does that knob work is it just bumping the bus? were those 2 runs identical besides the fact that the 2nd you went to the '4th click' rather than the 3rd?

[chew*]

yah preety much.....trying to figure out how much i'm losing to delay time...I think if I hit it by 9th iteration it will apply at 10th.

So every click = Higher ram, higher cpu and higher NB higher HT.

[Zeus]

So 4 notches up means CPU-Z screen speed+4x20.5MHz= 4264.4+82= 4346.4MHz, right?

[chew*]

Something like that but not for entire bench.

Wow you smoked by one of my backups.

5 clicks up a little sooner than halfway point.......

[Zeus]

Dang, i'm out of back ups.

Well done chew*

I will shoot for more but i have a busy schedule for the couple of next days.

Why do you turn the speed up halfway the run instead of at the start?

[chew*]

Dang, i'm out of back ups.

Well done chew*

I will shoot for more but i have a busy schedule for the couple of next days.

Why do you turn the speed up halfway the run instead of at the start?

Heat.

Fail at a little more than halfway through bench, so if I turn up at halfway I avoid the initial heat.

I got one run to pass finally while toggling between 5 and 6 clicks...

Think my rams at limit due to non convergent i got multiple times attempting it.

[Zeus]

So you start out at ~4260MHz and then somewhere halfway the run you just up the frequency about 100MHz?

How come the entire run is still fast and not just the second part?

And why does CPU-Z not update?

With tweak it CPU-Z reads out correct, or do you turn the speed down again right after the run finished?

[Slappa]

Well done guys. I'd love to play with tweak it or an OC knob.

I expect to see you rebuttal to chew*'s backup Zeus, you can do it.

[chew*]

So you start out at ~4260MHz and then somewhere halfway the run you just up the frequency about 100MHz?

How come the entire run is still fast and not just the second part?

And why does CPU-Z not update?

With tweak it CPU-Z reads out correct, or do you turn the speed down again right after the run finished?

Because I Tweaked my OS and hardware for PI 1m only now 74MB system ram usage and alot of junk removed from OS, subtimings tight now etc etc. Planning on flattening it so I didn't care. Still a few more things I could do. Fresh install, SP1, wazza, max mem etc etc.

Turning it down to avoid a possible crash screen shotting at rather high speeds with all cores.

[Norz]

Something like that but not for entire bench.

Wow you smoked by one of my backups.

5 clicks up a little sooner than halfway point.......

...damn, are you kidding me
i love that run ...what cooling used?

I wanna buy you a beer just for that screen...lol

[chew*]

...damn, are you kidding me
i love that run ...what cooling used?

I wanna buy you a beer just for that screen...lol

Wait untill he makes me use the backup of this gonna wish he did not make me swap cpu's.

[Zeus]

Because I Tweaked my OS and hardware for PI 1m only now 74MB system ram usage and alot of junk removed from OS, subtimings tight now etc etc. Planning on flattening it so I didn't care. Still a few more things I could do. Fresh install, SP1, wazza, max mem etc etc.

Turning it down to avoid a possible crash screen shotting at rather high speeds with all cores.

You cheater! I want to see a screen with the real speed!

Still, i think my efficiency is better, non of your runs had a <68K Performance Product but i'm not sure since the real speed is not in the screen.

Wait untill he makes me use the backup of this gonna wish he did not make me swap cpu's.

It might take some time i will make you break out that damn back up score, hahaha.

I'm gonna need need some cold ambient though, that last screen was pretty much the max at that moment, ambient then was ~15ºC.
The forecast show some cold nights (~10ºC) so i hope i can find some time to fight back.

[chew*]

You cheater! I want to see a screen with the real speed!

Still, i think my efficiency is better, non of your runs had a <68K Performance Product but i'm not sure since the real speed is not in the screen.

Yah I opted to use ram similar to yours...I could break 68K easy with other sets......this set does not like 6-6-6 but my other sets would give me a huge advantage, wanted to keep playing field somewhat even.

[Slappa]

DICE cooling
5016MHz 1 core, all other cores @ 4807MHz
NB 2926MHz
Ram 1672MHz 7-7-5-15-22-1T

[m411b]

Wheres the rest of the screenshot? Nice times!

[Zeus]

Nice one Slappa!

[Slappa]

Wheres the rest of the screenshot? Nice times!

To ensure I didn't crash, I didn't have anything else open during the run

Nice one Slappa!

Thanks

[m411b]

Ok, Ive been working on this all day! 25*c ambient. Still not as good as chew* or Slappa, but its getting there! I gotta get some better ram.



My Best was this:


Did manage to get a validation @ 4.3Ghz though


http://valid.canardpc.com/show_oc.php?id=603094

[m411b]

My best with this ram!

[Slappa]

My best with this ram!

Nice run

[chew*]

Been putting the screws to a new set of 2x2g ram........No 1m becasue that won't tell me much stability wise....

A little tweaking at the same speed goes a looooooooonnngg way.

[Zeus]

Wow man, what did you do between the 2nd and 3rd screen? Quite a big step you took there!

Nice going and lovely cpu, assuming it's still on water.

[chew*]

Wow man, what did you do between the 2nd and 3rd screen? Quite a big step you took there!

Nice going and lovely cpu, assuming it's still on water.

Advanced ram tweaking

Air this is one of the ones you don't want me to put on water

[FlanK3r]

my new one the best for me
AIR cooling, 4120MHz / 2884MHz NB 1M=16.705s