Asus P6T Deluxe Discussion Thread

[Buggalugs]

How do you get it to display actual voltages?

My TurboV only show the settings.

Oh ya sorry its not actual voltages. I dont think there is a sensor for vdimm on these boards.

[Formann]

hi all,
i'm a new in this field so forgive me my qustions.

With the default speed of the CPU i can put my ram to 2000Mhz.
but with this current speed the max of my ram speed is 1683.
the next speed is 2000 windows does not boot!
i don't know what i have to change to make it work


any help?
and also any advice to tweak these setting, i will be glade

i7 920 D0 Batch 3849A866
Asus P6T Deluxe V2 buis 406
RAM 6GB OCZ Blade DDR3 2000 cl9,

From 1683Mhz the next step is 2100Mhz.

Since UCLK needs to run at twice the speed of RAM, you need UCLK to run at 4200Mhz. Not all CPUs are able to do this, and certainly not on air.
You are already at 1.37v QPI/DRAM, and since its not recomended to run over 1.35 for 24/7 I wouldnt try to solve the problem by increasing the voltage.

It might also be that your RAM needs additional voltage, but since it wont even boot, my money is on the UCLK/Uncore. (1.65-1.7 is max recomended for 24/7)
Or, maybe the AUTO setting on DRAM Timing fails, and is running to tight. Try running Manual instead of AUTO and make sure the DRAM Timings are 9-9-9-30.

You should try running 21x multi (191x21). This way you can run 1900Mhz on RAM and you´ll only need 3800Mhz UCLK.

If you really want 2000Mhz, you need to increase BCLK to 200 and either run 20x multi or 4200Mhz on CPU (200x21).

Be aware that the 20x (all even multis?) usually requires higher CPU voltage than 19x and 21x (all odd?).

[Majed]

From 1683Mhz the next step is 2100Mhz.

Since UCLK needs to run at twice the speed of RAM, you need UCLK to run at 4200Mhz. Not all CPUs are able to do this, and certainly not on air.
You are already at 1.37v QPI/DRAM, and since its not recomended to run over 1.35 for 24/7 I wouldnt try to solve the problem by increasing the voltage.

It might also be that your RAM needs additional voltage, but since it wont even boot, my money is on the UCLK/Uncore. (1.65-1.7 is max recomended for 24/7)
Or, maybe the AUTO setting on DRAM Timing fails, and is running to tight. Try running Manual instead of AUTO and make sure the DRAM Timings are 9-9-9-30.

You should try running 21x multi (191x21). This way you can run 1900Mhz on RAM and you´ll only need 3800Mhz UCLK.

If you really want 2000Mhz, you need to increase BCLK to 200 and either run 20x multi or 4200Mhz on CPU (200x21).

Be aware that the 20x (all even multis?) usually requires higher CPU voltage than 19x and 21x (all odd?).

Good,
as soon as i went back to home will try your comments and post the results.

Thanks alot.

[DdotRoq]

Any place I can go to add a bunch of stuff to OC Palm and make it half as useful?

Also, I hope they come up with a fix soon. Running Quad-SLi, sometimes it can't decide which is the correct video card and makes the bottom one primary, so I have to shut off and turn on like 5 times until it realized that top one is primary.

[wez3570]

Hi all,

Does anyone know where I can get the Enzotech MST-73 and the MST-88 for the P6T deluxe?

Anywhere is the UK or anywhere that will ship to UK?

Just ordered a MIPS NB/SB waterblock but don't want to put the mosfets under water.

Anyone got any other solution idea?

Cheers guys

[mk_dir]

any help?
and also any advice to tweak these setting, i will be glade

Essentially use higher CPU Ratio (X21) and less BCLK in order to relax Uncore frequency.

[JPQY]

A little question..can i use a X5550 cpu on my Asus P6T Deluxe v2? or it's only working on a dual socket system?

Thanks,
JP.

[mk_dir]

A little question..can i use a X5550 cpu on my Asus P6T Deluxe v2?

AFAIK Xeon 55XX series only works in a 2P motherboard... however you can use a Xeon 35XX series in a 1P motherboard like the P6T V2.

[Burner27]

AFAIK Xeon 55XX series only works in a 2P motherboard... however you can use a Xeon 35XX series in a 1P motherboard like the P6T V2.

Will a Xeon 35XX work in a P6T V1 board?

Thx

[angelreaper]

Will a Xeon 35XX work in a P6T V1 board?

Thx

Yes, but very strange. No fully support

In the bios missing:

DRAM Multipliers other than 1:3 and 1:4
QPI Transfer Rate
Uncore Frequency

[Majed]

Okay.
here's my try.
this is the achievement i got and i think it's good so far,, but really i don't know about the heat.
i think 81c max is safe at 100% x8 load!??

here is the pic.

LinX test.

the droping in GFlops score cause i was using windows.
Prime95 Test





and this is my Bios Setting

CPU Ratio : 19
SpeedStep : Disable
BCLK : 206
PCIE : 101
DRAM: 1651
UCLK : Auto
QPI : Auto

DRAM Timing : 8:8:8:16

CPU Volt : 1.20625
CPU PPL : 1.80
QPI/DRAM : 1.26075
IOH Volt : 1.18
DRAM Bus  : 1.66

CPU Differential Amp : 800mV

* Skew : Disable.

CPU Tm Fun. : Disable
A20M: Disable
SpeedStep : Disable
left is auto

your thought.?

[bmg]

Yes, but very strange. No fully support

In the bios missing:

DRAM Multipliers other than 1:3 and 1:4
QPI Transfer Rate
Uncore Frequency

Does that also apply to the P6T Deluxe V2 with the latest bios?

[angelreaper]

Does that also apply to the P6T Deluxe V2 with the latest bios?

Yes. But more options is lock in bios, not only when working with Xeon:


For my xeon I buy EX58-EXTREME:

http://valid.canardpc.com/show_oc.php?id=577039

Now I`m happy

[Lu(ky]

I need some help with a friends build I am doing on a V2 board. For some reason I can not get the 2 x DVD-ROM drives to work, or show up under MYCOMPUTER? I am running 2 x 300GB WD VelociRaptor in a raid -0- with 1 x WD 640GB storage drive. All HD shows up fine but for some reason I can not get the DVD-ROM to show up? I am running BIOS 504. I am also running a 920 CO batch as of right now NO OCing just stock settings... If someone has any quick ideas would be great, I need to finish this build and give back to him. I think a SATA PORT may be dead. I ran a seperate line to my DVD-ROM and I smelt a electrical burning smell and shut system down. Has the V2 board ever had problems with the SATA PORTS like this?

[Lu(ky]

Found the problem 1 dead SATA PORT oh well I guess no plug in for the front panel sata on the case.. Just happy I found the problem now I can start the OCing fun...

[chuckbam]

CPU header is fine. But, I think chassis fans 2 & 3 are going. The will not work on boot. Ten, may start for a while and stop again. I keep Q-Fan Disabled. But, I turned them on an off and flashed the bios with no luck.

The PDF said max 84W. I think I using 8.64W. Worked fine for many months.

Think my board is damaged?

[angelreaper]

New bios for Asus P6T Deluxe - 1605
ftp://ftp.asus.com.tw/pub/asus/mb/lg...ELUXE-1605.zip

[bmg]

New bios for Asus P6T Deluxe - 1605
ftp://ftp.asus.com.tw/pub/asus/mb/lg...ELUXE-1605.zip

Fix the W3520 issues?

[TraX]

New bios for Asus P6T Deluxe - 1605
ftp://ftp.asus.com.tw/pub/asus/mb/lg...ELUXE-1605.zip

Thanks Also keen to hear if it fixed your W3520 issues?

[angelreaper]

Fix the W3520 issues?

Thanks Also keen to hear if it fixed your W3520 issues?

Someone else to say. I sold my P6T Deluxe V1/V2 and buy Gigabyte EX58-Extreme.

[ben805]

Someone else to say. I sold my P6T Deluxe V1/V2 and buy Gigabyte EX58-Extreme.

how do you like that Gigabyte in comparison to the Asus? worth the switch? and why not the UD5 instead of Extreme?

[angelreaper]

how do you like that Gigabyte in comparison to the Asus? worth the switch? and why not the UD5 instead of Extreme?

For my YES. Full support for Xeon:

Bios is very rich of options.
Extreme because no UD5 when they shop

[ben805]

nice, so if I wanted to run only air cooled on this Extreme version is the waterblock going to be a problem or does it come with a separte heatsink to swap out the block? and how hot does your VREG get when you were running LinX?

[JohnMike]

nice, so if I wanted to run only air cooled on this Extreme version is the waterblock going to be a problem or does it come with a separte heatsink to swap out the block? and how hot does your VREG get when you were running LinX?

Ben,

I had this Gigabyte Extreme in the past. This board like Asus is very cool, it stay warm @load, no need for air cooling or WC on the NB, maybe only if you go SLI and don't have good airflow in side.

I know you don't like eVGA X58 SLI if there VREG high temps when @load, so you will be very pleased with the Extreme or UD5. From what i remenber the only 'weak point' of Gigabyte X58 boards was the slow boot when you power on the first time.

[Nocturno]

New bios for Asus P6T Deluxe - 1605
ftp://ftp.asus.com.tw/pub/asus/mb/lg...ELUXE-1605.zip

Can someone upload the file?
Link is broken...